Abstract
In this paper, theoretical model for calculating halo current has been developed. This work attained novelty as no theoretical calculations for halo current has been reported so far. This is the first time to use theoretical approach. The research started by calculating points for plasma energy in terms of poloidal and toroidal magnetic field orientations. While calculating these points, it was extended to calculate halo current and to developed theoretical model. Two cases were considered for analyzing the plasma energy when flows down/upward to the diverter. Poloidal as well as toroidal movement of plasma energy was investigated and mathematical formulations were designed as well. Two conducting points with respect to (R, Z) were calculated for halo current calculations and derivations. However, at first, halo current was established on the outer plate in clockwise direction. The maximum generation of halo current was estimated to be about 0.4 times of the plasma current. A Matlab program has been developed to calculate halo current and plasma energy calculation points. The main objective of the research was to establish theoretical relation with experimental results so as to precautionary evaluate the plasma behavior in any Tokamak.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
During the disruption scenario in plasma, eddy and halo currents were considered to be the most important sources that came out as a result of this phenomenon [1]. The components which affect primarily are diverter, First Wal (FW) and other main components, because plasma is unstable in vertical displacement. In this scenario, plasma moved upward and downward resulting into plasma disruption, and as a result, halo current has been generated helically. This halo current was produced in SOL component and flows into the vacuum vessel through in-vessel components that may give rise to large force acting on the vessel and in-vessel components [2]. The number of research articles has been published to investigate the halo current in other Tokamak devices such as JET [3], JT-60U [4], and NSTX [5]. Like in Experimental Advanced Superconducting Tokamak (EAST) reactor [6,7,8], there are some failures of the feedback control in VD event caused by disruption. The EAST reactor is designed by Institute of Plasma Physics, Chinese Academy of Sciences, P.R. China which is considered to be the best superconducting and advanced Tokamak in the world.
Recently, EAST has been updated and had achieved longer pulse generations at high current mode. Main parameters of EAST reactor are given in Table 1 [9].
The EAST has been demonstrated as long-pulsed plasma operations with toroidal field Bt ≤ 3.5 T and plasma current Ip ≤ 1 MA [10,11,12]. The EAST upper diverter has been upgraded with W/Cu plasma facing components (PFCs) with ITER like W-monoblack [13]. The lower diverter has not been upgraded using graphite tiles for the first wall. It has a central dome, but the upper diverter does not equip with it. In addition, an EAST disruption database has been built [14] and is useful for quickly selecting disruptive discharges and their relevant parameters. Nearly, 27% of discharges terminated in a disruption [15].
In this reactor, some sensors have been installed for calculating the halo currents at different locations, as given in Table 2. In these experiments, it was observed that the halo current first spread out on outer baffle plate then moves to dome and finally return back to plasma. At first, we have developed model (2) to calculate magnetic field produced by circular current loop. Furthermore, we considered two cases to analyze the plasma when it flows up/down direction as observed by model (2) calculation data. Second, we have theoretically calculated horizontal/vertical forces connected with model (2). It was observed that generation of halo current was huge and it has strong field at the middle and weak or cancelling effects appear at the sideways positions. Third, during disruption, magnetic field appears at the conducting points consisting of large number of magnetic flux. Therefore, halo current model (18) has been developed using Eqs. (9 and 15) with specific parameters (rp, z, zp, ushift, \(\phi\)). A Matlab program has been developed to calculate halo current and magnetic field calculation points. The achievable maximum halo current was about 0.4 times of the plasma current and its maximum TPF values was 0.65 as estimated by set of sensors. EAST halo current is 10 KA for one cassette and total estimation is 400 KA by model (18).
Some of the work that has already been published for halo current is given as under
-
Strauss with his team carried out heavy simulation using M3D code for calculating the halo current and plasma disruption conditions [16].
-
Long et al. experimentally calculated the values of eddy and halo current in EAST reactor while conducting set of VDE experiments [17].
-
Other impressive contributions by Strauss and his team for assessing and simulation of halo current in ITER through VDE instabilities and developed 3D models for plasma disruption conditions [18].
-
Fantechi and Crutzen modeled the plasma FW contact under vertical instabilities with a 3D eddy current simulation. The simulation worked for transferring the electric current (halo current) to FW component through VDE [19].
Model of magnetic field calculation points for Tokamak
In this research work, a new model for calculating different aspects of Tokamak reactor has been designed. In the recent past, number of work has been published already about the shaping and geometrical description of plasma [20, 21]. One of the important problem is to identify and simulate the plasma shape and control including the numerical calculations on elongated and shaped equilibria [22]. In this paper, a new model was developed on the basis of an applied mathematical approach [23], that is
where “k” is elongation, “δ” is triangularity, “a” is minor radius, and “R ”0 is the major radius. Using the algebraic techniques, as the magnetic field is B = BX + BY, we obtained Bx and Bz using shape model (1) in energy integral [24]. The calculated points are given as under
Magnetic field produced by a circular current loop [25] is
where R0 = 1.7 –1.8, B0 = 3.5T, plasma current Ip ≤ 1 MA.
Plasma orientation and development of halo current
In case of plasma, it was observed that some balancing and unbalancing forces acted upon, like the case of plasma as torus which is very close to outboard wall. At this stage, poloidal field has different radial locations and have variable sideways forces as well. In this case, one side of torus has higher values than other side and poloidal field has different values at different locations.
Case 1
In this case, we considered the plasma at a position (R, Z) from the origin and assumed that during the disruption occurs (Fig. 1), the plasma moves horizontally [26, 27]. The governing equations are given as under
Since
where
Therefore
Since the plasma is in the range of 0 → 2π, therefore
Substitution of Eqs. (2) into (9) gives the changes in magnetic field while applying the horizontal forces on the plasma giving plasma position in different points, as presented in Table 3. For static position, each cross section depends on a, b, r, and z. For one cross section, the peak values of r and z are (± 5.2, ± 4.37); therefore, (Br(max,up), Br(max,down)) = (0.3918, − 0.3847). Then, the current loop of magnetic field range was (Bx, Bz)max = (0.3862, 0.1698) for selected degree of cos (alpha) and plasma one cross-sectional area energy was calculated to be 8.0262e + 004. For tilting position, peak values of r and z were (± 5.4, ± 4.17); therefore, (Br(max,up), Br(max,down)) = (0.4225, − 0.4247). Hence, the current loop of magnetic field range was (Bx, Bz)max = (0.4221, 0.1974) for selected degree of cos(alpha) and calculated plasma one cross-sectional area energy was 8.0258e + 004 (see Table 3).
Case 2
In this case, we considered plasma at a position (R, Z) from the origin and assumed that during disruption occurs (Fig. 2), plasma moves vertically downward [26, 27]. The governing equations are given as under
Then
Since
Where
Therefore
Since the plasma is in the range of 0 → 2π:
and
Changes in magnetic field can be described by substituting Eq. (2) into Eq. (15) to get the vertical forces applies to the plasma so as to calculates the plasma position at different points. Like in Case-1, each cross section depended upon a, b, r, and z. For one cross section, the peak values of r, z were (± 3.5, ± 2.3); therefore, (Br(max,up), Br(max,down)) = (0.1865, −0.4652). Then, the current loop of magnetic field range was (Bx, Bz)max = (0.4637, 0.1995) for selected degree of cos(alpha) and plasma one cross-sectional area energy was 8.0457e + 004. For tilting position, peak values of r and z were (± 3.8, ± 2.5); therefore, (Br(max,up), Br(max,down)) = (0.2762, − 0.3851). The current loop of magnetic field range was (Bx, Bz)max = (0.5747, 0.2525) for selected degree of cos(alpha) and the calculated values of plasma one cross-sectional area energy was 8.0484e + 004 (see Table 4).
During VDE, plasma changes the area under vertical and horizontal forces and the magnetic field changes in radial direction at center of plasma with major radius (R), x–z displacement and plasma radial/vertical length (zp, rp). During this plasma change, magnetic field of each point can be calculated by model (2) (vertical and horizontal). The magnetic field appears at the conducting points consisting of large number of magnetic flux, which are given below as
At the conducting points, generation of halo current was huge and it has strong field at the middle and weak forces or cancelling effects appeared at the sideways positions. Due to horizontal and vertical forces, some balancing and unbalancing forces appeared and it was expected that asymmetric plasma positions were along the toroidal coordinates. The poloidal halo current which balances the plasma vertical displacement was toroidally asymmetric. According to the plasma positions, these halo currents have different flow poloidal paths along with the toroidal coordinates. Similarly, due to the asymmetry of poloidal halo currents, the second sideways force occured and the sum of these forces gave sideways balancing forces as well:
The total forces includes horizontal and vertical and the summation of these forces acted upon the plasma VDE direction gives halo current as given below:
During the course of disruption, halo and eddy currents considered to be the main source of electro-mechanical loads that appeared. Consequently, halo current fraction and toroidal peaking factor (TPF) in vessel components depend upon the halo current density. In MHD simulation problems, plasma model comprises of three regions, namely, core, halo, and resistive wall region integrating plasma to external vacuum magnetic field. In EAST reactor, plasma was inherently unstable against vertical displacement and during upward and downward movement creates disruption along with large halo current generation. In this case, when the plasma flows into the vacuum vessel through in-vessel components, halo current produced large values of J × B forces acting on the vessel through in-vessel components. The production and movement of halo current is such that it first appeared on the outer plate in clockwise direction and maximum generation of halo current was estimated to be about 0.4 times of the plasma current. Figure 3 shows the evolution of halo current and filament. EAST halo current is 10 KA for one cassette and total 400KA recorded by model (18). In EAST, Rogowski coils have been designed for both the upper and lower diverters to measure the disruption of halo currents. EAST upper diverter was upgraded with a new tungsten diverter consisting of 80 cassettes in the toroidal direction. Four upper diverter, cassettes have been instrumented with a set of 10 small-cross sections. Rogowski coils to determine where the halo currents enter and exit the diverter, and how much current flows through the water cooling tubes. In this paper, we have successfully performed theoretical investigation between halo current-plasma deformation/displacement and theoretical calculation of total halo currents as well.
Conclusion
The developed theoretical model calculates plasma cross sections by Bx and Bz magnetic field points and displacement subjected to the start of VDE and magnetic field flux variations. The developed two conducting points give an indication to halo current percentages as well. This model can calculate theoretically halo current during the disruption phases in a very short time. Furthermore, mathematical techniques have been developed successfully which shows the relation between halo currents and plasma displacement/deformation in EAST Tokamak. Computational program has been developed to calculate total halo current and magnetic field calculation points. Theoretical investigation of each cassette has been calculated by model. This model can be subjected to experimental data for other Tokamak devices as well.
Abbreviations
- A (m2):
-
Plasma area
- \(a^{\prime}\) (m):
-
Minor radius
- a (m):
-
Radius of current loop
- A p :
-
Median flow path length
- A :
-
Indicates the Plasma tilt positions
- B 0 (T):
-
Initial magnetic field
- B x (T):
-
Magnetic field in x-direction
- B z (T):
-
Magnetic field in z-direction
- B θ (T):
-
Poloidal magnetic field
- B (T):
-
Magnetic field
- b (m):
-
z-axis coordinate of current loop
- B tor (T):
-
Toroidal magnetic field
- E (k):
-
Second type of elliptic integral
- I p (MA):
-
Total plasma toroidal current
- K (m):
-
Elongation
- K (k):
-
First type of elliptic integral
- \(R^{\prime}\) (m):
-
Major radius
- r p (m):
-
Plasma radial length
- δr p :
-
Radial kink mode amplitude
- Z :
-
z-axis coordinate of calculated point
- Δ:
-
Triangularity
- \(\phi\) :
-
Magnetic flux
- δz p :
-
Vertical kink mode amplitude
- z p (m):
-
Plasma vertical length
References
Riccardo, V., et al.: Progress in understanding halo current as JET. Nucl. Fusion 49, 8 (2012)
ITER Physics Expert Group on Disruptions: Plasma Control, MHD and ITER Physics Basis Editors. Nucl. Fusion 49, 8 (1999)
Riccardo, V., Walkerb, S., Nollc, P.: Modelling magnetic forces during asymmetric vertical displacement events in JET. Fusion Eng. Des. 47(4), 389–402 (2000)
Neyatani, Y., Yoshino, R., Nakamura, Y., Sakurai, S.: Characteristics of halo currents in JT-60U. Nucl. Fusion 39(4), 559 (1999)
Gerhardt, S.P.: Dynamics of the disruption halo current toroidal asymmetry in NSTX. Nucl. Fusion 53, 023005 (2013)
Normile, D.: Waiting for ITER. Fusion jocks look EAST. Science. 312, 992–993 (2006)
Wan, B.N.: Recent experiments in the EAST and HT-7 superconducting Tokamaks. Nucl. Fusion 49, 104011 (2009)
Li, J., Wan, B.N.: Recent progress in RF heating and long-pulse experiments on EAST. Nucl. Fusion 51, 094007 (2011)
Wang, X., et al.: Progress of high power and long pulse ECRH system in EAST. Fusion Eng. Des. 96–97, 181–186 (2015)
Wan, B., for the EAST andHT-7 Teams and International Collaborators: Recent experiments in the EAST and HT-7 superconducting tokamaks. Nucl. Fusion 49, 104011 (2009)
Wan, Y.X., Li, L., Weng, P., and EAST team.: Overview progress and future plan of the east project. In: OV/1-1 on 21th IAEA Fusion Energy Conference. Chengdu. China. (2006)
Li, J., et al.: A long-pulse high-confinement plasma regime in the Experimental Advanced Superconducting Tokamak. Nat. Phys. 9. 817. 2013
Li, J., et al.: Plasma facing components for the Experimental Advanced Superconducting Tokamak and CFETR. Phys. Scr. T159, 014001 (2014)
Granetz, R.S., et al.: 7th US-PRC Magnetic Fusion Collaboration Workshop. 28. http://www.swip.ac.cn/mfcw2014/7th%20US-PRC%20MFC%20abstracts.pdf#page=29.2014
Long, C.D., et al.: Characterization of plasma current quench during disruption in EAST tokamak. Chin. Phys. B 24, 025205 (2015)
Strauss, H.R. et al.: Halo current and resistive wall simulations of ITER. 1-7.TH/2-2
Long, C.D. et al.: Observation and analysis of halo current in EAST. Chin Phys B. 23, 065205 (2014)
Strauss, H.R.: Non-linear MHD halo current simulations, TH/2-3
Fabtechi, S., Crutzen, Y.: Modelling and analysis of plasma-first wall contact during vertical instabilities in next-step tokamaks with a 3D eddy current code. In: Fusion Technology 1996. Proceedings of the 19th Symposium on Fusion Technology, Lisbon, Portugal, 16–20 September 1996, pp. 727–730. Elsevier, Amsterdam (1997)
Long, C.D., et al.: Halo current diagnostic system of experimental advanced superconducting tokamak. Rev. Sci. Instrum. 86, 103506 (2015)
Pironti, A., et al.: Optimal choice of the geometrical descriptors for tokamak plasma shape control. Fusion Eng. Des. 43, 115–127 (1998)
Kurihara, K.: A new shape reproduction method based on the Cauchy-condition surface for real-time Tokamak reactor control. Fusion Eng. Des. 51–52, 1049–1057 (2000)
Hofinann, F., et al.: Equilibrium and axisymmetric stability of the proposed TCV Tokamak. 14th Symposium on Fusion Technology. Fusion Technol. 1, 687–692 (1986)
Wesson, J.: Tokamaks. Oxford Univ Press, Oxford (2011)
Yuntao, S., Wu, W., Du, S.: Tokamak engineering mechanics. Mechanical Engineering Series. Springer, Berlin (2014). ISBN: 978-3-642-39574-1
Bachmann, C.: Asymmetric forces on the ITER plasma in kink mode in subsequent halo currents in the VV. ITER_D_28P25D v1.0. (2015)
Forces on the ITER Vacuum Vessel due to the Plasma in Kink Mode during a VDEIII with Slow Current Quench, ITER_D_26RLC9
Acknowledgements
The authors would like to sincerely appreciate the Deanship of Scientific Research at King Saud University for its funding of this research through the Research Group Project No. RGP-255.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Khan, S.UD., Khan, S.UD., Song, Y. et al. Theoretical relation between halo current-plasma energy displacement/deformation in EAST. J Theor Appl Phys 12, 23–31 (2018). https://doi.org/10.1007/s40094-018-0276-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40094-018-0276-1