Skip to main content

Advertisement

SpringerLink
Log in

Influence of Variable Blank Holding Pressure on Impeller Sheets in Deep Drawing Process

  • Technical Paper
  • Published:
Transactions of the Indian Institute of Metals Aims and scope Submit manuscript

Abstract

In this research paper, a three dimensional elasto-plastic finite element (FE) model for mild steel material as blank has been developed to study the behavior of wrinkling on the impeller flange surface and parameters of deep drawing under different blank-holder pressure from 2.5 to 7.6 MPa. For modeling and simulation, commercially available FE software ANSYS 14.0 has been used. In industry, an experimental setup was built accordingly with a half cone angle of 36°. Experiments were carried out on a hydraulic press machine. The experimental results were compared with numerical results.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Rajabi A, Kadkhodayan M, Manoochehri M, and Farjadfar R, J Mater Process Technol 215 (2015) 159.

    Article  Google Scholar 

  2. Anaraki A P, Shahabizadeh M, and Babaee B, World Acad Sci, Eng Technol 61 (2012) 670.

    Google Scholar 

  3. Reddy R V, Reddy T A J, and Reddy G C M, Int J Eng Trends Technol 3 (2012) 53.

    Google Scholar 

  4. Gharib H, Wifi A S, Younan M, and Nassef A, J Achiev Mater Manuf Eng 18 (2006) 291.

    Google Scholar 

  5. Zhang S H, Nielsen K B, Danckert J, Kang D C, and Lang L H, J Mater Process Technol 102 (2000) 1.

    Article  Google Scholar 

  6. Dejmal I, Tirosh J, Shirizly A, and Rubinsky L, Int J Mech Sci 44 (2002) 1245.

    Article  Google Scholar 

  7. Duggal S K, Design of Steel Structures, Tata McGraw-Hill, New Delhi (2009) p 4.

    Google Scholar 

  8. Volk M, Nardin B, and Dolsak B, J Mech Eng 57 (2011) 697.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of MSME, Maulana Azad National Institute of Technology, Bhopal, India

    Ajay Kumar Choubey & C. Sasikumar

  2. Department of Mechanical Engineering, Maulana Azad National Institute of Technology, Bhopal, India

    Geeta Agnihotri

Authors
  1. Ajay Kumar Choubey
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Geeta Agnihotri
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. C. Sasikumar
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Ajay Kumar Choubey.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Choubey, A.K., Agnihotri, G. & Sasikumar, C. Influence of Variable Blank Holding Pressure on Impeller Sheets in Deep Drawing Process. Trans Indian Inst Met 68 (Suppl 1), 47–51 (2015). https://doi.org/10.1007/s12666-015-0603-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12666-015-0603-z

Keywords

Search

Navigation