Skip to main content
SpringerLink
Log in

Establishing Correlation Between Current and Voltage Signatures of the Arc and Weld Defects in GMAW Process

  • Research Article - Mechanical Engineering
  • Published:
Arabian Journal for Science and Engineering Aims and scope Submit manuscript

Abstract

Welding is one of the major metal-joining process employed in fabrication industries, especially in manufacturing of boilers and pressure vessels. Control of weld quality is very important for such industries considering the severe operating conditions. Industries are looking for some kind of real-time process monitoring/control that will ensure the weld quality online and prevent the occurrence of defects. In this paper an attempt is made to establish a correlation between the current and voltage signatures with the good weld and weld with porosity and burn through defect during the welding of carbon steel using gas metal arc welding (GMAW) process. Experimental setup has been established and experiments were conducted using a welding robot integrated with GMAW power source. The experimental setup includes online current and voltage sensors, data loggers, and signal processing hardware and software. Welding conditions are carefully designed to produce good weld and weld with defects such as burn through and porosity. Current and voltage signatures are captured using data acquisition system (DAS). Software has been developed to analyze the data captured by the DAS. Statistical methods are employed to study the transient data. The probability density distributions of the current and voltage signature demonstrates a good correspondence between the current and voltage signatures with the welding defect.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Martinussen, M.: Numerical modelling and model reduction of heat flow in robotic welding. Master Thesis, Norwegian University of Science and Technology (2007)

  2. Mirapeix, J.; García-Allende, P.B.; Cobo, A.; Conde, O.M.; López-Higuera, J.M.: Real-time arc-welding defect detection and classification with principal component analysis and artificial neural networks. Int. J. Non Destr. Test. Eval. 40, 315–323 (2007)

    Google Scholar 

  3. Zhiyong, L.; Bao, W.; Jingbin, D.: Detection of GTA welding quality and disturbance factors with spectral signal of arc light. J. Mater. Process. Technol. 209, 4867–4873 (2009)

    Article  Google Scholar 

  4. Pal, S.; Pal, S.K.; Samantaray, A.K.: Artificial neural network modeling of weld joint strength prediction of a pulsed metal inert gas welding process using arc signals. J. Mater. Process. Technol. 2(02), 464–474 (2008)

    Article  Google Scholar 

  5. Acherjee, B.; Mondal, S.; Tudu, B.; Misra, D.: Application of artificial neural network for predicting weld quality in laser transmission welding of thermoplastics. J. Appl. Soft Comput. 11, 2548–2555 (2011)

    Article  Google Scholar 

  6. Pal, K.; Bhattacharya, S.; Pal, S.K.: Investigation on arc sound and metal transfer modes for on-line monitoring in pulsed gas metal arc welding. J. Mater. Process. Technol. 210, 1397–1410 (2010)

    Article  Google Scholar 

  7. Cayo, E.H.; Alfaro, S.C.A.: A non-intrusive GMA welding process quality monitoring system using acoustic sensing. J. Sens. 9, 7150–7166 (2009)

    Article  Google Scholar 

  8. Saini, D.; Floyd, S.: An investigation of gas metal arc welding sound signature for online quality monitoring. Weld. Res. Suppl. 77(4), 172–179 (1998)

    Google Scholar 

  9. Chen, W.; Chin, B.A.: Monitoring joint penetration using infrared sensing techniques. Weld. J. 69, 181–185 (1992)

    Google Scholar 

  10. Nagarajan, S.; Banerjee, P.; Chen, W.; Chin, B.A.: Control of the welding process using Infrared Sensors. IEEE Trans. Robot. Autom. 8(1), 86–93 (1992)

    Article  Google Scholar 

  11. Wikle Iii, H.C.; Zee, R.H.; Chin, B.A.: A sensing system for weld process control. J. Mater. Process. Technol. 89–90, 254–259 (1999)

    Article  Google Scholar 

  12. Fan, H.; Ravala, N.K.; Wikle, H.C.; Chin, B.A.: Low-cost infrared sensing system for monitoring the welding. J. Mater. Process. Technol. 140, 668–675 (2003)

    Article  Google Scholar 

  13. Sforza, P.; Blasiis, D.: On-line optical monitoring system for arc welding. Int. J. Non Destr. Test. Eval. 35, 37–43 (2002)

    Google Scholar 

  14. Ling, S.F.; Wan, L.X.; Wong, Y.R.; Li, D.N.: Input electrical impedance as quality monitoring signature for characterizing resistance spot welding. Int. J. Non Destr. Test. Eval. 43(3), 200–205 (2010)

    Google Scholar 

  15. Ling, S.F.; Luan, J.; Li, X.; Ang, W.L.Y.: Input electrical impedance as signature for non-destructive evaluation of weld quality during ultrasonic welding of plastics. Int. J. Non Destr. Test. Eval. 39, 13–18 (2006)

    Google Scholar 

  16. Wu, C.S.; Gao, J.Q.; Hu, J.K.: Real-time sensing and monitoring in robotic gas metal arc welding. J. Phys. 18, 303–310 (2007)

    Google Scholar 

  17. Wang, Y.; Chen, Q.: On-line quality monitoring in plasma-arc welding. J. Mater. Process. Technol. 120, 270–274 (2001)

    Article  Google Scholar 

  18. Kang, M. J.; Rhee, S.: The Statistical Models for Estimating the Amount of Spatter in the Short Circuit Transfer Mode of GMAW. Welding Research Supplement. Sponsored by the American Welding Society and the Welding Research Council, pp. 1–8 (2001)

  19. McJunkin, T.R.; Kunerth, D.C.; Nichol, C.I.; Todorov, E.; Levesque, S.: Towards real time diagnostics of hybrid welding laser/GMAW. In: \(40^{{\rm th}}\) Annual Review of Progress in Quantitative Non destructive Evaluation (2014). doi:10.1063/1.4865029

  20. Nilsiam, Y.; Haselhuhn, A.; Wijnen, B.; Sanders, P.; Pearce, J.M.: Integrated voltage–current monitoring and control of gas metal arc weld magnetic ball-jointed open source 3-D printer. Machines 3(4), 339–351 (2015). doi:10.3390/machines3040339

    Article  Google Scholar 

  21. Pinar, A.; Wijnen, B.; Anzalone, G.C.; Havens, T.C.; Sanders, P.G.; Pearce, J.M.: Low-cost open-source voltage and current monitor for gas metal arc weld 3D printing. J. Sens. (2015). doi:10.1155/2015/876714

  22. Anzehaee, M.M.; Haeri, M.: Welding current and arc voltage control in a GMAW process using ARMarkov based MPC. Control Eng. Pract. 19, 1408–1422 (2011)

    Article  Google Scholar 

  23. Molleda, J.; Carús, J.L.; Usamentiaga, R.; García, D.F.; Granda, J.C.; Rendueles, J.L.: A fast and robust decision support system for in-line quality assessment of resistance seam welds in the steelmaking industry. J. Comput. Ind. 63, 222–230 (2012)

    Article  Google Scholar 

  24. SatheeshKumar, K.V.; Gejendhiran, S.; Prasath, M.: Comparative investigation of mechanical properties in GMAW/GTAW for various shielding gas compositions. Mater. Manuf. Process. 29(8), 996–1003 (2013)

    Google Scholar 

  25. Zhang, Z.; Chen, X.; Chen, H.; Zhong, J.; Chen, S.: Online welding quality monitoring based on feature extraction of arc voltage signal. Int. J. Adv. Manuf. Technol. 70(9–12), 1661–1671 (2014)

    Article  Google Scholar 

  26. Adolfsson, S.; Bahrami, A.; Bolmsjo, G.; Claesson, I.: On-line quality monitoring in short-circuit gas metal arc welding. Weld. Res. Suppl. 78, 59–73 (1999)

    Google Scholar 

  27. Rehfeldt, D.: Monitoring and analyzing systems for arc welding processes. JOM-1 (Join. Met.) 331–335 (1981)

  28. Rehfeldt, D.; Bollmann, A.: Using statistical signal analysis for analyzing and monitoring GMAW-processes. In: IIW Latin American Regional Welding Congress (IIW Congresso Regional Latino Americano de Soldagem), vol. 2, pp. 839–844. Rio de Janeiro, Brasil (1992)

  29. Rehfeldt, D.; Schmitz, T.H.: A system for process quality evaluation in GMAW. Weld. World 34, 227–334 (1994)

    Google Scholar 

  30. Rehfeldt, D.; Polte, T.; Franzbecker, H.; Lübbers, R.; Rostek, W.: Application potential of gas-shielded metal-arc welding with a strip electrode. Weld. Cut. 6, 299–303 (2002)

    Google Scholar 

  31. Rehfeldt, D.; Rehfeldt, M.D.: Computer-aided quality assurance (CAQ) of Al-MIG-welding with analysator hanover. In: Proceedings of International Forum on Automobile Welding (2003)

  32. Rehfeldt, D.; Rehfeldt, Markus D.: Statistical evaluation of GMAW process disturbances with signature analysis through Analysator Hannover. J. Chem. Pharm. Sci. 9, 274–279 (2015)

    Google Scholar 

  33. Wu, C.S.; Hu, Q.X.; Sun, J.S.; Polte, T.; Rehfeldt, D.: Intelligent monitoring and recognition of short-circuiting gas-metal arc welding process. Proc. Inst. Mech. Eng. 218(9), 1145–1151 (2004). doi:10.1243/0954405041897121

    Article  Google Scholar 

  34. Wu, C.S.; Polte, T.; Rehfeldt, D.: A fuzzy logic system for process monitoring and quality evaluation in GMAW. Weld. Res. Suppl. 2, 33–38 (2001)

    Google Scholar 

  35. Wu, C.S.; Polte, T.; Rehfeldt, D.: GMAW process monitoring and quality evaluation using neural network. Sci. Technol. Weld. Join. 5(5), 324–328 (2000)

    Article  Google Scholar 

  36. Kumar, V.; Albert, S.K.; Chandrasekhar, N.; Jayapandian, J.; Venkatesan, M.V.: Performance analysis of arc welding parameters using self organizing maps and probability density distributions. In: IEEE First International Conference on Control, Measurement and Instrumentation (CMI), pp. 196–200 (2016)

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Amrita Nagar P.O, Coimbatore, 641112, India

    A. Sumesh, K. Rameshkumar & K. Mohandas

  2. Welding Research Institute, Bharat Heavy Electricals Ltd., Tiruchirappalli, India

    A. Raja & A. Santhakumari

  3. Best Oil & Gas Solution LLC, Muscat, Sultanate of Oman

    R. Shyambabu

Authors
  1. A. Sumesh
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. K. Rameshkumar
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. Raja
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. K. Mohandas
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. A. Santhakumari
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. R. Shyambabu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. Sumesh.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sumesh, A., Rameshkumar, K., Raja, A. et al. Establishing Correlation Between Current and Voltage Signatures of the Arc and Weld Defects in GMAW Process. Arab J Sci Eng 42, 4649–4665 (2017). https://doi.org/10.1007/s13369-017-2609-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s13369-017-2609-9

Keywords

Search

Navigation