Design of a verticalaxis wind turbine: how the aspect ratio affects the turbine’s performance
 40k Downloads
 36 Citations
Abstract
This work analyses the link between the aspect ratio of a verticalaxis straightbladed (HRotor) wind turbine and its performance (power coefficient). The aspect ratio of this particular wind turbine is defined as the ratio between blade length and rotor radius. Since the aspect ratio variations of a verticalaxis wind turbine cause Reynolds number variations, any changes in the power coefficient can also be studied to derive how aspect ratio variations affect turbine performance. Using a calculation code based on the Multiple Stream Tube Model, symmetrical straightbladed wind turbine performance was evaluated as aspect ratio varied. This numerical analysis highlighted how turbine performance is strongly influenced by the Reynolds number of the rotor blade. From a geometrical point of view, as aspect ratio falls, the Reynolds number rises which improves wind turbine performance.
Keywords
VAWT MSTM HRotor Reynolds number Aspect ratioNomenclature
 a
Interference factor (–)
 V_{0}
Free stream wind speed (m/s)
 R
Rotor radius (m)
 ω
Rotor angular velocity (s^{−1})
 h
Blade length (m)
 w
Relative airfoil wind speed (m/s)
 α
Angle of attack (°)
 L
Lift (N)
 D
Drag (N)
 R*
Resultant force (N)
 ϑ
Blade angular position (°)
 P
Power (W)
 N_{b}
Number of blades (–)
 n
Rotor rotational velocity (rpm)
 Re
Reynolds number (–)
 ρ
Air density (kg/m^{3})
 ν
Kinematic air viscosity (m^{2}/s)
 c_{p}
Power coefficient (–)
 λ
Tip speed ratio (–)
 σ
Rotor solidity (–)
 σ_{cpmax}
σ that maximizes c_{ p } (–)
 λ_{cpmax}
λ that maximizes c_{ p } (–)
 c_{pmax}
Maximum c_{ p } (–)
 c
Airfoil chord (m)
 C_{L}
Lift coefficient (–)
 C_{D}
Drag coefficient (–)
Abbreviations
 NACA
National Advisory Committee for Aeronautics
 VAWT
Verticalaxis wind turbine
 HRotor
VAWT with straight blades
 TSR
Tip speed ratio
 MSTM
Multiple Stream Tube Model
 AR
Aspect ratio
Highlights

This paper evaluates VAWT performance;

How Reynolds number influences rotor performance has been studied;

How Reynolds number is linked to rotor aspect ratio has been investigated;

A new design procedure governing the rotor’s aspect ratio has been presented;

The new design procedure maximizes wind turbine efficiency.
Introduction
There are two types of wind turbine which produce electrical energy from the wind: they are horizontalaxis wind turbines (HAWTs) and verticalaxis wind turbines (VAWTs). The second, and in particular straightbladed VAWTs, have a simplified geometry with no yaw mechanism or pitch regulation, and have neither twisted nor tapered blades [1]. VAWTs may be utilized to generate electricity and pump water, as well as in many other applications [1]. Furthermore, they can handle the wind from any direction regardless of orientation and are inexpensive and quiet [2]. Wind turbines have aroused the interest of both industry and the academic community [3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 29, 30, 31], which have developed different numerical codes for designing and evaluating wind rotor performance. Recent studies [16, 17, 18, 19, 20] have highlighted that VAWTs can achieve significant improvements in efficiency.
VAWT can work even when the wind is very unstable making them suitable for urban and smallscale applications [21]. Their particular axial symmetry means they can obtain energy where there is high turbulence.
Their optimum operating conditions (maximum power coefficient) depend on rotor solidity and tip speed ratio [22]. For a VAWT rotor solidity depends on the number of blades, airfoil chord and rotor radius. Tip speed ratio is a function of angular velocity, undisturbed wind speed and rotor radius.
In the design process of a verticalaxis wind turbine it is crucial to maximize the aerodynamic performance [22, 26]. The aim is to maximize the annual energy production by optimizing the curve of the power coefficient varying with the tip speed ratio [25]. For a fixed crosssectional area of the turbine, to optimize the curve of the power coefficient it is possible to use different airfoil sections and/or rotors with different solidity [26].
To maximize energy extraction, other authors introduced guide vanes [27] and/or blade with a variable pitch angle [28] in verticalaxis wind turbines.
In the design process of a verticalaxis wind turbine, a wrong choice of the aspect ratio of the wind turbine may cause a low value of the power coefficient (wind turbine efficiency). This parameter (the aspect ratio) is often chosen empirically on the basis of the experience of the designer, and not on scientific considerations.
In this work, the link between the aspect ratio of a wind turbine and its performance has been studied, and a correlation between the aspect ratio and the turbine’s performance has been found.
Designing an HRotor
Figure 1 shows the behaviour of the power coefficient for a wind turbine with straight blades and a NACA 0018 airfoil.
Figure 1 curves were obtained using a calculation code based on MSTM theory [23].
From the graph in Fig. 1, the solidity which maximizes power coefficient σ = 0.3 can be identified, which has a c_{ pmax } = 0.51 corresponding to λ = 3.0.
(in Eq. 4 power P and wind velocity V_{ 0 } are design data and ρ is air volume mass).
This design approach is iterative and from time to time it will be necessary to reevaluate the blade’s Reynolds number and if necessary repeat the procedure with new power coefficient curves.
Adopting a mathematical approximation, to evaluate the Reynolds number, w can be substituted by ωR with the advantage of having a mean Reynolds number independent of the angle $\mathit{\vartheta}$ of rotation (see Fig. 2).
If the Reynolds number thus calculated is different to the one for the power coefficient curve adopted initially (Fig. 1), a new power coefficient curve should be plotted for a different Reynolds number (second attempt). Usually, the iterative design process needs only 2 or 3 iterations.
In conclusion, the Reynolds number strongly influences the power coefficient of a verticalaxis wind turbine. Furthermore, it changes as the main dimensions of the turbine rotor change. Increasing rotor diameter rises the Reynolds number of the blade.
The importance of aspect ratio
In Eq. 4 note how radius R increases as ratio AR decreases. In Eq. 2 if R increases, chord c increases too, and in Eq. 7 note how increasing the chord rises the Reynolds number. Finally, Fig. 3 shows how the power coefficient increases as the Reynolds number rises.
Equation (8) shows how ω is inversely proportional to R. From the Fig. 3 graph, note how λ_{cpmax} decreases as Reynolds number rises.
Application for a case study
To better explain the design procedure investigated in this work, a case study is presented. From Fig. 4, it is possible to notice that the lower the AR, the higher the Reynolds number; this can improve wind turbine performance. In the design procedure, a choice of a low value for the AR is therefore suitable. In this case study, a comparison between two wind rotors, designed with two different AR values (AR = 2 and AR = 0.4), will be presented.
VAWT––straight blade’s design procedure (h/R = 2)
Reference  1st attempt  2nd attempt  

Power (kW)  –  1  1 
Airfoil  –  NACA 0018  NACA 0018 
Wind speed (m/s)  –  10  10 
Air density (kg/m^{3})  –  1.2  1.2 
Kinematic air viscosity (m^{2}/s)  –  1.46 × 10^{−5}  1.46 × 10^{−5} 
Rotor aspect ratio (h/R)  –  2  2 
Number of blades (N_{ b })  –  2  2 
First attempt Reynolds  –  5 × 10^{6}  2.8 × 10^{5} 
c _{ pmax } ; σ _{ cpmax } ; λ _{ cpmax }  Fig. 3  0.51; 0.3; 3.0 (Fig. 3a)  0.464; 0.4; 2.96 (Fig. 3c) 
Rotor radius (m)  Eq. 3  0.904  0.947 
Airfoil Chord (m)  Eq. 4  0.136  0.189 
Rotational speed (rpm)  Eq. 6  317  299 
Second attempt Reynolds  Eq. 7  2.8 × 10^{5}  3.8 × 10^{5} 
Next step  –  Go to the 2° attempt  END 
VAWT––straight blade’s design procedure (h/R = 0.4)
Reference  1st attempt  2nd attempt  

Power (kW)  –  1  1 
Airfoil  –  NACA 0018  NACA 0018 
Wind speed (m/s)  –  10  10 
Air density (kg/m^{3})  –  1.2  1.2 
Kinematic air viscosity (m^{2}/s)  –  1.46 × 10^{−5}  1.46 × 10^{−5} 
Rotor aspect ratio (h/R)  –  0.4  0.4 
Number of blades (N_{ b })  –  2  2 
First attempt Reynolds  –  5 × 10^{6}  6.2 × 10^{5} 
c _{ pmax } ; σ _{ cpmax } ; λ _{ cpmax }  Fig. 3  0.51; 0.3; 3.0 (Fig. 3a)  0.475; 0.3; 3.01 (Fig. 3c) 
Rotor radius (m)  Eq. 3  2.021  2.094 
Airfoil Chord (m)  Eq. 4  0.303  0.314 
Rotational speed (rpm)  Eq. 6  142  137 
Second attempt Reynolds  Eq. 7  6.2 × 10^{5}  6.5 × 10^{5} 
Next step  –  Go to the 2° attempt  END 
Conclusion
This work looks at designing a verticalaxis wind turbine to maximize its power coefficient. It has been seen that the power coefficient of a wind turbine increases as the blade’s Reynolds number rises. Using a calculation code based on the Multiple Stream Tube Model, it was highlighted that the power coefficient is influenced by both rotor solidity and Reynolds number.
By analysing the factors which influence the Reynolds number, it was found that the ratio between blade height and rotor radius (aspect ratio) influences the Reynolds number and as a consequence the power coefficient.
It has been highlighted that a turbine with a lower aspect ratio has several advantages over one with a higher value.
The advantages of a turbine with a lower aspect ratio are: higher power coefficients, a structural advantage by having a thicker blade (less height and greater chord), greater inservice stability from the greater inertia moment of the turbine rotor.
References
 1.Islam, M., Ting, D.S.K., Fartaj, A.: Aerodynamic models for Darrieustype straightbladed vertical axis wind turbines. Renew. Sustain. Energy Rev. 12, 1087–1109 (2008)CrossRefGoogle Scholar
 2.Pope, K., Naterer, G.F., Dincer, I., Tsang, E.: Power correlation for vertical axis wind turbines with varying geometries. Int. J. Energy Res. 35, 423–435 (2011)CrossRefGoogle Scholar
 3.Eriksson, S., Bernhoff, H., Leijon, M.: Evaluation of different turbine concepts for wind power. Renew. Sustain. Energy Rev. 12, 1419–1434 (2008)CrossRefGoogle Scholar
 4.Riegler, H.: HAWT versus VAWT small VAWTs find a clear niche, pp. 44–46. Elsevier Refocus, New York (2003)Google Scholar
 5.Rohatgi, J., Barbezier, G.: Wind turbulence and atmospheric stability—their effect on wind turbine output. Renew. Energy 16, 908–911 (1999)CrossRefGoogle Scholar
 6.Castro, I.P., Cheng, H., Reynolds, R.: Turbulence over urbantype roughness: deductions from windtunnel measurements. Bound.Layer Meteorol. 118, 109–131 (2006)CrossRefGoogle Scholar
 7.Gayev, Y.A., Savory, E.: Influence of street obstructions on flow processes within urban canyons. J. Wind Eng. Ind. Aerodyn. 82, 89–103 (1999)CrossRefGoogle Scholar
 8.Akhmatov, V.: Influence of wind direction on intense power fluctuations in large offshore windfarms in the North Sea. Wind Eng. 31(1), 59–64 (2007)CrossRefGoogle Scholar
 9.Sahin, A.D., Dincer, I., Rosen, M.A.: Thermodynamic analysis of wind energy. Int. J. Energy Res. 30, 553–566 (2006)CrossRefGoogle Scholar
 10.Wright, A.K., Wood, D.H.: The starting and low wind speed behaviour of a small horizontal axis wind turbine. J. Wind Eng. Ind. Aerodyn. 92, 1265–1279 (2004)CrossRefGoogle Scholar
 11.Sahin, A.D., Dincer, I., Rosen, M.A.: Development of new spatiotemporal wind exergy maps. Proceedings of ASME2006 Mechanical Engineering Congress and Exposition, Chicago, IL, USA, 5–10 November 2006Google Scholar
 12.Center for Sustainable Energy: Ealing Urban Wind Study, Ealing Borough Council Urban Wind Study. The CREATE Centre, Bristol (2003)Google Scholar
 13.Biswas, A., Gupta, R., Sharma, K.K.: Experimental investigation of overlap and blockage effects on threebucket Savonius rotors. Wind Eng. 31(5), 313–368 (2007)CrossRefGoogle Scholar
 14.Bontempo, R., Manna, M.: Solution of the flow over a nonuniform heavily loaded ducted actuator disk. J. Fluid Mech. 728, 1469–7645 (2013)MathSciNetCrossRefGoogle Scholar
 15.Bontempo, R., Cardone, M., Manna, M., Vorraro, G.: Ducted propeller flow analysis by means of a generalized actuator disk model. Energy Procedia 45, 1107–1115 (2014)CrossRefGoogle Scholar
 16.Saha, U.: Optimum design configuration of Savonius rotor through wind tunnel experiments. J. Wind Eng. Ind. Aerodyn. 96(8), 1359–1375 (2008)CrossRefGoogle Scholar
 17.Hiraharaa, H., Hossainb, M.Z., Kawahashia, M., Nonomurac, Y.: Testing basic performance of a very small wind turbine designed for multipurposes. Renew. Energy 30, 1279–1297 (2005)CrossRefGoogle Scholar
 18.Wakui, T., Tanzawa, Y., Hashizume, T., Nagao, T.: Hybrid configuration of Darrieus and Savonius rotors for standalone wind turbinegenerator systems. Electr. Eng. Jpn. 150(4), 13–22 (2005)CrossRefGoogle Scholar
 19.Gupta, R., Biswas, A., Sharma, K.K.: Comparative study of a threebucket Savonius rotor with a combined threebucket Savonius––threebladed Darrieus rotor. Renew. Energy 33, 1974–1981 (2008)CrossRefGoogle Scholar
 20.Ale´, J.A.V., Petry, M.R., Garcia, S.B., Simioni, G.C.S., Konzen, G.: Performance evaluation of the next generation of small vertical axis wind turbine, European Wind Energy Conference and Exhibition, 7–10 May, Milano Convention Centre, Milan, Italy (2007)Google Scholar
 21.Armstrong, S., Fiedler, A., Tullis, S.: Flow separation on a high Reynolds number, high solidity vertical axis wind turbine with straight and canted blades and canted blades with fences. Renew. Energy 41, 13–22 (2012)CrossRefGoogle Scholar
 22.Paraschivoiu, I.: Wind Turbine Design with Emphasis on Darrieus Concept. Polytechnic International, Canada (2002)Google Scholar
 23.Strickland, J.H.: The Darrieus Turbine: A Performance Prediction Model Using Multiple Streamtubes, pp.1–36. SANDIA Report SAND750431, (1975)Google Scholar
 24.Robert, E., Sheldahl, Klimas P.C.: Aerodynamic characteristics of seven symmetrical airfoil sections through 180degree angle of attack for use in aerodynamic analysis of vertical axis wind turbines. Sandia National Laboratories. Report SAND802114. 1981 (1980)Google Scholar
 25.Bhutta, M.M.A., Hayat, N., Farooq, A.U., Ali, Z., Jamil, ShR, Hussain, Z.: Vertical axis wind turbine––a review of various configurations and design techniques. Renew. Sustain. Energy Rev. 16, 1926–1939 (2012)CrossRefGoogle Scholar
 26.Hameed, M.S., Afaq, S.K.: Design and analysis of a straight bladed vertical axis wind turbine blade using analytical and numerical techniques. Ocean Eng. 57, 248–255 (2013)CrossRefGoogle Scholar
 27.Chong, W.T., Fazlizan, A., Poh, S.C., Pan, K.C., Hew, W.P., Hsiao, F.B.: The design, simulation and testing of an urban vertical axis wind turbine with the omnidirectionguidevane. Appl. Energy 112, 601–609 (2013)CrossRefGoogle Scholar
 28.Cooper, P., Kennedy, O.C.: Development and analysis of a novel vertical axis wind turbine. Proceedings Solar 2004––Life, The Universe and Renewables 1–9 (2004)Google Scholar
 29.Ajayi, O., Fagbenle, R., Katende, J., Aasa, S.A., Okeniyi, J.: Wind profile characteristics and turbine performance analysis in Kano, northwestern Nigeria. Int. J. Energy Environ. Eng. 4, 27 (2013)CrossRefGoogle Scholar
 30.Morshed, K., Rahman, M., Molina, G., Ahmed, M.: Wind tunnel testing and numerical simulation on aerodynamic performance of a threebladed Savonius wind turbine. Int. J. Energy Environ. Eng. 4, 18 (2013)CrossRefGoogle Scholar
 31.Liu, S., Janajreh, I.: Development and application of an improved blade element momentum method model on horizontal axis wind turbines. Int. J. Energy Environ. Eng. 3, 30 (2012)CrossRefGoogle Scholar
Copyright information
This article is published under license to BioMed Central Ltd. Open AccessThis article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited.