Skip to main content
Log in

The Experimental Assessment of Deformation and Springback Behavior for Additive Manufactured Ti6Al4V

  • Research Article-Mechanical Engineering
  • Published:
Arabian Journal for Science and Engineering Aims and scope Submit manuscript


In this study, heat treatment was applied to Ti6Al4V materials produced by the selective laser melting (SLM) method at 550 ℃, 800 ℃, 950 ℃, and 1080 ℃ temperatures, and the effect of this process on microstructure and mechanical properties was also investigated. Moreover, the parts produced with the additive manufacturing technique can be exposed to many loads at the place of use. Therefore, to determine the resistance of the materials against bending, the V bending process was applied to the materials in 6-, 7.5-, and 9-degree dies. XRD and SEM investigated the microstructure and optical microscope changes, and the mechanical properties were examined by uniaxial tensile test and microhardness analysis. In the test samples, pore and unmelted powder particles due to production in the microstructure were observed, and it was observed that the grain sizes increased with the increase in the heat treatment temperature. It was observed that samples HT550, HT800, and HT950 were shaped without breaking in the bending process in the 6-degree die, and all the samples were broken in the experiments performed in the 7.5- and 9-degree die.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Subscribe and save

Springer+ Basic
EUR 32.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or Ebook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

Similar content being viewed by others


  1. Somashekara, M.A.; Suryakumar, S.: Studies on dissimilar twin-wire weld-deposition for additive manufacturing applications. Trans Indian Inst. Met. 70(8), 2123–2135 (2017)

    Article  Google Scholar 

  2. Ge, J.; Lin, J.; Lei, Y.; Fu, H.: Location-related thermal history, microstructure, and mechanical properties of arc additively manufactured 2Cr13 steel using cold metal transfer welding. Mater. Sci. Eng. A 715(2018), 144–153 (2018)

    Article  Google Scholar 

  3. Fang, X.; Zhang, L.; Li, H.; Li, C.; Huang, K.; Lu, B.: Microstructure evolution and mechanical behavior of 2219 aluminum alloys additively fabricated by the cold metal transfer process. Materials 11(2018), 812–824 (2018)

    Article  Google Scholar 

  4. Liberini, M., Astarita, A., Campatelli, G., Scippa, A., Montevecchi, F., Venturini, G., Durante, M., Boccarusso, L., Memola, F., Minutolo, C., Squillace, A. (2017) Selection of optimal process parameters for wire arc additive manufacturing. In: 10th CIRP Conference on Intelligent Computation in Manufacturing Engineering—CIRP ICME '16, pp. 470–474, 20-22 July 2016, Ischia, Italy

  5. Ding, D.; Pan, Z.S.; Cuiuri, D.; Li, H.: A tool-path generation strategy for wire and arc additive manufacturing. Int. J. Adv. Manuf. Technol. 73(2014), 173–183 (2014)

    Article  Google Scholar 

  6. Emre, H.E.: The corrosion behaviour of as-welded and post-weld heat treated Ti6Al4V alloy in simulated body fluid. Mater. Lett. 254, 162–166 (2019)

    Article  Google Scholar 

  7. Popovich, A., Sufiiarov, V., Borisov, E., Polozov, I. A.: Microstructure and mechanical properties of Ti–6Al–4V manufactured by SLM. In: Key Engineering Materials, vol. 651, pp. 677–682. Trans Tech Publications Ltd (2015)

  8. Wauthle, R.; Vrancken, B.; Beynaerts, B.; Jorissen, K.; Schrooten, J.; Kruth, J.P.; Van Humbeeck, J.: Effects of build orientation and heat treatment on the microstructure and mechanical properties of selective laser melted Ti6Al4V lattice structures. Addit. Manuf. 5, 77–84 (2015)

    Google Scholar 

  9. Khorasani, A.; Gibson, I.; Goldberg, M.; Littlefair, G.: On the role of different annealing heat treatments on mechanical properties and microstructure of selective laser melted and conventional wrought Ti–6Al–4V. Rapid Prototyp. J. 23(2), 295–304 (2017)

    Article  Google Scholar 

  10. Losertová, M., Kubeš, V.: Microstructure and mechanical properties of selective laser melted Ti6Al4V alloy. In: IOP Conference Series: Materials Science and Engineering, vol. 266, no. 1, p. 012009. IOP Publishing (2017, November)

  11. Do, D.K.; Li, P.: The effect of laser energy input on the microstructure, physical and mechanical properties of Ti–6Al–4V alloys by selective laser melting. Virtual Phys. Prototyp. 11(1), 41–47 (2016)

    Article  Google Scholar 

  12. Vrancken, B.; Thijs, L.; Kruth, J.P.; Van Humbeeck, J.: Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties. J. Alloy. Compd. 541, 177–185 (2012)

    Article  Google Scholar 

  13. Wu, S.Q.; Lu, Y.J.; Gan, Y.L.; Huang, T.T.; Zhao, C.Q.; Lin, J.J., et al.: Microstructural evolution and microhardness of a selective-laser-melted Ti–6Al–4V alloy after post heat treatments. J. Alloy. Compd. 672, 643–652 (2016)

    Article  Google Scholar 

  14. Nicoletto, G.; Maisano, S.; Antolotti, M.; Dal’lAglio, F.: Influence of post fabrication heat treatments on the fatigue behavior of Ti–6Al–4V produced by selective laser melting. Procedia Struct. Integr. 7, 133–140 (2017)

    Article  Google Scholar 

  15. Zhou, B.; Zhou, J.; Li, H.; Lin, F.: A study of the microstructures and mechanical properties of Ti6Al4V fabricated by SLM under vacuum. Mater. Sci. Eng. A 724, 1–10 (2018)

    Article  Google Scholar 

  16. Yan, X.; Yin, S.; Chen, C.; Huang, C.; Bolot, R.; Lupoi, R., et al.: Effect of heat treatment on the phase transformation and mechanical properties of Ti6Al4V fabricated by selective laser melting. J. Alloy. Compd. 764, 1056–1071 (2018)

    Article  Google Scholar 

  17. International Handbook Committee, A.: Volume 14: Forming and Forging (1993)

  18. Huang, Q.; Liu, X.; Yang, X.; Zhang, R.; Shen, Z.; Feng, Q.: Specific heat treatment of selective laser melted Ti–6Al–4V for biomedical applications. Front. Mater. Sci. 9(4), 373–381 (2015)

    Article  Google Scholar 

  19. Balcı, A.; Küçükaltun, F.; Aycan, M.F.; Usta, Y.; Demir, T.: Reproducibility of replicated trabecular bone structures from ti6al4v extralow interstitials powder by selective laser melting. Arab. J. Sci. Eng. 46(3), 2527–2541 (2021)

    Article  Google Scholar 

  20. Sun, Y.Y.; Wang, P.; Lu, S.L.; Li, L.Q.; Nai, M.L.S.; Wei, J.: Laser welding of electron beam melted Ti–6Al–4V to wrought Ti–6Al–4V: effect of welding angle on microstructure and mechanical properties. J. Alloy. Compd. 2019(782), 967–972 (2019)

    Article  Google Scholar 

  21. Kale, A.B.; Alluri, P.; Singh, A.K.; Choi, S.H.: The deformation and fracture behavior of 316L SS fabricated by SLM under mini V-bending test. Int. J. Mech. Sci. 196, 106292 (2021)

    Article  Google Scholar 

  22. Aydin, K.; Karaağaç, İ: The experimental investigation of formability and spring-back in laser welded DP600 sheets. Mater. Res. Express 6(12), 1265a8 (2019)

    Article  Google Scholar 

  23. Aydın, K.; Karaağaç, İ; Uluer, O.: The formability and spring-back characterization of laser-welded DP–HSLA sheets. Appl. Phys. A 125(8), 1–10 (2019)

    Article  Google Scholar 

Download references


This article was supported by the Manisa Celal Bayar University Scientific Research Projects Coordination Unit (Project number 2020/47).

Author information

Authors and Affiliations


Corresponding author

Correspondence to Kadir Aydın.

Ethics declarations

Conflict of interest

The authors declare no competing interests.

Ethical Approval

Not applicable.

Consent to Participate

The authors accept to participate.

Consent for publication

The authors agree with the publication.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Aydın, K., Karamolla, M., Karaağaç, İ. et al. The Experimental Assessment of Deformation and Springback Behavior for Additive Manufactured Ti6Al4V. Arab J Sci Eng 48, 11773–11780 (2023).

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: