Abstract
Within Alam El Bueib Formation (AEB), thin sandstone beds of approximately 15.24 m (~50 ft) total thickness, are considered to be the main conventional hydrocarbon-producing zone in the Western Desert. However, the shale intervals within the AEB can be an unconventional reservoir target. In this study, we focus on evaluating these shale units through geochemical analysis, to determine the total carbon, total sulfur, total organic carbon (TOC), and Rock–Eval pyrolysis. TOC is an essential property needed to determine the productive shale gas play. Total organic carbon combined with other geochemical data is important in evaluating the potential of shale gas reservoirs as it is related to the amount of kerogen, the produced hydrocarbon content. The TOC in the studied samples indicates poor to very good organic continent, while the hydrocarbon potentiality (S1 and S2) indicates poor source potential. The hydrogen index reflected kerogen type III/II. These data indicate that AEB Formation may be considered as a good source for generating hydrocarbons (mainly gas with minor amount of oil). The maturation evaluated by using “Tmax” indicates immature to marginally mature source rock, and production index ‘‘PI” represents oil and gas production in case of maturation.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Producing commercial rates of hydrocarbons in the shale reservoirs cannot be achieved without hydraulic stimulation, so it is described as unconventional reservoirs. Shale is not a rock type rather than a term widely used to describe rocks, i.e., mudstones that contain extremely fine grains typically <4 microns in diameter (Passey et al. 2010). Shale could also contain different amount of silt size particles which are up to 62.5 microns. Conventional sandstone rocks are composed of sand grains which can vary from 62.5 to 2000 microns in diameter (Passey et al. 2010). Shale contains variety of mineral grains, e.g., clay, quartz, feldspar, and heavy minerals like pyrite (Passey et al. 2010). This mixture of minerals is more heterogeneous in mudstones compared to sandstones. Evaluation of a shale gas formation is necessary to have a productive and commercial play. The work carried out by Kundert and Mullen (2009) reported the key properties necessary to have productive shale gas play which are illustrated in Table 1.
The Western Desert constitutes approximately two-thirds of the surface area of Egypt. It has been subjected to different tectonic regimes since the Paleozoic, which resulted in the formation of many sedimentary basins and sub-basins, ridges, troughs, and platforms. The study of the Cretaceous rock in Egypt in general and in the northern part of the Western Desert in particular is interesting due to its high hydrocarbon potentiality. This area consists of a number of sedimentary basins that received a thick succession of Mesozoic sediments. Many workers such as Abdine and Deibis (1972), Meshref et al. (1980), Meshref (1982), Abu El-Naga (1984), Moussa (1986), Barakat et al. (1987), El Shaarawy and Haggag (1990), Fawzy and Dahi (1992), EGPC (1992), and Schlumberger (1984, 1995) studied the most important geologic characteristics of these sedimentary basins which included stratigraphy, facies distribution, and tectonic framework.
The studied well Betty-1 (BYX-1) is located between latitude 29° 40′ 08′′N and longitude 27° 26′ 45′′E, Qattara Depression, northern part of the Western Desert of Egypt, represented in Fig. 1.
In the north Western Desert, Alam El Bueib (AEB) Formation is one of the main conventional hydrocarbon-producing zones. It is mainly composed of fine to coarse clastic sediments which conformably overly the carbonates of Masajed Formation (Upper Jurassic) and conformably underlay the Alamein Dolomite (Fig. 2). In the studied well, Alam El Bueib Formation composed mainly of sandstone, siltstone, calcareous shale, limestone with some streaks of coal (Fig. 3). These facies reflect shallow marine environment of deposition (Ramadan et al. 2012 and Temraz et al. 2016).
The sandstone within the Alam El Bueib Formation is the main conventional hydrocarbon-producing reservoir in the Western Desert and is studied by many authors such as El Nady (2013, 2015, and 2016), Ramadan et al. (2016), El Nady and Hakimi (2016), Eysa et al. (2016). They recognized that Alam El Bueib Formation is mature formation, derived from mixed organic sources, and has fair to good capability to generate gas. The present work aims to evaluate the shale within AEB through the interpretation of geochemical analysis data such as total carbon (TC), total sulfur (TS), total organic carbon (TOC), and Rock–Eval pyrolysis to highlight its potentiality to be a source rock or an unconventional reservoir.
Materials and methods
Nine shale core samples were collected from AEB Formation in Betty-1 (BYX-1) well. They were studied using LECO SC632 and Rock–Eval-6 pyrolysis techniques represented by different parameters.
Total organic carbon content (TOC) is used to assess the source rock quality. Approximately 200 mgs of homogenous pulverized rock sample was required. The samples were treated with hydrochloric acid (HCl) for about 12–24 h with intermittent stirring. When the dissolution of carbonates was observed to be complete (no effervescence with stirring or additional acid), the samples were washed several times using distilled water to remove any traces of HCl. The samples were dried to eliminate any moisture prior to analysis. Prepared samples were then combusted at ~1350 °C using LECO SC632 analyzer, and the amount of carbon dioxide (CO2) generated was measured using an infrared cell.
The pyrolysis analysis data obtained from Rock–Eval-6 analyzer, summarized as the “S1” and “S2”, are expressed in (mg/g of rock). “S3” peaks represent the quality of CO2 formed by pyrolysis of organic matter expressed in mg of CO2/g of rock. Tmax represented the temperature of maximum pyrolytic hydrocarbon generation; it is a useful parameter to evaluate the level of maturation for the studied samples. The “S2” and “S3” peaks values were normalized by the total organic carbon content (TOC wt%) in order to provide hydrogen index (HI = S2/TOC wt%) and oxygen index (OI = S3/TOC wt%). These parameters are used to indicate the kerogen type using the modified Van Krevelen type’s diagram (Espitalie et al. 1977). The analyses were performed at the Exploration Department of the Egyptian Petroleum Research Institute (EPRI), Cairo, Egypt.
Results and discussion
Organic richness
The organic carbon richness of the rock samples is expressed by the weight percent of total organic carbon content (TOC wt%). Peters and Casa (1994) reported that rocks containing <0.5% TOC are considered as poor source rocks. Between 0.5 and 1% TOC indicates fair source rock. TOC% value between 1 and 2% indicates good source rocks. TOC% values above 2% often indicate highly reducing environment with excellent source potential. In addition to the TOC content, the hydrocarbon potentiality has been also evaluated using S1 and S2. S1 from 0 to 0.5 and S2 from 1 to 2.5 are considered poor, S1 from 0.5 to 1 and S2 from 2.5 to 5 are fair, S1 from 1 to 2 and S2 from 5 to 10 are good, S1 from 2 to 4 and S2 from 10 to 20 are very good, and S1 > 4 and S2 > 20 are rated as excellent source rock. In the studied samples, the organic richness using TOC wt% ranges from 0.45 to 6.87 wt% (Table 2, Fig. 4a), indicating poor to excellent organic richness. Consequently, the hydrocarbon potential of the studied samples using S1 and S2 ranges from 0 to 0.36 and from 0 to 2.05 mg/g, respectively, which indicates poor source potential (Table 2, Fig. 4b).
Kerogen type
The pyrolysis data were used to evaluate the kerogen type of the studied samples utilizing the hydrogen index (HI) and oxygen index (OI) values. Waples (1985) used the hydrogen index values (HI) to differentiate between the types of organic matter. Kerogen with hydrogen indices above 600 mg/g usually consists of type I or type II kerogen and has excellent potential to generate oil. Kerogen with hydrogen indices between 300 and 600 mg/g contains a substantial amount of type II macerals and is considered to have good potential for generating oil and minor gas.
Kerogen with hydrogen indices between 150 and 300 mg/g contains type III kerogen more than type II and therefore is capable of generating mixed gas and oil but mainly gas. Hydrogen indices below about 150 mg/g indicate a potential source for generating gas (mainly type III kerogen). The hydrogen index (HI) of the studied samples ranges from 0 to 201 mg/g (Table 2, Fig. 5), which reflects type III/II kerogen, so it may be good source for generating mainly gas with minor amount of oil. This result is confirmed using Jackson et al. (1985) plot (Fig. 6).
Maturation
In the present study, the thermal maturity level of the source rocks has been determined by studying the geochemical parameters as Rock–Eval-6 temperature pyrolysis “Tmax” and production index “PI”. Peters (1986), Bordenove et al. (1993), and Espitalie et al. (1977) reported that the organic matter is in immature stage when ‘‘Tmax” has a value below 435 °C, ‘”Ro%” <0.5 and “PI” <0.2. Oil generation from source rocks began at “Tmax” 435–465 °C, vitrinite reflectance “Ro%” between 0.5 and 1.35%, and production index “PI” between 0.2 and 0.4. On the other hand, gas generation from source rocks began at “Tmax” 470 °C, “Ro%” >1.35%, and production index “PI” >0.4. In the studied samples, the Tmax ranges from 285 to 444 °C, indicating immature to marginally mature samples (Table 2, Fig. 7a). The PI ranges from 0 to 1, representing oil and gas production in case of maturation (Table 2, Fig. 7b).
Conclusion
Sandstone within the AEB Formation forms the main conventional hydrocarbon-producing zone in the Western Desert, while the shale intervals within the AEB Formation can be candidate unconventional reservoirs. The organic richness of the studied shale samples using TOC wt% ranges from 0.45 to 6.87 wt%, indicating poor to excellent organic richness. S1 and S2 range from 0 to 0.36 to 0 to 2.05 mg/g, respectively, indicating poor source potential. The hydrogen index (HI) of the studied samples ranges from 0 to 201 mg/g with kerogen type III/II. So it may be good source for generating gas with minor amount of oil. In the studied samples, the temperature pyrolysis “Tmax” ranges from 285 to 444 °C, indicating immature to marginally mature rocks. On the other hand, production index “PI” ranges from 0 to 1, representing oil and gas production in case of maturation.
References
Abdine AS, Deibis S (1972) Oil potentialities of Lower Cretaceous sediments in northern Western Desert: 8th Arab petroleum conference, Cairo, Egypt, 10–12 March 1972, p 24
Abu El Naga M (1984) Paleozoic and Mesozoic depocenters and hydrocarbon generating areas, north Western Desert: 7th Egyptian general petroleum corporation exploration seminar, Cairo, Egypt, 22–24 November 1984, p 8
Barakat MG, Darwish M, Abdel Hamid ML (1987) Hydrocarbon source rock evaluation of the Upper Cretaceous (Abu Roash Formation) east Abu Gharadig Area, north Western Desert, Egypt: Ain Shams University Earth Science Series 1, pp 120–150
Bordenove ML, Espitalie, J, Leplat P, Oudin JL, VandenBrouke M (1993). In: Bordenove (ed) Applied petroleum geochemistry, Paris Edition Tech., pp 217–278
Egyptian General Petroleum Corporation, EGPC (1992) Western Desert, oil and gas fields (a comprehensive overview): Cairo, Egypt, Egyptian General Petroleum Corporation, p 431
El Nady MM (2013) Geothermal history of hydrocarbon generation of wells in the North Western Desert, Egypt. J Energy Sources 35(5):401–412
El Nady MM (2015) Evaluation of the nature, origin and potentiality of the subsurface Middle Jurassic and Lower Cretaceous source rocks in Melleiha G-1x well, North Western Desert, Egypt. Egypt J Pet 24(3):317–323
El Nady MM (2016) Source rock potentiality of Middle Jurassic-Lower Cretaceous of wells, North Western Desert, Egypt. Energy Sources Part A Recovery Util Environ Effects 38(11):1635–1642
El Nady MM, Hakimi HM (2016) The petroleum generation modeling of prospective Jurassic-Cretacouse source rocks in Tut Oilfield, North Western Desert, Egypt: an integrated bulk pyrolysis and 1D- basin modeling. J Arab Geosci 9(6):1–14
El Shaarawy O, Haggag M (1990) Isosalinity study of the north Western Desert of Egypt: Egyptian General Petroleum Corporation 10th Petroleum Exploration and Petroleum Conference, Cairo, Egypt, 17–19 November 1990, pp 168–189
Espitalie J, Laporte L, Madec M, Marquis F, Leplat P, Paulet J, Boutefeu A (1977) Methode rapid de caracterisation des rocks meres, de leur potential petrolieretleur degree devolution. Rev Inst Fr Pet 32:23–42
Eysa EA, Ramadan FS, El Nady MM, Said NM (2016) Reservoir characterization using porosity—permeability relations and statistical analysis: a case study from North Western Desert, Egypt. J Arab Geosci 9(5):1–9
Fawzy A, Dahi M (1992) Regional geological evaluation of the Western Desert, Egypt. Geology of the Arab World Conference, Cairo University, Giza, Egypt, 28–30 January 1992, pp 111–149
Jackson KS, Hawkins PJ, Bennett AJR (1985) Regional facies and geochemical evaluation of southern Denison Trough. APEA J 20:143–158
Kundert D, Mullen M (2009) Proper evaluation of shale gas reservoirs leads to a more effective hydraulic fracture stimulation. SPE 123586:1–11
Meshref WM (1982) Regional structural setting of Northern Egypt. 6th Egyptian General Petroleum Corporation Exploration Seminar, Cairo, Egypt, January 1982, p 11
Meshref WM, Abdel Baki SH, Abdel Hady HM, Soliman SA (1980) Magnetic trend analysis in northern part of Arabian-Nubian Shield and its tectonic implications. Ann Geol Surv Egypt 10:939–953
Moussa S (1986) Evaluation of the sedimentary basins of the northern Western Desert, Egypt. 8th egyptian general petroleum corporation exploration seminar, Cairo, Egypt, 1–3 November 1986, p 14
Passey QR, Bohacs K, Esch WL, Klimentidis R, Sinha S (2010) From oil-prone source rock to gas-producing shale reservoir—geologic and petrophysical characterization of unconventional shale gas reservoirs. SPE131350, pp 1–29
Peters KE (1986) Guidelines for evaluating petroleum source rock using programmed pyrolysis. AAPG Bulletin 70:318–329
Peters KE, Cassa MR (1994) Applied source rock geochemistry. In: Magoon LB, Dows WG (eds) the petroleum system-from source to trap. AAPG, Tulsa, pp 93–117
Ramadan FS, Metwalli FI, El-Khadragy AA, Afify W (2012) The subsurface geology and source rocks characteristics of some Alam El Bueib reservoirs in Tut oil field, north Western Desert, Egypt. J Appl Sci Res 8(11):5388–5409
Ramadan FS, El Nady MM, Eysa EA, Mahdy SA (2016) Isopach, lithofacies changes, and source rocks chracteristics of Khatatba and Alam El Bueib formations of some wells in North East Western Desert, Egypt. J Pet Sci Technol 34(23):1920–1928
Schlumberger (1984) Well evaluation conference: Cairo, Egypt, p 243
Schlumberger (1995) Well evaluation conference: Cairo, Egypt, 8–10 April (1995), p 87
Temraz MG, Mandur MM, Coffey MB (2016) Reservoir sedimentology and depositional environment studies of Alam El Bueib Formation using microfacies and nannofossils in Betty-1 well, Shoushan Basin, northern Western Desert, Egypt. AAPG, 23(3):123–139
Waples DW (1985) Geochemistry in petroleum exploration. Reidel Publishing Company, Boston, p 232
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Temraz, M.G., Mousa, D.A. & Lotfy, M.A. Evaluation of the shale beds within Alam El Bueib Formation as an unconventional reservoir, Western Desert, Egypt. J Petrol Explor Prod Technol 8, 43–49 (2018). https://doi.org/10.1007/s13202-017-0353-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13202-017-0353-z