Abstract
In the present study, the dynamic and fatigue characteristics of two types of stress joints are investigated under ocean environmental condition. Connected with the riser and the platform, stress joint at the vessel hang-off position should be one of the main critical design challenges for a steel catenary riser (SCR) in deepwater. When the riser is under a high pressure and deepwater working condition, the stress state for the joint is more complex, and the fatigue damage is easy to occur at this position. Stress joint discussed in this paper includes two types: Tapered Stress Joint (TSJ) and Sleeved Stress Joint (SSJ), and multiaxial fatigue analysis results are given for comparison. Global dynamic analysis for an SCR is performed first, and then the local boundary conditions obtained from the previous analysis are applied to the stress joint FE model for the later dynamic and multiaxial fatigue analysis. Results indicate that the stress level is far lower than the yield limit of material and the damage induced by fatigue needs more attention. Besides, the damage character of the two types of stress joints differs: for TSJ, the place where the stress joint connects with the riser is easy to occur fatigue damage; for SSJ, the most probable position is at the place where the end of the inner sleeve pipe contacts with the riser body. Compared with SSJ, TSJ shows a higher stress level but better fatigue performance, and it will have a higher material cost. In consideration of various factors, designers should choose the most suitable type and also geometric parameters.
Similar content being viewed by others
References
Baugus, V., Baxter, C. and Trim, A., 1998. Use of titanium taper joints in risers — the Neptune field and future designs, Proc. 17th Int. Conf. Offshore Mech. Arctic Eng., OMAE1998, 49109.
Chang, S.-H. M., Stanton, P., Kuriakose, S. and Houston, T., 2010. Sleeved stress joint for steel catenary riser application, Proc. 29th Int. Conf. Ocean, Offshore Arctic Eng., OMAE2010-20168.
Cunliffe, N., McCarthy, T. J. and Trim, A., 2003. Optimisation of tapered stress joints for offshore catenary risers, The Structural Engineer, 81(20): 35–40.
DNV, 2005. Riser Fatigue, Offshore Standard, DNV-RP-F204.
Fu, J. J. and Yang, H. Z., 2010. Fatigue characteristic analysis of deepwater steel catenary risers at the touchdown point, China Ocean Eng., 24(2): 291–304.
Fatemi, A. and Shamsaei, N., 2011. Multiaxial fatigue: An overview and some approximation models for life estimation, Int. J. Fatigue, 33(8): 948–958.
Gordon, C. C. and Dareing, D. W., 2004. Configuring marine riser tapered stress joints used in top-supported applications, Journal of Energy Resources Technology, 126(3): 201–207.
Grealish, F., Kavanagh, K., Connaire, A. and Batty, P., 2007. Advanced nonlinear analysis methodologies for SCRs, Offshore Technology Conference, OTC 18922.
Gu, M., Chen, L. Z. and Xiang, H. F., 1998. A method in mixed frequency-time domain for fatigue life estimation of steel girders of cable-stayed bridges due to buffeting, Journal of Basic Science and Engineering, 6(4): 392–401.
Lima Torres, A. L. F., Mourelle, M. M. and Da Silva, R. M. C., 2001. Fatigue damage verification of steel catenary risers, Proc. 20th Int. Conf. Offshore Mech. Arctic Eng., OMAE2001, 1, 749–759.
Meniconi, L. C. M., Reid, S. R. and Soden, P. D., 2001. Preliminary design of composite riser flexible joints, Composites Part A: Applied Science and Manufacturing, 32(5): 597–605.
Nakhaee, A. and Zhang, J., 2010. Trenching effects on dynamic behavior of a steel catenary riser, Ocean Eng, 37(2–3): 277–288.
Sun, G. Q. and Shang, D. G., 2010. Prediction of fatigue lifetime under multiaxial cyclic loading using finite element analysis, Materials and Design, 31(1): 126–133.
Tong, D. J., Low, Y. M. and Sheehan, J. M., 2011. Nonlinear bend stiffener analysis using a simple formulation and finite element method, China Ocean Eng., 25(4): 577–590.
Yang, H. Z. and Li, H. J., 2010. Time domain fatigue life prediction for deepwater steel catenary riser, Journal of Vibration and Shock, 29(3): 22–25. (in Chinese)
Yang, H. Z. and Wang, A. J., 2012. Fatigue reliability based design optimization of bending stiffener, J. Ship Res., 56(2): 120–128.
Yang, H. Z. and Zheng, W. Q., 2011. Metamodel approach for reliability-based design optimization of a steel catenary riser, J. Mar. Sci. Technol., 16(2): 202–213.
You, B.-R. and Lee, S.-B., 1996. A critical review on multiaxial fatigue assessments of metals, Int. J. Fatigue, 18(4): 235–244.
Author information
Authors and Affiliations
Corresponding author
Additional information
This work was financially supported by the National Natural Science Foundation of China (Grant No. 51009093).
Rights and permissions
About this article
Cite this article
Zheng, Wq., Yang, Hz. & Li, Qq. Multiaxial fatigue analyses of stress joints for deepwater steel catenary risers. China Ocean Eng 26, 713–722 (2012). https://doi.org/10.1007/s13344-012-0053-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13344-012-0053-x