Advertisement

Metallography, Microstructure, and Analysis

, Volume 6, Issue 6, pp 463–469 | Cite as

Die and Process Parameters Effects on ECAP Process of Sheet-Type Samples

  • P. M. Keshtiban
  • F. Bashirzadeh
Technical Article

Abstract

Severe plastic deformation methods are the main top-down approaches for applying mechanical deformation on the material in which equal channel angular pressing (ECAP) is the most favorite one. In the presented study, ECAP process of a sheet-type samples were investigated by both FEM and experimental works. Firstly, evaluation of FE simulation was done using both practical works and theoretical equations. Then, the results of suggested Taguchi simulations were used to determine the relations between inputs and outputs by regression analysis. Afterward, the influences of input parameters on outputs were obtained by ANOVA. Finally, the microstructure evolutions of samples were discussed using metallographic techniques. It was inferred that after ECAP, the average grain size was reduced to smaller than the half value.

Keywords

SPD ECAP Regression ANOVA Sheet 

References

  1. 1.
    L. Ghalandari, M. Moshksar, High-strength and high-conductive Cu/Ag multilayer produced by ARB. J. Alloy. Compd. 506(1), 172–178 (2010)CrossRefGoogle Scholar
  2. 2.
    N. Takata, S.-H. Lee, N. Tsuji, Ultrafine grained copper alloy sheets having both high strength and high electric conductivity. Mater. Lett. 63(21), 1757–1760 (2009)CrossRefGoogle Scholar
  3. 3.
    K.X. Wei, W. Wei, F. Wang, Q.B. Du, I.V. Alexandrov, J. Hu, Microstructure, mechanical properties and electrical conductivity of industrial Cu–0.5% Cr alloy processed by severe plastic deformation. Mater. Sci. Eng. A 528(3), 1478–1484 (2011)CrossRefGoogle Scholar
  4. 4.
    R.Z. Valiev, T.G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement. Prog. Mater. Sci. 51(7), 881–981 (2006)CrossRefGoogle Scholar
  5. 5.
    T.G. Langdon, The principles of grain refinement in equal-channel angular pressing. Mater. Sci. Eng. A 462(1), 3–11 (2007)CrossRefGoogle Scholar
  6. 6.
    K. Abrinia, S. Orangi, Investigation of process parameters for the backward extrusion of arbitrary-shaped tubes from round billets using finite element analysis. J. Mater. Eng. Perform. 18(9), 1201 (2009)CrossRefGoogle Scholar
  7. 7.
    G. Faraji, M.M. Mashhadi, H.S. Kim, Tubular channel angular pressing (TCAP) as a novel severe plastic deformation method for cylindrical tubes. Mater. Lett. 65(19), 3009–3012 (2011)CrossRefGoogle Scholar
  8. 8.
    P. Keshtiban, M. Zadshakouyan, G. Faraji, Friction study in equal channel multi angular pressing: load curve and ring compression tests. Trans. Indian Inst. Met. 69(9), 1793–1800 (2016)CrossRefGoogle Scholar
  9. 9.
    A. Farhoumand, R. Ebrahimi, Analysis of forward–backward-radial extrusion process. Mater. Des. 30(6), 2152–2157 (2009)CrossRefGoogle Scholar
  10. 10.
    W. Bae, D. Yang, An upper-bound analysis of the backward extrusion of tubes of complicated internal shapes from round billets. J. Mater. Process. Technol. 36(2), 157–173 (1993)CrossRefGoogle Scholar
  11. 11.
    N. Thangapandian, S.B. Prabu, K. Padmanabhan, Effects of die profile on grain refinement in Al–Mg alloy processed by repetitive corrugation and straightening. Mater. Sci. Eng. A 649, 229–238 (2016)CrossRefGoogle Scholar
  12. 12.
    N. Pardis, B. Talebanpour, R. Ebrahimi, S. Zomorodian, Cyclic expansion-extrusion (CEE): a modified counterpart of cyclic extrusion-compression (CEC). Mater. Sci. Eng. A 528(25), 7537–7540 (2011)CrossRefGoogle Scholar
  13. 13.
    V.P. Basavaraj, U. Chakkingal, T.P. Kumar, Study of channel angle influence on material flow and strain inhomogeneity in equal channel angular pressing using 3D finite element simulation. J. Mater. Process. Technol. 209(1), 89–95 (2009)CrossRefGoogle Scholar
  14. 14.
    H.S. Kim, M.H. Seo, S.I. Hong, Plastic deformation analysis of metals during equal channel angular pressing. J. Mater. Process. Technol. 113(1), 622–626 (2001)CrossRefGoogle Scholar
  15. 15.
    G. Zhao, Sh Xu, Y. Luan, Y. Guan, N. Lun, X. Ren, Grain refinement mechanism analysis and experimental investigation of equal channel angular pressing for producing pure aluminum ultra-fine grained materials. Mater. Sci. Eng. A 437(2), 281–292 (2006)CrossRefGoogle Scholar
  16. 16.
    I. Gutierrez-Urrutia, M. Munoz-Morris, D.G. Morris, Contribution of microstructural parameters to strengthening in an ultrafine-grained Al–7% Si alloy processed by severe deformation. Acta Mater. 55(4), 1319–1330 (2007)CrossRefGoogle Scholar
  17. 17.
    P.M. Keshtiban, M. Zadshakouyan, G. Faraji, Optimization of ECMAP parameters in production of ultra-fine grained Al1050 strips using grey relational analysis. J. Adv. Mater. Process. 3(4), 33–48 (2015)Google Scholar

Copyright information

© Springer Science+Business Media, LLC and ASM International 2017

Authors and Affiliations

  1. 1.Faculty of Mechanical EngineeringUrmia University of TechnologyUrmiaIran
  2. 2.Faculty of Materials EngineeringSahand University of TechnologyTabrizIran

Personalised recommendations