Abstract
The composite beams having high-strength steel (HSS) and high-strength concrete (HSC) can fully exploit the mechanical behavior of both materials. However, the published research on the structural behavior of composite beams using HSS and HSC is limited. In order to study the influences of shear connection degree and concrete strength on the flexural performance of composite beams using HSS and HSC, four composite beam specimens were constructed and loaded under four-point bending test in the present study. The test results showed that the failure mechanism of the fully connected composite beams was the bending failure of steel beam and crushing failure of concrete slab. The failure mode of the partially connected composite beams was the shear failure of stud connectors and bending failure of steel beam. The composite beams having 65% and 162% shear connection degree achieved the load bearing capacity of 18.8% and 25.3% higher than the composite beam having 38% shear connection degree. With the shear connection degree increased, the bending bearing capacity of the composite beam was enhanced. The concrete strength had no obvious impact on the flexural capacity of the composite beam having HSS and HSC. Moreover, the analytical models were put forward to predict the flexural capacity and bending stiffness of the composite beam using HSS and HSC.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Data Availability
All data generated or analysed during this study are included in this published article.
Code Availability
The custom code is available from the corresponding author on reasonable request.
References
An, L., & Cederwall, K. (1996). Push-out tests on studs in high strength and normal strength concrete. Journal of Constructional Steel Research, 36(1), 15–29. https://doi.org/10.1016/0143-974X(94)00036-H
Ban, H., & Bradford, M. A. (2013). Flexural behaviour of composite beams with high strength steel. Engineering Structures, 56, 1130–1141. https://doi.org/10.1016/j.engstruct.2013.06.040
Cao, J., Shao, X., Deng, L., & Gan, Y. (2017). Static and fatigue behavior of short-headed studs embedded in a thin ultrahigh-performance concrete layer. Journal of Bridge Engineering, 22(5), 04017005. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001031
Du, H., Hu, X., Meng, Y., Han, G., & Guo, K. (2020). Study on composite beams with prefabricated steel bar truss concrete slabs and demountable shear connectors. Engineering Structures, 210, 110419. https://doi.org/10.1016/j.engstruct.2020.110419
EN 1994-1-1. (2004). Eurocode 4: design of composite steel and concrete structures Part 1–1: General rules and rules for buildings. European Committee for Standardization.
Hegger, J., & Doinghaus, P. (2002). High performance steel and high performance concrete in composite structures. Composite Construction in Steel and Concrete IV Conference. https://doi.org/10.1061/40616(281)77
ISO 6892–1. (2016). Metallic materials-tensile testing-Part1: Method of test at room temperature. ISO.
Jun, S. C., Lee, C. H., Han, K. H., & Kim, J. W. (2018). Flexural behavior of high-strength steel hybrid composite beams. Journal of Constructional Steel Research, 149, 269–281. https://doi.org/10.1016/j.jcsr.2018.07.020
Kruszewski, D., Zaghi, A. E., & Wille, K. (2019). Finite element study of headed shear studs embedded in ultra-high performance concrete. Engineering Structures, 188, 538–552. https://doi.org/10.1016/j.engstruct.2019.03.035
Mans, P., Yakel, A. J., & Azizinamini, A. (2001). Full-scale testing of composite plate girders constructed using 485-Mpa high-performance steel. Journal of Bridge Engineering, 6(6), 598–604. https://doi.org/10.1061/(ASCE)1084-0702(2001)6:6(598)
Nie, J., Li, H., & Tang, L. (2009). Experimental study on HSS-concrete composite beams. Journal of Building Structures, 30(2), 64–69. (in Chinese).
Pocock, G. (2006). High strength steel use in Australia, Japan and the US. The Structural Engineer, 84(21), 27–30.
Tahir, M. M., Shek, P. N., & Tan, C. S. (2009). Push-off tests on pin-connected shear studs with composite steel–concrete beams. Construction & Building Materials, 23(9), 3024–3033. https://doi.org/10.1016/j.conbuildmat.2009.04.008
Uy, B., & Sloane, R. J. (1998). Behaviour of composite tee beams constructed with high strength steel. Journal of Constructional Steel Research, 46(1–3), 203–204. https://doi.org/10.1016/S0143-974X(98)00126-6
Wang, J., Guo, J., Jia, L., Chen, S., & Dong, Y. (2017). Push-out tests of demountable headed stud shear connectors in steel-UHPC composite structures. Composite Structures, 170, 69–79. https://doi.org/10.1016/j.compstruct.2017.03.004
Wang, J., Qi, J., Tong, T., Xu, Q., & Xiu, H. (2019). Static behavior of large stud shear connectors in steel-UHPC composite structures. Engineering Structures, 178, 534–542. https://doi.org/10.1016/j.engstruct.2018.07.058
Xu, X., Liu, Y., & He, J. (2014). Study on mechanical behavior of rubber-sleeved studs for steel and concrete composite structures. Construction & Building Materials, 53, 533–546. https://doi.org/10.1016/j.conbuildmat.2013.12.011
Xue, D., Liu, Y., Yu, Z., & He, J. (2012). Static behavior of multi-stud shear connectors for steel-concrete composite bridge. Journal of Constructional Steel Research, 74(8), 1–7. https://doi.org/10.1016/j.jcsr.2011.09.017
Xue, W., Ding, M., Wang, H., & Luo, Z. (2008). Static behavior and theoretical model of stud shear connectors. Journal of Bridge Engineering, 13(6), 623–634. https://doi.org/10.1061/(ASCE)1084-0702(2008)13:6(623)
Youn, S., Bae, D., & Kim, Y. J. (2011). Ultimate flexural strength of hybrid composite girders using high-performance steel of hsb600 at sagging bending. Composite Construction in Steel and Concrete VI. https://doi.org/10.1061/41142(396)56
Zhang, Y., Zhu, P., Wang, X., & Wu, J. (2020). Shear properties of the interface between ultra-high performance concrete and normal strength concrete. Construction & Building Materials, 248, 118455. https://doi.org/10.1016/j.conbuildmat.2020.118455
Acknowledgements
The research was supported by National Key Research and Development Program of China (No. 2017YFC0703405) and National Natural Science Foundation of China (Nos. 51678295, 51478220). The authors also thank Associate Mrs. Tong Zhang for revising and proofreading this manuscript.
Funding
The research was supported by National Key Research and Development Program of China (No. 2017YFC0703405) and National Natural Science Foundation of China (Nos. 51678295, 51478220).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
We declare that we have no conflicts of interest to this work. We declare that we do not have any commercial or associative interest that represents a conflict of interest in connection with the work submitted.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Du, H., Hu, X., Shi, D. et al. Flexural Performance of Composite Beams Using High-Strength Steel and High-Strength Concrete. Int J Steel Struct 22, 27–41 (2022). https://doi.org/10.1007/s13296-021-00558-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13296-021-00558-y