Cost Effective Approach for Production of Chlorella pyrenoidosa: A RSM Based Study

Original Paper
  • 10 Downloads

Abstract

Microalgae are considered as a promising feedstock for biodiesel production due to their faster growth rate, higher biomass productivity and lipid content which ranges from 20 to 50% of its dry weight. In this work, optimization of bold basal media (BBM) for the production of Chlorella pyrenoidosa are studied with central composite design (CCD) using response surface methodology. The classical optimization is used for identifying the best pH for the growth of C. pyrenoidosa and found to be 8. The screening of significant factors for the growth was studied using Plackett–Burman design (PBD) with 7 factor experiment. The significant factors identified were MgSO4⋅7H2O, CaCl2⋅2H2O, KNO3, Na2EDTA from PBD of experiment. These significant factors were included in a CCD, resulting in 31 experiments, that were further performed. The chlorophyll a, chlorophyll b, chlorophyll a, b and turbidity were measured regularly during experiments. The optimum concentration of MgSO4⋅7H2O, CaCl2⋅2H2O, KNO3, and Na2EDTA were found to be 0.1, 0.0375, 0.375, and 0.0625 g/L, respectively. The turbidity, chlorophyll a, chlorophyll b and chlorophyll a, b obtained with optimum concentrations of BBM were 0.809, 5.7504, 1.6137 and 7.3642 mg/L respectively. The results showed a yield of more than 5 times higher with optimized BBM as compared to the actual media. Moreover, the effect of light and urea on C. pyrenoidosa growth were studied and it was found that turbidity, chlorophyll a, chlorophyll b and chlorophyll a, b were maximum when an artificial light of 3500 lx was used. The nitrogen starvation during the growth of C. pyrenoidoa showed a maximum lipid content of 36.03% dry weight on 16th day which is quite sufficient for the production of biodiesel. Hence, C. pyrenoidosa could be cultivated with the optimum BBM for biodiesel production.

Keywords

C. pyrenoidosa Bold basal media Plackett–Burman design Response surface methodology Turbidity 

Abbreviations

A665

Absorbance at 665 nm

A650

Absorbance at 650 nm

OD680

Optical density at 680 nm

Y1

Turbidity at 680 nm

Y2

Chlorophyll a content in mg/L

Y3

Chlorophyll b content in mg/L

Y4

Chlorophyll a, b content in mg/L

DF

Degrees of freedom

BBM

Bold basal media

ANOVA

Analysis of variance

RSM

Response surface methodology

CCD

Central composite design

PBD

Plackett–Burman design

Notes

Acknowledgements

The authors would like to thank Mechanical Engineering Department and School of Biotechnology, National Institute of Technology Calicut, and India for providing necessary lab facility for doing this work. The authors are thankful to Kerala State Council for Science, Technology and Environment (KSCSTE), Kerala, India for financially supporting (Order No. 1237/2015/KSCSTE) this investigation. A funding agency was involved in this work and facilities given by institute were acknowledged separately. This manuscript has not submitted elsewhere for the consideration of other journals and the manuscript has not been published partly/ fully. The results and conclusions given in the manuscript are original. No data, text, or theories by others are presented without mentioning the reference and as if they were the author’s own (“plagiarism”).

Compliance with Ethical Standards

Conflict of interest

The authors declare that they have no conflict of interest.

Ethical Approval

This manuscript was prepared according to the Committee on Publication Ethics (COPE) standard guidelines.

References

  1. 1.
    Abbaszaadeh, A., Ghobadian, B., Omidkhah, M.R., Najafi, G.: Current biodiesel production technologies: a comparative review. Energy Convers. Manag. 63, 138–148 (2012).  https://doi.org/10.1016/j.enconman.2012.02.027 CrossRefGoogle Scholar
  2. 2.
    Mubarak, M., Shaija, A., Suchithra, T.V.: A review on the extraction of lipid from microalgae for biodiesel production. Algal Res. 7, 117–123 (2015).  https://doi.org/10.1016/j.algal.2014.10.008 CrossRefGoogle Scholar
  3. 3.
    Rawat, I., Ranjith Kumar, R., Mutanda, T., Bux, F.: Biodiesel from microalgae: a critical evaluation from laboratory to large scale production. Appl. Energy. 103, 444–467 (2013).  https://doi.org/10.1016/j.apenergy.2012.10.004 CrossRefGoogle Scholar
  4. 4.
    Atabani, A.E., Silitonga, A.S., Ong, H.C., Mahlia, T.M.I., Masjuki, H.H., Badruddin, I.A., Fayaz, H.: Non-edible vegetable oils: a critical evaluation of oil extraction, fatty acid compositions, biodiesel production, characteristics, engine performance and emissions production. Renew. Sustain. Energy Rev. 18, 211–245 (2013).  https://doi.org/10.1016/j.rser.2012.10.013 CrossRefGoogle Scholar
  5. 5.
    Laurent Lardon, A.H., Sailve, B., Steyer, J.-P.: Olivier bernard life-cycle assessment of biodiesel production from microalgae. Environ. Sci. Technol. 43(17), 6475–6481 (2009)CrossRefGoogle Scholar
  6. 6.
    Chisti, Y.: Biodiesel from microalgae. Biotechnol. Adv. 25(3), 294–306 (2007).  https://doi.org/10.1016/j.biotechadv.2007.02.001 CrossRefGoogle Scholar
  7. 7.
    Mata, T.M., Martins, A.A., Caetano, N.S.: Microalgae for biodiesel production and other applications: a review. Renew. Sustain. Energy Rev. 14(1), 217–232 (2010).  https://doi.org/10.1016/j.rser.2009.07.020 CrossRefGoogle Scholar
  8. 8.
    Suali, E., Sarbatly, R.: Conversion of microalgae to biofuel. Renew. Sustain. Energy Rev. 16(6), 4316–4342 (2012).  https://doi.org/10.1016/j.rser.2012.03.047 CrossRefGoogle Scholar
  9. 9.
    Demirbas, A.: Use of algae as biofuel sources. Energy Convers. Manag. 51(12), 2738–2749 (2010).  https://doi.org/10.1016/j.enconman.2010.06.010 CrossRefGoogle Scholar
  10. 10.
    Daroch, M., Geng, S., Wang, G.: Recent advances in liquid biofuel production from algal feedstocks. Appl. Energy. 102, 1371–1381 (2013).  https://doi.org/10.1016/j.apenergy.2012.07.031 CrossRefGoogle Scholar
  11. 11.
    Lam, M.K., Lee, K.T.: Effect of carbon source towards the growth of Chlorella vulgaris for CO2 bio-mitigation and biodiesel production. Int. J. Greenhouse Gas Control. 14, 169–176 (2013).  https://doi.org/10.1016/j.ijggc.2013.01.016 CrossRefGoogle Scholar
  12. 12.
    Bilanovic, D., Andargatchew, A., Kroeger, T., Shelef, G.: Freshwater and marine microalgae sequestering of CO2 at different C and N concentrations—response surface methodology analysis. Energy Convers. Manag. 50(2), 262–267 (2009).  https://doi.org/10.1016/j.enconman.2008.09.024 CrossRefGoogle Scholar
  13. 13.
    Chen, T., Wang, Y.: Optimized astaxanthin production in Chlorella zofingiensis under dark condition by response surface methodology. Food Sci. Biotechnol. 22(5), 1–8 (2013).  https://doi.org/10.1007/s10068-013-0221-7 Google Scholar
  14. 14.
    Ravikumar, K., Pakshirajan, K., Swaminathan, T., Balu, K.: Optimization of batch process parameters using response surface methodology for dye removal by a novel adsorbent. Chem. Eng. J. 105(3), 131–138 (2005).  https://doi.org/10.1016/j.cej.2004.10.008 CrossRefGoogle Scholar
  15. 15.
    Gonen, F., Aksu, Z.: Use of response surface methodology (RSM) in the evaluation of growth and copper(II) bioaccumulation properties of Candida utilis in molasses medium. J. Hazard. Mater. 154(1–3), 731–738 (2008).  https://doi.org/10.1016/j.jhazmat.2007.10.086 CrossRefGoogle Scholar
  16. 16.
    Deepak, V., Kalishwaralal, K., Ramkumarpandian, S., Babu, S.V., Senthilkumar, S.R., Sangiliyandi, G.: Optimization of media composition for Nattokinase production by Bacillus subtilis using response surface methodology. Bioresour. Technol. 99(17), 8170–8174 (2008).  https://doi.org/10.1016/j.biortech.2008.03.018 CrossRefGoogle Scholar
  17. 17.
    Karthikeyan, K., Shanthi, N.K., Lakshmanaperumalsamy, K.P.: Response surface methodology for optimization of culture conditions for dye decolorization by a fungus, Aspergillus niger HM11 isolated from dye affected soil. Iranian J. Microbiol. 2(4), 213–222 (2010)Google Scholar
  18. 18.
    Ruangsomboon, S.: Effects of different media and nitrogen sources and levels on growth and lipid of green microalga Botryococcus braunii KMITL and its biodiesel properties based on fatty acid composition. Bioresour. Technol. (2015).  https://doi.org/10.1016/j.biortech.2015.01.091 Google Scholar
  19. 19.
    Lv, J.M., Cheng, L.H., Xu, X.H., Zhang, L., Chen, H.L.: Enhanced lipid production of Chlorella vulgaris by adjustment of cultivation conditions. Bioresour. Technol. 101(17), 6797–6804 (2010).  https://doi.org/10.1016/j.biortech.2010.03.120 CrossRefGoogle Scholar
  20. 20.
    Cheirsilp, B., Torpee, S.: Enhanced growth and lipid production of microalgae under mixotrophic culture condition: effect of light intensity, glucose concentration and fed-batch cultivation. Bioresour. Technol. 110, 510–516 (2012).  https://doi.org/10.1016/j.biortech.2012.01.125 CrossRefGoogle Scholar
  21. 21.
    Wang, H., Xiong, H., Hui, Z., Zeng, X.: Mixotrophic cultivation of Chlorella pyrenoidosa with diluted primary piggery wastewater to produce lipids. Bioresour. Technol. 104, 215–220 (2012).  https://doi.org/10.1016/j.biortech.2011.11.020 CrossRefGoogle Scholar
  22. 22.
    Griffiths, M.J., Harrison, S.T.L.: Lipid productivity as a key characteristic for choosing algal species for biodiesel production. J. Appl. Phycol. 21(5), 493–507 (2009).  https://doi.org/10.1007/s10811-008-9392-7 CrossRefGoogle Scholar
  23. 23.
    Ota, M., Kato, Y., Watanabe, M., Sato, Y., Smith, R.L. Jr., Rosello-Sastre, R., Posten, C., Inomata, H.: Effects of nitrate and oxygen on photoautotrophic lipid production from Chlorococcum littorale. Bioresour. Technol. 102(3), 3286–3292 (2011).  https://doi.org/10.1016/j.biortech.2010.10.024 CrossRefGoogle Scholar
  24. 24.
    Liu, Z.Y., Wang, G.C., Zhou, B.C.: Effect of iron on growth and lipid accumulation in Chlorella vulgaris. Bioresour. Technol. 99(11), 4717–4722 (2008).  https://doi.org/10.1016/j.biortech.2007.09.073 CrossRefGoogle Scholar
  25. 25.
    Feng, P., Deng, Z., Fan, L., Hu, Z.: Lipid accumulation and growth characteristics of Chlorella zofingiensis under different nitrate and phosphate concentrations. J. Biosci. Bioeng. 114(4), 405–410 (2012).  https://doi.org/10.1016/j.jbiosc.2012.05.007 CrossRefGoogle Scholar
  26. 26.
    Baky, A.E., El-Baroty, H.H., Bouaid, G.S., Martinez, A., Aracil, M.: Enhancement of lipid accumulation in Scenedesmus obliquus by optimizing CO2 and Fe3+ levels for biodiesel production. Bioresour. Technol. 119, 429–432 (2012).  https://doi.org/10.1016/j.biortech.2012.05.104 CrossRefGoogle Scholar
  27. 27.
    Mouedhen, G., Feki, M., Wery, M.D., Ayedi, H.F.: Behavior of aluminum electrodes in electrocoagulation process. J. Hazard. Mater. 150(1), 124–135 (2008).  https://doi.org/10.1016/j.jhazmat.2007.04.090 CrossRefGoogle Scholar
  28. 28.
    Fu, W., Gudmundsson, O., Feist, A.M., Herjolfsson, G., Brynjolfsson, S., Palsson, B.O.: Maximizing biomass productivity and cell density of Chlorella vulgaris by using light-emitting diode-based photobioreactor. J. Biotechnol. 161(3), 242–249 (2012).  https://doi.org/10.1016/j.jbiotec.2012.07.004 CrossRefGoogle Scholar
  29. 29.
    Becker, E.W.: Microalgae: Biotechnology and Microbiology. Cambridge University press, Cambridge, pp. 56–62 (1994)Google Scholar
  30. 30.
    Stowe, R.A., Mayer, R.P.: Efficient screening of process variables. Ind. Eng. Chem. Res. 56, 36–40 (1996)Google Scholar
  31. 31.
    Bligh, E.G., Dyer, W.J.: A rapid method for total lipid extraction and purification. Can. J. Biochem. Physiol. 37, 911–917 (1959)CrossRefGoogle Scholar
  32. 32.
    Daghrir, R., Igounet, L., Brar, S.-K., Drogui, P.: Novel electrochemical method for the recovery of lipids from microalgae for biodiesel production. J. Taiwan Inst. Chem. Eng. 45(1), 153–162 (2014).  https://doi.org/10.1016/j.jtice.2013.04.013 CrossRefGoogle Scholar
  33. 33.
    Song, X., Zhang, X., Kuang, C., Zhu, L., Guo, N.: Optimization of fermentation parameters for the biomass and DHA production of Schizochytrium limacinum OUC88 using response surface methodology. Process Biochem. 42(10), 1391–1397 (2007).  https://doi.org/10.1016/j.procbio.2007.07.014 CrossRefGoogle Scholar
  34. 34.
    Derringer, G., Suich, R.: Simultaneous optimization of several response variables. J. Qual. Technol. 12, 214–219 (1980)CrossRefGoogle Scholar
  35. 35.
    Nigam, S., Rai, M.P., Sharma, R.: Effect of nitrogen on growth and lipid content of Chlorella pyrenoidosa. Am. J. Biochem. Biotechnol. 7, 124–129 (2011)CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media B.V., part of Springer Nature 2018

Authors and Affiliations

  1. 1.Mechanical Engineering DepartmentNational Institute of Technology CalicutCalicutIndia
  2. 2.School of BiotechnologyNational Institute of Technology CalicutCalicutIndia

Personalised recommendations