Abstract
Vibration measurement is a common method used to assess a structure’s condition. The basic premise for the detection of damage in a structure is based on vibration measurement, whereby changes of stiffness, vibration mode, and energy dissipation in the system can cause changes in the dynamic response. The vibration measurement is conducted by obtaining the fundamental period to judge the health condition of the monitored structure. This research used the high-speed camera (HSC) to capture the structure motion during the vibration of steel-plated structure. Laboratory experiments were performed on a thin steel plate (600 × 600 × 2.3 mm) and orthotropic steel deck. The HSC was used to measure the resonance frequency of the structure monitored.
Similar content being viewed by others
References
Carden EP, Fanning P (2004) Vibration based condition monitoring: a review. Struct Health Monit 3(4):355–377
Fan W, Qiao P (2011) Vibration-based damage identification methods: a review and comparative study. Struct Health Monit 10(1):83–111
Kudus SA, Suzuki Y, Matsumura M, Sugiura K (2018) Damage assessment based on sensitivity of modal parameter in plated structure. Malays Constr Res J 24(1):65–82
Salawu OS (1997) Detection of structural damage through changes in frequency: a review. Eng Struct 19(9):718–723
Farrar CR, Worden K (2007) An introduction to structural health monitoring. Philos Trans Royal Soc A 365(851):303–315
Worden K, Farrar CR, Manson G, Park G (2007) The fundamental axioms of structural health monitoring. Proc Royal Soc A 463(2082):1639–1664
Shull PJ (2002) Nondestructive evaluation: theory, techniques, and applications, vol 142. CRC, US
Basri SR, Bunnori NM, Kudus SA, Shahiron S, Jamil MNM, Noorsuhada MN (2013) Applications of acoustic emission technique associated with the fracture process zone in concrete beam: a review. Adv Mater Res 626:147–151 (Trans Tech Publications)
Bunnori N, Nor N, Jiun K, Kudus S (2016) Analysis of failure mechanisms in fatigue test of reinforced concrete beam utilizing acoustic emission. Int J Multiphysics 8(4)
Doebling SW, Farrar CR, Prime MB, Shevitz DW (1996) Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: a literature review (No. LA-13070-MS). Los Alamos National Lab., NM
Farrar CR, James GH III (1997) System identification from ambient vibration measurements on a bridge. J Sound Vib 205(1):1–18
Kaito K, Abe M, Fujino Y (2005) Development of non-contact scanning vibration measurement system for real-scale structures. Struct Infrastruct Eng 1(3):189–205
Nassif HH, Gindy M, Davis J (2005) Comparison of laser Doppler vibrometer with contact sensors for monitoring bridge deflection and vibration. NDT&E Int 38:213–218
Yuanpeng Z, Huaning Z, Wenling Z, Hefei L (2002) Application of the fourier transform in electronic speckle photography. Exp Mech 42(1):18–24
Valin JL, Gonçalves E, Palacios F, Pérez JR (2005) Methodology for analysis of displacement using digital holography. Opt Lasers Eng 43:99–111
Baqersad J, Niezrecki C, Avitabile P (2015) Full-field dynamic strain prediction on a wind turbine using displacements of optical targets measured by stereophotogrammetry. Mech Syst Signal Process 62:284–295
Helfrick MN, Niezrecki C, Avitabile P, Schmidt T (2011) 3D digital image correlation methods for full-field vibration measurement. Mech Syst Signal Process 25(3):917–927
Nonis C, Niezrecki C, Yu TY, Ahmed S, Su CF, Schmidt T (2013) Structural health monitoring of bridges using digital image correlation. Health Monit Struct Biol Syst 2013 8695:869507 (International Society for Optics and Photonics)
Sarrafi A, Mao Z, Niezrecki C, Poozesh P (2018) Vibration-based damage detection in wind turbine blades using phase-based motion estimation and motion magnification. J Sound Vib 421:300–318
Bruck HA, McNeill SR, Sutton MA, Peters WH (1989) Digital image correlation using newton-raphson method of partial differential correction. Exp Mech 29(3):261–267
Khoo SW, Karuppanan S, Tan CS (2016) A review of surface deformation and strain measurement using two-dimensional digital image correlation. Metrol Meas Syst 23(3):461–480
Yaofeng S, Pang JH (2007) Study of optimal subset size in digital image correlation of speckle pattern images. Opt Lasers Eng 45(9):967–974
Zhang Z (2000) A flexible new technique for camera calibration. IEEE Transactions on pattern analysis and machine intelligence, 22
Leissa AW (1969) Vibration of plates (NASA SP 160), Gov. Printing Office, Washington
Javh J, Slavič J, Boltežar M (2018) High frequency modal identification on noisy high-speed camera data. Mech Syst Signal Process 98:344–351
Acknowledgements
The authors would like to express their gratitude to NAC Image Technology for providing the high-speed camera.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Abdul Kudus, S., Sugiura, K., Suzuki, Y. et al. Dynamic response measurement of steel plate structure utilising video camera method. J Civil Struct Health Monit 9, 597–605 (2019). https://doi.org/10.1007/s13349-019-00351-w
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13349-019-00351-w