Flow mapping using 3D full-scale CFD simulation and hydrodynamic experiments of an ultra-supercritical turbine’s combined valve for nuclear power plant

Abstract

In a typical steam turbine generator system, electrical power output is related to the steam flow regulated by a control valve. Hence, to ensure adequate electrical load as well as the proper stability of the turbine, a linear operation of the control valve is desired. However, in reality, the control valve exhibits different flow characteristics (FCs), both linear and nonlinear, which stem from its complex shape of plug and stem lift. Therefore, precise estimation of FCs is of utmost importance for better controllability, reliability, and safety of the turbine system. In this study, experiments and CFD simulations were carried out to evaluate the hydrodynamic FCs of a combined emergency stop and control valve to be employed in an ultra-supercritical (USC) turbine system for power plant. A full-scale prototype valve was designed, fabricated, and tested for a vendor company. Experiments were performed in the so-called VELO (Valve Engineering Layout Operation) test bench, and CFD simulations were conducted using a commercial code STAR CCM+. Air was used for experiments and simulations for simple economic and safe operation. Hydrodynamic characteristics were analyzed, and the theoretical mass flow rate of the valve was estimated. Finally, the valve coefficient of the turbine system was determined from the obtained FC curves. The simulation and test data showed a scale deviation of 15–16% for the original model valve and the simplified test valve. The test valve required such scaled modification to match with the test bench and fabrication. The prospective future research and improvement were recommended. This study's findings would support improving the turbine system performance to ensure safer, reliable, and modular power conversion systems for nuclear and conventional fossil fuel-based power plants.

This is a preview of subscription content, access via your institution.

Fig. 1

Taken from PHILOSOPHIA, Inc

Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26

Abbreviations

A :

Cross-sectional area [m2]

a :

Acoustic velocity [m/s]

C q :

Flow coefficient

D :

Seat diameter [m]

FC:

Flow characteristics

h :

Specific enthalpy [J/kg]

L :

Length of pipe and valve stem lift [m]

Ma:

Mach number

\(\dot{m}\) :

Mass flow rate [kg/s]

p :

Pressure in gas [Pa]

R :

Gas constant [kJ/kgK]

T :

Temperature [K]

V :

Velocity [m/s]

ν :

Specific volume [m3/kg

κ :

Specific heat ratio

ρ :

Density [kg/m3]

ψ :

Pressure ratio as a function of mass flow

a:

Actual

e:

Outlet

i:

Inlet

o:

Total

s:

Seat

t:

Theoretical

N:

Nozzle

s:

Steam

CV:

Control valve

SV:

Stop valve

References

  1. 1.

    IEA, International Energy Agency: World Energy Outlook 2012 Executive Summary. OECD/IEA-Paris France (2012)

  2. 2.

    Brouwer, A.S., van den Broek, M., Seebregts, A., Faaij, A.: Operational flexibility and economics of power plants in future low-carbon power systems. Appl. Energy 156, 107–128 (2015)

    Article  Google Scholar 

  3. 3.

    Hutchison, J.M.: ISA Handbook of Control Valves. Instrument Society of America, Research Triangle Park, North Carolina, USA (1976)

    Google Scholar 

  4. 4.

    Johnson, L.H., Couchman, R.S., Spencer, R.C., Booth, J.A., Holman, R.J.: Method for Operating a Steam Turbine with an Overload Valve. General Electric Company, New York, USA (1983)

    Google Scholar 

  5. 5.

    Mirandola, A., Stoppato, A., Benato, A.: Steam power generation. In: Handbook of Clean Energy Systems, pp. 1–18 (2015)

  6. 6.

    Saito, E., Nishimoto, S., Endo, H., Yamamoto, R., Kawasaki, K., Sato, J.: Development of 700 °C class steam turbine technology. Mitsubishi Heavy Industries Technical Review 54(3), 10–15 (2017)

    Google Scholar 

  7. 7.

    Cziesla, F., Bewerunge, J., Senzel, A.: Luenen—state-of-the-art ultra supercritical steam power plant under construction. PowerGen Europe 2009, 26–29 May 2009 Cologne, Germany

  8. 8.

    Bhowmik, P.K.: Nanofluid Operation and Valve Engineering of SUPER for Small Unit Passive Enclosed Reactor. Department of Nuclear Engineering, Seoul National University, Seoul, Republic of Korea (2016)

    Google Scholar 

  9. 9.

    Quinkertz, R., Ulma, A., Gobrecht, E., Wechsung, M.: USC Steam Turbine technology for maximum efficiency and operational flexibility. Power-Gen Asia 2008, 17 (2008)

    Google Scholar 

  10. 10.

    Emerson Process Management Control Valve Handbook. 4th edn. Fisher; Control Valve Selection and Sizing. North America, Marshalltown, Iowa, USA (2005)

  11. 11.

    Halimi, B., Suh, K.Y.: Engineering nonlinearity characteristic compensation for commercial steam turbine control valve using linked MARS code and Matlab Simulink. Nucl. Eng. Des. 243, 360–370 (2012)

    Article  Google Scholar 

  12. 12.

    Zhang, D., Engeda, A., Hardin, J., Aungier, R.: Experimental study of steam turbine control valves. Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci. 218, 493–507 (2004)

    Article  Google Scholar 

  13. 13.

    Kostyuk, A., Kumenko, A., Nekrasov, A., Kalinin, S., Medvedev, S.: An experimental analysis of pressure pulsations in the steam admission elements of a turbine installation. Therm. Eng. 47, 529–537 (2000)

    Google Scholar 

  14. 14.

    Oberle, A.: Combined emergency stop and governor valve for controlling fluid flow to a turbo-machine, Patents US3809126A. https://patents.google.com/patent/US3809126 (1974)

  15. 15.

    Araki, T., Kuwashima, H.: Combined valve, Patents US4481776A. https://patents.google.com/patent/US4481776A/en (1984)

  16. 16.

    Gerdes, R., Padfield, R., Suter, F.: Valve arrangement for a power plant. Google Patents (2003)

  17. 17.

    Clark, R.B., Kure-Jensen, J., Miyayashiki, H., Ofuji, T.: Combined valve configuration for steam cycle units. New York, USA, Pat. US005870896A (1997)

  18. 18.

    Davis, D.H., Mossey, J.G.: Combined stop and intercept valve for steam turbines, Patents US4020869A. https://patents.google.com/patent/US4020869A/en (1977)

  19. 19.

    Zaryankin, A., Chernoshtan, V., Arianov, S., Noskov, V.: Some ways for improving vibration reliability of balanced control valves for steam turbines. Therm. Eng. 56, 644–648 (2009)

    Article  Google Scholar 

  20. 20.

    Steenburgh, J.H., Clark, R.B., Porteous, N.D.: Combined stop and control valve for supplying steam, Patents US6655409B1 (2003)

  21. 21.

    Yoo, Y.H., Suh, K.Y.: Engineering analysis of mass flow rate for turbine system control and design. Nucl. Eng. Des. 241, 4061–4078 (2011)

    Article  Google Scholar 

  22. 22.

    Bhowmik, P.K., Shamim, J.A., Suh, K.Y.: Flow characteristics analysis of control valve for turbine system. In: International Conference on Advances in Nuclear Power Plants (ICAPP), PI: 14359, Charlotte, NC, USA, 6–9 April 2014

  23. 23.

    Bhowmik, P., Shamim, J., Gairola, A., Arif, M., Suh, K.Y.: Numerical analysis of combined valve hydrodynamic characteristics for turbine system. In: Korean Nuclear Society Spring Meeting, Jeju, Korea, May 29–30, 2014

  24. 24.

    Halimi, B., Kim, S.H., Suh, K.Y.: Engineering of combined valve flow for power conversion system. Energy Convers. Manag. 65, 448–455 (2013)

    Article  Google Scholar 

  25. 25.

    Bhowmik, P., Shamim, J., Gairola, A., Suh, K.: Flow characteristics analysis of ultra supercritical overload turbine control valve for power plant. In: The 2nd IEEE Conference on Power Engineering and Renewable Energy (ICPERE) 2014. IEEE, pp. 85–90, Bali, Indonesia, 9–11 December 2014.

  26. 26.

    Zeß, J.-P., Polkas, T., Joos, F.: Experimental investigation of flow in a control valve of an industrial steam turbine. In: ASME Turbo Expo: Turbine Technical Conference and Exposition 2016, GT2016–57215, New York, NY (2016)

  27. 27.

    Kang, S.Y., Lee, J.J., Kim, T.S., Park, S.J., Hong, G.W., Ahn, J.H.: Program development for performance analysis of a steam turbine system with the use of overload valve. J. Mech. Sci. Technol. 30, 5759–5769 (2016)

    Article  Google Scholar 

  28. 28.

    Domnick, C.B., Brillert, D.: Flow-induced steam valve vibrations—A literature review of excitation mechanisms, preventive measures, and design improvements. ASME. J. Eng. Gas Turbines Power 141(5), 051009 (2018)

    Article  Google Scholar 

  29. 29.

    Kollross, P., Tajč, L.: AIP Conference Proceedings 2189, 020012 (2019); https://doi.org/10.1063/1.5138624

  30. 30.

    Slama, V., Mrozek, L., Tajc, L., Klimko, M., Zitek, P.: Flow analysis in a steam turbine control valve with through-flow valve chamber. ASME J Nucl. Radiat. Sci. 7(2), 021401 (2021). https://doi.org/10.1115/1.4049055

    Article  Google Scholar 

  31. 31.

    Hajsman, M., Kovandova, D., Matas, R.: Some aspects of numerical simulation of control valves for steam turbines. In: EPJ Web Conferences, vol. 25, p. 01052 (2012)

  32. 32.

    Amirante, R., Del Vescovo, G., Lippolis, A.: Evaluation of the flow forces on an open centre directional control valve by means of a computational fluid dynamic analysis. Energy Convers. Manag. 47, 1748–1760 (2006)

    Article  Google Scholar 

  33. 33.

    Song, X.G., Wang, L., Park, Y.C.: Fluid and structural analysis of a large diameter butterfly valve. J. Adv. Manuf. Syst. 8, 81–88 (2009)

    Article  Google Scholar 

  34. 34.

    Domnick, C.B., Benra, F.-K., Brillert, D., Dohmen, H.J., Musch, C.: Numerical investigation on the time-variant flow field and dynamic forces acting in steam turbine inlet valves. J. Eng. Gas Turbines Power 137(8), 081601 (2015)

    Article  Google Scholar 

  35. 35.

    Morita, R., Inada, F., Mori, M., Tezuka, K., Tsujimoto, Y.: CFD simulations and experiments of flow fluctuations around a steam control valve. J. Fluids Eng. 129, 48–54 (2007)

    Article  Google Scholar 

  36. 36.

    Lisowski, E., Filo, G.: CFD analysis of the characteristics of a proportional flow control valve with an innovative opening shape. Energy Convers. Manag. 123, 15–28 (2016)

    Article  Google Scholar 

  37. 37.

    Lisowski, E., Filo, G.: Analysis of a proportional control valve flow coefficient with the usage of a CFD method. Flow Meas. Instrum. 53, 269–278 (2017)

    Article  Google Scholar 

  38. 38.

    Wang, P., Liu, Y.Z.: Influence of a circular strainer on unsteady flow behavior in steam turbine control valves. Appl. Therm. Eng. 115, 463–476 (2017)

    Article  Google Scholar 

  39. 39.

    Wang, P., Ma, H., Quay, B., Santavicca, D.A., Liu, Y.Z.: Computational fluid dynamics of steam flow in a turbine control valve with a bell-shaped spindle. Appl. Therm. Eng. 129, 1333–1347 (2018)

    Article  Google Scholar 

  40. 40.

    Wang, P., Ma, H.Y., Liu, Y.Z.: Proper Orthogonal Decomposition and Extended-Proper Orthogonal Decomposition analysis of pressure fluctuations and vortex structures inside a steam turbine control valve. J. Eng. Gas Turbines Power 141(4), 41035 (2019)

    Article  Google Scholar 

  41. 41.

    Qian, J.Y., Hou, C.W., Mu, J., Gao, Z.X., Jin, Z.J.: Valve core shapes analysis on flux through control valves in nuclear power plants. Nucl. Eng. Technol. 52(10), 2173–2182 (2020)

    Article  Google Scholar 

  42. 42.

    Bhowmik, P.K., Shamim, J.A., Chen, X., Suh, K.Y.: Rod bundle thermal-hydraulics experiment with water and water-Al2O3 nanofluid for small modular reactor. Ann. Nucl. Energy 150, 107870 (2021)

    Article  Google Scholar 

  43. 43.

    Bhowmik, P.K., Schlegel, J.P., Kalra, V., Mills, C., Usman, S.: Design of condensation heat transfer experiment to evaluate scaling distortion in small modular reactor safety analysis. ASME J. Nucl. Eng. Radiat. Sci. 7, 031406 (2021)

    Article  Google Scholar 

  44. 44.

    ANSI/ ISA-75.02-1996: Control Valve Capacity Test Procedures. ISA (1996)

  45. 45.

    ANSI/ISA-75.01.01-2002. Flow Equations for Sizing Control Valves. ISA (2002)

  46. 46.

    STAR CCM+ (ver. 9.06.011), and Training Manual, version 05/14, CD-Adapco

  47. 47.

    CADCIM Technologies, Tickoo S, Raina V. CATIA V5R17 for designers

  48. 48.

    Barma, M.C., Saidur, R., Rahman, S.M.A., Allouhi, A., Akash, B.A., Sait, S.M.: A review on boilers energy use, energy savings, and emissions reductions. Renew. Sustain. Energy Rev. 79, 970–983 (2017)

    Article  Google Scholar 

  49. 49.

    Liu, X., Cui, J.: Economic model predictive control of boiler-turbine system. J. Process Control 66, 59–67 (2018)

    Article  Google Scholar 

  50. 50.

    AbouAl-Sood, M.M., Matrawy, K.K., Abdel-Rahim, Y.M.: Optimum parametric performance characterization of an irreversible gas turbine Brayton cycle. Int. J. Energy Environ. Eng. 4, 37 (2013). https://doi.org/10.1186/2251-6832-4-37

    Article  Google Scholar 

  51. 51.

    Mollenhauer, E., Christidis, A., Tsatsaronis, G.: Evaluation of an energy- and exergy-based generic modeling approach of combined heat and power plants. Int. J. Energy Environ. Eng. 7, 167–176 (2016). https://doi.org/10.1007/s40095-016-0204-6

    Article  Google Scholar 

  52. 52.

    Bhowmik, P.K., Dey, M.: Protection and control of steam turbine generator using PLC. In: First International Conference on Mechanical Engineering and Renewable Energy 2011 (ICMERE2011), Chittagong, Bangladesh, 22–24 December 2011

  53. 53.

    Bhowmik, P.K., Dhar, S.: Boiler gas burner management system automation using PLC. In: 2012 7th International Conference on Electrical and Computer Engineering, pp. 925–928. IEEE (2012)

  54. 54.

    Bloch, H., Singh, M.: Steam Turbines: Design, Applications and Re-Rating, 2nd edn. McGraw-Hill, New York (2008)

    Google Scholar 

  55. 55.

    Bhowmik, P.K, Dhar, S., Dey, M., Shamim, J.: Sizing and selection of control valve for process control loop. In: International Conference on Engineering Research, Innovation & Education (2013)

  56. 56.

    Bhowmik, P.K.: Sizing and selection of pressure relief safety valve. In: Proceedings of the 6th International Mechanical Engineering Conference & 14th Annual Paper Meet (6IMEC&14APM), 28–29 September 2012, Dhaka, Bangladesh (2012)

  57. 57.

    Anderson, J.D., Degrez, G., Dick, E., Grundmann, R.: Computational Fluid Dynamics: An Introduction. Springer, Berlin (2013)

    Google Scholar 

  58. 58.

    Mazur, Z., Urquiza, G., Campos, R.: Improvement of the turbine main stop valves with flow simulation in erosion by solid particle impact CFD. Int. J. Rotating Mach. 10, 747943–747952 (2004)

    Article  Google Scholar 

  59. 59.

    Ahmed, F., Ara, N., Deshpande, V., Mollah, A., Bhowmik, P.: CFD validation with optimized mesh using benchmarking data of pebble-bed high-temperature reactor. Prog. Nucl. Energy 134, 103653 (2021)

    Article  Google Scholar 

  60. 60.

    Hellström, F.: Numerical computations of the unsteady flow in turbochargers. Ph. D. thesis, Royal Institute of Technology, KTH (2010)

  61. 61.

    Dulau, M., Bica, D.: Mathematical modelling and simulation of the behaviour of the steam turbine. In: The 7th International Conference Interdisciplinarity in Engineering, INTER-ENG 2013, Elsevier, Procedia Technology, vol. 12, pp. 723–729 (2014)

  62. 62.

    Miller, N., Sanchez-Gasca, J., Price, W., Delmerico, R.: Dynamic modeling of GE 1.5 and 3.6 MW wind turbine-generators for stability simulations. In: 2003 IEEE Power Engineering Society General Meeting (IEEE Cat. No.03CH37491), Toronto, ON, Canada, vol. 3, pp. 1977–1983 (2003). https://doi.org/10.1109/PES.2003.1267470.

Download references

Acknowledgments

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIP) (No. 2008-0061900) and partly supported by the Brain Korea 21 Plus Project (No. 21A20130012821). Thanks to Joshua P. Schlegel, Associate Professor, Department of Nuclear Engineering and Radiation Science, Missouri University of Science and Technology, for the valuable review and comments.

Author information

Affiliations

Authors

Corresponding author

Correspondence to Palash K. Bhowmik.

Ethics declarations

Conflict of interest

On behalf of all authors, the corresponding author states that there is no conflict of interest.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Bhowmik, P.K., Suh, K.Y. Flow mapping using 3D full-scale CFD simulation and hydrodynamic experiments of an ultra-supercritical turbine’s combined valve for nuclear power plant. Int J Energy Environ Eng (2021). https://doi.org/10.1007/s40095-021-00394-0

Download citation

Keywords

  • Energy
  • Power
  • Conversion
  • Turbine
  • Valve
  • Experiment
  • CFD simulation