Abstract
Injecting a room-temperature liquid metal into microchannels offers a simple, rapid, and low-cost method of fabricating microfluidic electrodes. In this work, these electrodes are used to develop a multichannel electroosmotic flow pump for high-flow-rate microfluidic bio analysis applications. In this pump, two identical square-wave shaped liquid metal electrodes were located at both ends of pumping channels on the same horizontal level, and were separated by polydimethylsiloxane gaps from the pumping channels. To test the pumping performance, fluorescent particles were diluted with deionized water and injected into the pumping channels to measure the flow velocity. The results show that the pump with five parallel pumping channels can drive water at a speed of 4.63–45.76 μm/s with applied voltage of 300–1000 V, when the pumping channels are 30 μm high, and 250 μm long with 30-μm polydimethylsiloxane gaps. It can reach its highest possible flow rate of 325 nl/min when the applied voltage reaches its limit 3900V (150 μm long pumping channels, 150 μm long nonpumping channels and 30 μm PDMS gap with 10 parallel pumping channels). This EOF pump should be potential in many high-flow-rate microfluidic applications.
Similar content being viewed by others
References
Laser, D. J. & Santiago, J. G. A review of micropumps. J. Micromech. Microeng. 14, R35 (2004).
Hwang, G., Haliyo, S. & Régnier, S. Infrared- photovoltaic properties of graphene revealed by electroosmotic spray direct patterning of electrodes. Micro Nano Lett. 5, 140–145 (2010).
Sinton, D., Erickson, D. & Li, D. Photo-injection based sample design and electroosmotic transport in microchannels. J. Micromech. Microeng. 12, 898–904 (2002).
Kamali, R., Radmehr, P. & Binesh, A. Molecular dynamics simulation of electro-osmotic flow in a nanonozzle. Micro Nano Lett. 7, 1049–1052 (2012).
Berrouche, Y., Avenas, Y., Schaeffer, C., Chang, H.-C. & Wang, P. Design of a porous electroosmotic pump used in power electronic cooling. IEEE Trans. Ind. Appl. 45, 2073–2079 (2009).
Chen, X., Zhang, L., Cai, H., Li, H., Sun, J. & Cui, D. Electrokinetic microchip-based sample loading for surface plasmon resonance detection. Micro Nano Lett. 8, 47–51 (2013).
Erickson, D., Sinton, D. & Li, D. Joule heating and heat transfer in poly (dimethylsiloxane) microfluidic systems. Lab Chip 3, 141–149 (2003).
Glawdel, T. & Ren, C. L. Electro-osmotic flow control for living cell analysis in microfluidic PDMS chips. Mech. Res. Commun. 36, 75–81 (2009).
Glawdel, T., Elbuken, C., Lee, L. E. & Ren, C. L. Microfluidic system with integrated electroosmotic pumps, concentration gradient generator and fish cell line (RTgill-W1)—towards water toxicity testing. Lab Chip 9, 3243–3250 (2009).
Gu, C., Jia, Z., Zhu, Z., He, C., Wang, W., Morgan, A., Lu, J.J. & Liu, S. Miniaturized Electroosmotic Pump Capable of Generating Pressures of More than 1200 Bar. Anal. Chem. 84, 9609–9614 (2012).
Wang, W., Gu, C., Lynch, K.B., Lu, J.J., Zhang, Z., Pu, Q. & Liu, S. High-Pressure Open-Channel On-Chip Electroosmotic Pump for Nanoflow High Performance Liquid Chromatography. Anal. Chem. 86, 1958–1964 (2014).
Shin, W., Zhu, E., Nagarale, R.K., Kim, C.H., Lee, J.M., Shin, S.J., & Heller, A. Nafion-Coating of the Electrodes Improves the Flow-Stability of the Ag/SiO2/Ag2O Electroosmotic Pump. Anal. Chem. 83, 5023–5025 (2011).
Nagarale, R. K., Heller, A. & Shin, W. A Stable Ag/Ceramic-Membrane/Ag2O Electroosmotic Pump Built with a Mesoporous Phosphosilicate-on-Silica Frit Membrane. J. Electrochem. Soc. 159, P14–P17 (2012).
Shin, W., Lee, J. M., Nagarale, R. K., Shin, S. J. & Heller, A. A Miniature, Nongassing Electroosmotic Pump Operating at 0.5 V. J. Am. Chem. Soc. 133, 2374–2377 (2011).
Lakhotiya, H., Mondal, K., Nagarale, R. K. & Sharma, A. Low voltage non-gassing electro-osmotic pump with zeta potential tuned aluminosilicate frits and organic dye electrodes. RSC Adv. 4, 28814–28821 (2014).
Kumar, R., Jahan, K., Nagarale, R. K. & Sharma, A. Nongassing Long-Lasting Electro-osmotic Pump with Polyaniline-wrapped Aminated Graphene Electrodes. ACS Appl. Mater. Interfaces 7, 593–601 (2015).
Cheng, S. & Wu, Z. Microfluidic electronics. Lab Chip 12, 2782–2791 (2012).
So, J.-H. & Dickey, M. D. Inherently aligned microfluidic electrodes composed of liquid metal. Lab Chip 11, 905–911 (2011).
Gao, M., Gui, L. & Liu, J. Study of liquid-metal based heating method for temperature gradient focusing purpose. J. Heat Transfer 135, 091402 (2013).
Fu, X., Mavrogiannis, N., Doria, S. & Gagnon, Z. Microfluidic pumping, routing and metering by contactless metal-based electro-osmosis. Lab Chip 15, 3600–3608 (2015).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (grant no. 31427801), the Beijing Natural Science Foundation (L172055) and the Beijing Municipal Science & Technology Commission research fund (Z1711000004 17004).
Author information
Authors and Affiliations
Corresponding author
Additional information
These authors contrilbuted equally.
Rights and permissions
About this article
Cite this article
Zheng, Y., Kang, K., Xie, F. et al. A Multichannel Electroosmotic Flow Pump Using Liquid Metal Electrodes. BioChip J 13, 217–225 (2019). https://doi.org/10.1007/s13206-019-3303-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13206-019-3303-7