Skip to main content

Advertisement

SpringerLink
Log in

Propulsion system integration and thrust vectoring aspects for scaled jet UAVs

  • Original Paper
  • Published:
CEAS Aeronautical Journal Aims and scope Submit manuscript

Abstract

Scaled UAV configurations of planned aircraft is well suited for the trial of new aeronautical technologies in flight. These systems offer a significant potential for minimizing costs and complexity. For these reasons project Sagitta has been started with the support of the company Cassidian, namely, to build a scaled demonstrator of a full-scale configuration in order to prove the concept of those technologies. Among others, new technologies with respect to the propulsion system of the demonstrator shall be examined. The demonstrator has a flying wing configuration without vertical stabilizers and is powered by two jet engines. Due to the requirements for a low radar cross section for the full-scale configuration, the propulsion system shall have an adequate integration, leading to a curved propulsion duct, in order to integrate the engines as good as possible in the wing. In order to support lateral stability of the scaled configuration, thrust vectoring functionalities shall be implemented into the nozzle system. These aspects induce difficulties with respect to the integration and challenges with the scaling effects regarding the full-scale configuration. Other important issues of such propulsion integration are the total pressure losses in the inlet and nozzle duct, the thermal loads induced by the engine and the required power for the thrust vectoring concept. For the thrust vectoring system, fluidic concepts have been considered due to their potential for weight, complexity and maintenance effort reduction. Such systems have been mostly tested under laboratory conditions; therefore, a flying demonstrator would suit well for a flight trial of the technology. The presented paper will concentrate on the overall integration aspects of the propulsion system and the initial assessment of promising thrust vectoring solutions.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22

Similar content being viewed by others

References

  1. Banazadeh, A., Saghafi, F., Ghoreyshi, M., Pilidis, P.: Multi-directional co-flow fluidic thrust vectoring intended for small gas turbine. AIAA 2007-2940. CA, USA (2007)

  2. Baranski, J., Hoke, J.: Preliminary characterization of bio-fuels using a small scale gas turbine engine. AIAA 2011 0694. AIAA, Florida, USA (2011)

  3. Berens, D.: Ermittlung der Stromaufwärtswirkung des Triebwerks in stark gekrümmten Einläufen (2009)

  4. Berens, T., Bissinger, N.C.: Thrust vector behavior of highly integrated asymmetric nozzles for advances fighter aircraft. AIAA 1998, 0948. AIAA, Reno, NV, USA (1998)

  5. Deree, K.: Summary of fluidic thrust vectoring research conducted at NASA Langley research center. AIAA 2003-3800. AIAA, Hampton, VA, USA (2003)

  6. Deree, K., Berrier, B., Flamm, J., Johnson, S.: A computational study of a new dual throat fluidic thrust vectoring nozzle concept. AIAA 2005-3502 AIAA, USA, p. 5 (2005)

  7. Dores, D., Santos, M., Krothapalli, A., Lourenco, L., Collins Jr., E., Alvi, F., et al.: Characterization of a counterflow thrust vectoring scheme on a gas turbine engine exhaust jet. AIAA 2006-3516. AIAA, CA, USA (2006)

  8. Flamm, J.: Experimental study of a nozzle using fluidic counterflow for thrust vectoring. AIAA 1998-3255. NASA Langley Research Center, AIAA, Hampton, VA (1998)

  9. Flamm, J., Deere, K., Mason, M., Berrier, B., Johnson, K.: Design enhancements of the two-dimensional, dual throat fluidic thrust vectoring nozzle concept. 2006-3701. AIAA, San Francisco, USA (2006)

  10. Flamm, J.D., Deere, K.: Experimental study of an axisymmetric dual thrust fluidic thrust vectoring for supersonic aircraft application. AIAA 2007-5084. Hampton, VA, USA (2007)

  11. Kirk, A., Kumar, A., Gargoloff, J., Rediniotis, O., Cizmas, P.: Numerical and experimental investigation of a serpentine inlet duct. Reno, NV, USA

  12. Nicolai, L., Carichner, G.: Fundamentals of aircraft and airship design. Vol I—aircraft design. AIAA Education Series (2010)

  13. Raymer, D.: Aircraft design: A conceptual approach. AIAA (2006)

  14. Wilde, P., Gill, K., Michie, S., Crowther, W.: Integrated design of fluidic flight controls for a flapless aircraft. 2008-164. AIAA, Nevada, USA (2008)

Download references

Author information

Authors and Affiliations

  1. Institute of Aircraft Design, Boltzmannstr. 15, 85748, Garching by Munich, Germany

    L. Bougas & M. Hornung

Authors
  1. L. Bougas
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. Hornung
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to L. Bougas.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Bougas, L., Hornung, M. Propulsion system integration and thrust vectoring aspects for scaled jet UAVs. CEAS Aeronaut J 4, 327–343 (2013). https://doi.org/10.1007/s13272-013-0076-x

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s13272-013-0076-x

Keywords

Search

Navigation