Skip to main content
SpringerLink
Log in

Assessment of Interplay of Mud Cake and Failure Criteria on the Lower Limit of Safe Borehole Pressure

  • Original Paper
  • Published:
Indian Geotechnical Journal Aims and scope Submit manuscript

Abstract

Borehole instability is affected by heterogeneity of tectonic stresses, mud cake properties, and drilling fluid pressure. If the borehole pressure is greater than the safe upper limit pressure, it will lead to hydraulic fracture, and if it is less than the lower limit, it will lead to shear failure or borehole breakout. The purpose of this article is to calculate the lower limit of safe borehole pressure so that under this pressure, the borehole will not undergo shear failure. For this purpose, an analytical model is presented in which the effect of non-isotropic field stress, pore pressure changes and filter cake characteristics are considered. In the two-dimensional plane strain model, it is assumed that the mud cake has a perfect plastic behavior and is bonded to the borehole wall. By combining the elastic stress relations with shear failure criterion, close-form relations for the lower limit of safe borehole pressure and for 5 different failure criteria are obtained. According to the results, the presence of cake makes the stresses in the borehole wall more isotropic, and this strengthens the borehole against breakout. By increasing the thickness of the mud cake by 4 mm, the borehole pressure required to inhibit breakout is reduced by an average of 13.5%, and if the mud cake permeability increases 100 times, the minimum required pressure will increase by an average of 65%. If the ratio of in situ stresses increases from 2.6 to 3, the lower limit of safe borehole pressure increases by 33.8% on average.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4:
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13

Similar content being viewed by others

Explore related subjects

Discover the latest articles, news and stories from top researchers in related subjects.

Data Availability

The data used to support the findings of this study are included within the article.

References

  1. Abou-Sayed AS, Brechtel CE, Clifton RJ (1978) In situ stress determination by hydrofracturing: a fracture mechanics approach. J Geophys Res Solid Earth 83(B6):2851–2862. https://doi.org/10.1029/JB083iB06p02851

    Article  Google Scholar 

  2. Bunger AP, Lakirouhani A, Detournay E (2010) Modelling the effect of injection system compressibility and viscous fluid flow on hydraulic fracture breakdown pressure. Paper presented at the ISRM international symposium on in-situ rock stress

  3. Lakirouhani A, Jolfaei S (2023) Hydraulic fracturing breakdown pressure and prediction of maximum horizontal in situ stress. Adv Civ Eng 2023:8180702. https://doi.org/10.1155/2023/8180702

    Article  Google Scholar 

  4. Jolfaei S, Lakirouhani A (2022) Sensitivity analysis of effective parameters in borehole failure, using neural network. Adv Civ Eng 2022:4958004. https://doi.org/10.1155/2022/4958004

    Article  Google Scholar 

  5. Bradley WB (1979) Failure of inclined boreholes. J Energy Res Technol 101(4):232–239. https://doi.org/10.1115/1.3446925

    Article  Google Scholar 

  6. McLean MR, Addis MA (1990) Wellbore stability: the effect of strength criteria on mud weight recommendations. Paper presented at the SPE annual technical conference and exhibition. https://doi.org/10.2118/20405-MS

  7. McLellan P, Hawkes C (2001) Borehole stability analysis for underbalanced drilling. J Can Pet Technol. https://doi.org/10.2118/01-05-01

    Article  Google Scholar 

  8. Morita N (2004) Well orientation effect on borehole stability. Paper presented at the SPE annual technical conference and exhibition. https://doi.org/10.2118/89896-MS

  9. Wang X, Sterling RL (2007) Stability analysis of a borehole wall during horizontal directional drilling. Tunn Undergr Space Technol 22(5):620–632. https://doi.org/10.1016/j.tust.2007.01.002

    Article  Google Scholar 

  10. Zhang J (2013) Borehole stability analysis accounting for anisotropies in drilling to weak bedding planes. Int J Rock Mech Min Sci 60:160–170. https://doi.org/10.1016/j.ijrmms.2012.12.025

    Article  Google Scholar 

  11. Chuanliang Y, Jingen D, Xiangdong L, Xiaorong L, Yongcun F (2014) Borehole stability analysis in deepwater shallow sediments. J Energy Resour Technol. https://doi.org/10.1115/1.4027564

    Article  Google Scholar 

  12. Maleki S, Gholami R, Rasouli V, Moradzadeh A, Riabi RG, Sadaghzadeh F (2014) Comparison of different failure criteria in prediction of safe mud weigh window in drilling practice. Earth Sci Rev 136:36–58. https://doi.org/10.1016/j.earscirev.2014.05.010

    Article  Google Scholar 

  13. Ma T, Chen P, Yang C, Zhao J (2015) Wellbore stability analysis and well path optimization based on the breakout width model and Mogi–Coulomb criterion. J Pet Sci Eng 135:678–701. https://doi.org/10.1016/j.petrol.2015.10.029

    Article  Google Scholar 

  14. Ma T, Yang Z, Chen P (2018) Wellbore stability analysis of fractured formations based on Hoek–Brown failure criterion. Int J Oil Gas Coal Technol 17(2):143–171. https://doi.org/10.1504/IJOGCT.2018.089934

    Article  Google Scholar 

  15. Su H, Ma H, Hu B, Qu C, Wang N (2018) An analysis of drilling fluid pumping pressure for the Maxi-HDD crossing project. Arab J Geosci 11(13):347. https://doi.org/10.1007/s12517-018-3708-y

    Article  Google Scholar 

  16. Zhang H, Pan D, Zhai L, Zhang Y, Chen C (2018) Stability analysis in determining safety drilling fluid pressure windows in ice drilling boreholes. Energies. https://doi.org/10.3390/en11123378

    Article  Google Scholar 

  17. Darvishpour A, Cheraghi Seifabad M, Wood DA, Ghorbani H (2019) Wellbore stability analysis to determine the safe mud weight window for sandstone layers. Pet Explor Dev 46(5):1031–1038. https://doi.org/10.1016/S1876-3804(19)60260-0

    Article  Google Scholar 

  18. Liu H, Cui S, Meng Y, Fan Y, Liu T, Yu A, Hu Z (2020) Wellbore stability evaluation method based on the continuous tangent envelope of a Mohr circle. Sci Prog 103(1):36850419888465. https://doi.org/10.1177/0036850419888465

    Article  Google Scholar 

  19. Abdulaziz AM, Abdulridha HL, Dahab ASA, Alhussainy S, Abbas AK (2021) 3D mechanical earth model for optimized wellbore stability, a case study from South of Iraq. J Pet Explor Prod Technol 11(9):3409–3420. https://doi.org/10.1007/s13202-021-01255-6

    Article  Google Scholar 

  20. Zhang F, Liu H-B, Cui S, Meng Y-F, Wang J-J (2021) Influence of the weakening effect of drilling fluid on wellbore stability in anisotropic shale formation. Front Phys 9:745075. https://doi.org/10.3389/fphy.2021.745075

    Article  Google Scholar 

  21. Ma T, Peng N, Chen P (2020) Filter cake formation process by involving the influence of solid particle size distribution in drilling fluids. J Natl Gas Sci Eng 79:103350. https://doi.org/10.1016/j.jngse.2020.103350

    Article  Google Scholar 

  22. Guo Q, Cook J, Way P, Ji L, Friedheim JE (2014) A comprehensive experimental study on wellbore strengthening. Paper presented at the IADC/SPE drilling conference and exhibition. https://doi.org/10.2118/167957-MS

  23. Feng Y, Li X, Gray KE (2018) An easy-to-implement numerical method for quantifying time-dependent mudcake effects on near-wellbore stresses. J Pet Sci Eng 164:501–514. https://doi.org/10.1016/j.petrol.2018.01.051

    Article  Google Scholar 

  24. Hashemzadeh SM, Hajidavalloo E (2016) Numerical investigation of filter cake formation during concentric/eccentric drilling. J Pet Sci Eng 145:161–167. https://doi.org/10.1016/j.petrol.2016.03.024

    Article  Google Scholar 

  25. Bailey L, Meeten G, Way P, L'Alloret F (1998) Filtercake Integrity and Reservoir Damage. Paper presented at the SPE formation damage control conference. https://doi.org/10.2118/39429-MS

  26. Griffith J, Osisanya SO (1999) Effect of drilling fluid filter cake thickness and permeability on cement slurry fluid loss. J Can Pet Technol. https://doi.org/10.2118/99-13-15

    Article  Google Scholar 

  27. Cerasi P, Ladva HK, Bradbury AJ, Soga K (2001) Measurement of the mechanical properties of filtercakes. Paper presented at the SPE European formation damage conference. https://doi.org/10.2118/68948-MS

  28. Cook J, Guo Q, Way P, Bailey L, Friedheim J (2016) The role of filtercake in wellbore strengthening. Paper presented at the IADC/SPE drilling conference and exhibition. https://doi.org/10.2118/178799-MS

  29. Jaffal HA, El Mohtar CS, Gray KE (2017) Modeling of filtration and mudcake buildup: an experimental investigation. J Natl Gas Sci Eng 38:1–11. https://doi.org/10.1016/j.jngse.2016.12.013

    Article  Google Scholar 

  30. Haimson BC, Lee MY (1995) Estimating in situ stress conditions from borehole breakouts and core disking-experimental results in granite. In: Proceedings of the international workshop on rock stress measurement at great depth, 8th ISRM Congress, Tokyo, Japan, pp 19–24

  31. Shen B, Stephansson O, Rinne M (2002) Simulation of borehole breakouts using FRACOD2D. Oil Gas Sci Technol 57(5):579–590. https://doi.org/10.2516/ogst:2002039

    Article  Google Scholar 

  32. Cuss RJ, Rutter EH, Holloway RF (2003) Experimental observations of the mechanics of borehole failure in porous sandstone. Int J Rock Mech Min Sci 40(5):747–761. https://doi.org/10.1016/S1365-1609(03)00068-6

    Article  Google Scholar 

  33. Lakirouhani A, Bahrehdar M, Medzvieckas J, Kliukas R (2021) Comparison of predicted failure area around the boreholes in the strike-slip faulting stress regime with Hoek–Brown and Fairhurst generalized criteria. J Civ Eng Manag. https://doi.org/10.3846/jcem.2021.15020

    Article  Google Scholar 

  34. Bahrehdar M, Lakirouhani A (2022) Evaluation of the depth and width of progressive failure of breakout based on different failure criteria, using a finite element numerical model. Arab J Sci Eng. https://doi.org/10.1007/s13369-022-06640-9

    Article  Google Scholar 

  35. Feng Y, Li X, Gray KE (2018) Mudcake effects on wellbore stress and fracture initiation pressure and implications for wellbore strengthening. Pet Sci 15(2):319–334. https://doi.org/10.1007/s12182-018-0218-1

    Article  Google Scholar 

  36. Aadnøy BS, Belayneh M (2004) Elasto–plastic fracturing model for wellbore stability using non-penetrating fluids. J Pet Sci Eng 45(3):179–192. https://doi.org/10.1016/j.petrol.2004.07.006

    Article  Google Scholar 

  37. Fjaer E, Holt RM, Horsrud P, Raaen AM, Risnes R (2008) Petroleum related rock mechanics. Elsevier, London (ISBN 978-0-444-50260-5)

    Google Scholar 

  38. Lakirouhani A, Hasanzadehshooiili H (2011) Review of rock strength criteria. In: Proceedings of the 22nd world mining congress & Expo. Istanbul, Turkey, 2011, pp 473–482

  39. Fairhurst C (1964) On the validity of the ‘Brazilian’ test for brittle materials. Int J Rock Mech Min Sci Geomech Abstracts 1(4):535–546. https://doi.org/10.1016/0148-9062(64)90060-9

    Article  Google Scholar 

  40. Jaeger JC, Cook NG, Zimmerman R (2009) Fundamentals of rock mechanics. Wiley

    Google Scholar 

  41. Hoek E, Brown ET (1980) Empirical strength criterion for rock masses. J Geotech Geoenviron Eng 106:1013–1035. https://doi.org/10.1061/AJGEB6.0001029

    Article  Google Scholar 

  42. Al-Ajmi AM, Zimmerman RW (2006) Stability analysis of vertical boreholes using the Mogi–Coulomb failure criterion. Int J Rock Mech Min Sci 43(8):1200–1211. https://doi.org/10.1016/j.ijrmms.2006.04.001

    Article  Google Scholar 

  43. Zhou S (1994) A program to model the initial shape and extent of borehole breakout. Comput Geosci 20(7):1143–1160. https://doi.org/10.1016/0098-3004(94)90068-X

    Article  Google Scholar 

  44. Liu X, Civan F (1994) Formation damage and skin factor due to filter cake formation and fines migration in the Near-Wellbore Region. Paper presented at the SPE formation damage control symposium. https://doi.org/10.2118/27364-MS

  45. Bezemer C, Havenaar I (1966) Filtration behavior of circulating drilling fluids. Soc Pet Eng J 6(04):292–298. https://doi.org/10.2118/1263-PA

    Article  Google Scholar 

  46. Badrul MJ, Chiou LL, Azlina Z, Juliana Z (2007) Dolomite as an alternative weighting agent in drilling fluids. J Eng Sci Technol 2(2):164–176

    Google Scholar 

  47. Chenevert ME, Dewan JT (2001) A model for filtration of water-base mud during drilling: determination of mudcake parameters. Petrophys. SPWLA J Form Eval Reserv Descr 42(03):237

    Google Scholar 

  48. Wu J, Torres-Verdín C, Sepehrnoori K, Proett MA (2005) The influence of water-base mud properties and petrophysical parameters on mudcake growth, filtrate invasion, and formation pressure. Petrophys SPWLA J Format Eval Reserv Descr 46(01). https://onepetro.org/petrophysics/article-abstract/171075/The-Influence-of-Water-Base-Mud-Properties-and?redirectedFrom=PDF

  49. Lee H, Moon T, Haimson BC (2016) Borehole breakouts induced in Arkosic sandstones and a discrete element analysis. Rock Mech Rock Eng 49(4):1369–1388. https://doi.org/10.1007/s00603-015-0812-0

    Article  Google Scholar 

Download references

Acknowledgements

The authors would like to acknowledge the University of Zanjan for providing the necessary resources and facilities for this research.

Funding

This research received no specific grant from any funding agency in the public, commercial, or not-for-profit sectors.

Author information

Authors and Affiliations

  1. Department of Civil Engineering, Faculty of Engineering, University of Zanjan, Zanjan, Iran

    Mohammad Bahrehdar & Ali Lakirouhani

Authors
  1. Mohammad Bahrehdar
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ali Lakirouhani
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

All authors contributed to the study conception and design. All authors read and approved the final manuscript.

Corresponding author

Correspondence to Ali Lakirouhani.

Ethics declarations

Conflict of interest

The authors declare that they have no conflicts of interest.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Bahrehdar, M., Lakirouhani, A. Assessment of Interplay of Mud Cake and Failure Criteria on the Lower Limit of Safe Borehole Pressure. Indian Geotech J (2024). https://doi.org/10.1007/s40098-023-00856-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40098-023-00856-8

Keywords

Search

Navigation