Silicon

pp 1–8 | Cite as

Performance Monitoring of WEDM Using Online Acoustic Emission Technique

  • S. Suresh Kumar
  • M. Uthayakumar
  • S. Thirumalai Kumaran
  • P. Parameswaran
  • T. K. Haneef
  • C. K. Mukhopadhyay
  • B. P. C. Rao
Original Paper
  • 4 Downloads

Abstract

This study reveals the machining of Aluminium (Al) based hybrid Metal Matrix Composite (MMC) consists of Silicon Carbide (SiC) and Boron Carbide (B4C) as the reinforcements prepared through stir casting route. The composite is subjected to machining through Wire Electrical Discharge Machining (WEDM). The Acoustic Emission (AE) technique is incorporated to monitor the machining process through online. The WEDM cutting has been carried out at different feed rates (2.25, 3 and 3.75 mm/min) and AE signals generated during the machining are recorded using a 150 kHz resonant sensor along with the 40 dB pre-amplification and also band pass filter (100-400 kHz). The variation of AE counts, AE energy and amplitude with the respect to machining time for different feed rates are discussed in detail. The result shows that the generation of AE signals is not uniform and varies with time and feed rates. Sudden variation of AE counts, energy and amplitude during machining of the MMC shows crossing of cutting wire through different phases of work piece.

Keywords

Composite WEDM Acoustic emission 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

The authors express their thanks to DAE - BRNS, Mumbai, for providing the financial support to carry out this work vide project no. 2012/34/39/BRNS.

References

  1. 1.
    Rajmohan T, Palanikumar K (2011) Optimization of machining parameters for multi-performance characteristics in drilling hybrid metal matrix composites. J Compos Mater 46:869–878CrossRefGoogle Scholar
  2. 2.
    Zhenlong W, Xuesong G, Guanxin C, Yukui W (2014) Surface integrity associated with SiC/Al particulate composite by micro-wire electrical discharge machining. J Mater Manuf Process 29:532–539CrossRefGoogle Scholar
  3. 3.
    Kalaiselvan K, Muruganand N, Siva P (2011) Production and characterization of AA6061–B4C stir cast composite. Mater Des 2:4004–4009CrossRefGoogle Scholar
  4. 4.
    Vinoth Babu N, Moorthy TV (2014) Synthesis and characterization of Al7075/SiC composite by stir casting. Appl Mech Mater 592-594:760–764CrossRefGoogle Scholar
  5. 5.
    Show BK, Mondal DK, Biswas K, Maity J (2013) Development of a novel 6351 Al–(Al4SiC4 +SiC) hybrid composite with enhanced mechanical properties. Mater Sci Eng 579:136–149CrossRefGoogle Scholar
  6. 6.
    Mazahery A, Shabani MO (2012) Mechanical properties of squeeze-cast A356 composites reinforced with B4C particulates. J Mater Eng Perform 21:247–252CrossRefGoogle Scholar
  7. 7.
    Muller F, Monaghan J (2000) Non-conventional machining of particle reinforced metal matrix composite. Int J Mach Tools Manuf 40:1351–1366CrossRefGoogle Scholar
  8. 8.
    Manjaiah M, Narendranath S, Basavarajappa S (2016) Wire electro discharge machining performance of TiNiCu shape memory alloy. Silicon 8:467CrossRefGoogle Scholar
  9. 9.
    Sharma P, Chakradhar D, Narendranath S (2017) Analysis and optimization of WEDM performance characteristics of inconel 706 for aerospace application. Silicon,  https://doi.org/10.1007/s12633-017-9549-6
  10. 10.
    Lauro CH, Brandao LC, Baldo D, Reis RA, Davim JP (2014) Monitoring and processing signal applied in machining processes – a review. Measurement 58:73–86CrossRefGoogle Scholar
  11. 11.
    Chen X, Li B (2007) Acoustic emission method for tool condition monitoring based on wavelet analysis. Int J Adv Manuf Technol 33:968–976CrossRefGoogle Scholar
  12. 12.
    Annual Book of ASTM Standards, 03.03 (1990) Nondestructive testing. Section 3: metals test methods and analytical procedures, E610-89a. Standard Terminology Relating to Acoustic Emission, pp 269–271Google Scholar
  13. 13.
    Ravindra HV, Srinivasa YG, Krishnamurthy R (1993) Modeling for tool wear based on cutting forces in turing. Wear 169:25–32CrossRefGoogle Scholar
  14. 14.
    Guo YB, Ammula SC (2005) Real-time acoustic emission monitoring for surface damage in hard machining. Int J Mach Tools Manuf 45:1622–1627CrossRefGoogle Scholar
  15. 15.
    Haneef T, Lahiri BB, Bagavathiappan S, Mukhopadhyay CK, Philip J, Chandra Rao BP, Jayakumar T (2015) Study of the tensile behavior of AISI type 316 stainless steel using acoustic emission and infrared thermography techniques. J Mater Res Technol 4:241–253CrossRefGoogle Scholar
  16. 16.
    Klinka A, Holstena M, Schneidera S, Koshy P (2016) Acoustic emission signatures of electrical discharge machining. CIRP Ann Manuf Technol 65:229–232CrossRefGoogle Scholar
  17. 17.
    Shorowordi KM, Haseeb A, Celis JP (2006) Tribo-surface characteristic B4C and Al-SiC composites worn under different contact pressures. Wear 261:634–641CrossRefGoogle Scholar
  18. 18.
    Thirumalai Kumaran S, Uthayakumar M (2014) Investigation on the machining studies of AA6351-SiC-B4C hybrid metal matrix composites. Int J Mach Mach Mater 15:174–185Google Scholar
  19. 19.
    Suresh Kumar S, Uthayakumar M, Thirumalai Kumaran S, Parameswaran P, Mohandas E, Kempulraj G, Ramesh Babu BS, Natarajan SA (2015) parametric optimization of wire electrical discharge machining on aluminium based composites through grey relational analysis. J Manuf Process 20:33–39CrossRefGoogle Scholar
  20. 20.
    Suresh Kumar S, Uthayakumar M, Thirumalai Kumaran S, Parameswaran P, Mohandas E (2014) Electrical discharge machining of Al (6351)-5% SiC-10% B4C hybrid composite: a grey relational approach. Mod Simul Eng 2014:7Google Scholar
  21. 21.
    Haneef TK, Kumari K, Mukhopadhyay CK, Venkatachalapathy PRB, Jayakumar T (2013) Influence of fly ash and curing on cracking behavior of concrete by acoustic emission technique. Construct Build Mater 44:342–350CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media B.V., part of Springer Nature 2018

Authors and Affiliations

  • S. Suresh Kumar
    • 1
  • M. Uthayakumar
    • 1
  • S. Thirumalai Kumaran
    • 1
  • P. Parameswaran
    • 2
  • T. K. Haneef
    • 3
  • C. K. Mukhopadhyay
    • 3
  • B. P. C. Rao
    • 3
  1. 1.Faculty of Mechanical EngineeringKalasalingam UniversityKrishnankoilIndia
  2. 2.Physical Metallurgy GroupIndira Gandhi Center for Atomic ResearchKalpakkamIndia
  3. 3.Metallurgy and Materials GroupIndira Gandhi Center for Atomic ResearchKalpakkamIndia

Personalised recommendations