Abstract
The effect of Al on the morphology of MnS in medium-carbon non-quenched and tempered steel was investigated at three different cooling rates of 0.24, 0.43, and 200°C·s-1. The formation mechanisms of three types of MnS were elucidated based on phase diagram information combined with crystal growth models. The morphology of MnS is governed by the precipitation mode and the growth conditions. A monotectic reaction and subsequent fast solidification lead to globular Type I MnS. Type II MnS inclusions with different morphological characteristics form as a result of a eutectic reaction followed by the growth in the Fe matrix. Type III MnS presents a divorced eutectic morphology. At the cooling rate of 0.24°C·s−1, the precipitation of dispersed Type III MnS is significantly enhanced by the addition of 0.044wt% acid-soluble Al (Als), while Type II MnS clusters prefer to form in steels with either 0.034wt% or 0.052wt% Als. At the relatively higher cooling rates of 200°C·s−1 and 0.43°C·s−1, the formation of Type I and Type II MnS inclusions is promoted, and the influence of Al is negligible. The results of this work are expected to be employed in practice to improve the mechanical properties of non-quenched and tempered steels.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Y.J. Xia, F.M. Wang, J.L. Wang, and G.Z. Li, Simulation of the continuous casting process in a mold of free-cutting steel 38MnVS based on a MiLE method, Int. J. Miner. Metall. Mater., 18(2011), No. 5, p. 562.
X.Y. Mao, X.M. Zhao, Z.Z. Wang, L. Cai, and Y.Q. Bai, Effect of ageing on mechanical and impact properties of non-quenched and tempered steel wire strengthened by cold forming, Philos. Mag. Lett., 94(2014), No. 3, p. 135.
Z.B. Yang, F.M. Wang, S. Wang, and B. Song, Intragranular ferrite formation mechanism and mechanical properties of non-quenched-and-tempered medium carbon steels, Steel Res. Int., 79(2008), No. 5, p. 390.
Y.N. Wang, Y.P. Bao, M. Wang, and L.C. Zhang, Precipitation behavior of BN type inclusions in 42CrMo steel, Int. J. Miner. Metall. Mater., 20(2013), No.1, p. 28.
G.L. Sun, B. Song, L.Z. Yang, S.F. Tao, and Y. Yang, Effect of manganese sulfide on the precipitation behavior of tin in steel, Int. J. Miner. Metall. Mater., 21(2014), No. 7, p. 654.
S.B. Hosseini, C. Temmel, B. Karlsson, and N.G. Ingesten, An in-situ scanning electron microscopy study of the bonding between MnS inclusions and the matrix during tensile deformation of hot-rolled steels, Metall. Mater. Trans. A, 38(2007), No. 5, p. 982.
X.J. Shao, X.H. Wang, M. Jiang, F.X. Huang, and Y.Q. Ji, In situ observation of MnS inclusion behavior in resulfurized free-cutting steel during heating, Acta Metall. Sin., 47(2011), No. 9, p. 1210.
C.E. Sims, The nonmetallic constituents of steel, Trans. AIME, 215(1959), p. 367.
H. Fredriksson and M. Hillert, On the formation of manganese sulphide inclusions in steel, Scand. J. Metall., 2(1973), p. 125.
K. Oikawa, S.I. Sumi, and K. Ishida, Morphology control of MnS inclusions in steel during solidification by the addition of Ti and Al, Z. Metallkd., 90(1999), No. 1, p. 13.
P.P. Mohla and J. Beech, Effect of cooling rate on the morphology of sulphide inclusions, J Iron Steel Inst., 207(1969), p. 177.
Y.N. Wang, Y.P. Bao, M. Wang, L.C. Zhang, and Y.N. Chen, Basic research on precipitation and control of BN inclusions in steel, Metall. Mater. Trans. B, 44(2013), No. 5, p. 1144.
R. Dekkers, B. Blanpain, and P. Wollants, Crystal growth in liquid steel during secondary metallurgy, Metall. Mater. Trans. B, 34(2003), No. 2, p. 161.
M.A. Van Ende,_M.X. Guo, B. Blanpain, and P. Wollants, Laboratory study on the formation of Al2O3 inclusions at the on-set of deoxidation and during reoxidation, Front. Mater. Sci., 5(2011), No. 1, p. 69.
C. Temmel, N. Ingesten, and B. Karlsson, Fatigue anisotropy in cross-rolled, hardened medium carbon steel resulting from MnS inclusions, Metall. Mater. Trans. A, 37(2006), No. 10, p. 2995.
H.T. Liu and W.Q. Chen, Effect of total oxygen content on the machinability of low carbon resulfurized free cutting steel, Steel Res. Int., 83(2012), No. 12, p. 1172.
S.C. Chen, R. Zhu, L.Q. Xue, T.C. Lin, J.S. Li, and Y. Lin, Effects of elemental Sn on the properties and inclusions of the free-cutting steel, Int. J. Miner. Metall. Mater., 22(2015), No. 2, p. 141.
K.I. Yamamoto, H. Yamamura, and Y. Suwa, Behavior of non-metallic inclusions in steel during hot deformation and the effects of deformed inclusions on local ductility, ISIJ Int., 51(2011), No. 12, p. 1987.
J. Janis, K. Nakajima, A. Karasev, S. Jonsson, R. Inoue, and P.G. Jönsson, Effects of primary oxide and oxide-nitride particles on the solidification structure in a Fe-20 mass%Cr alloy deoxidised with Ti and M (M = Zr or Ce), ISIJ Int., 53(2013), No. 2, p. 221.
Y.J. Xia, F.M. Wang, J.L. Wang, and J. Zhao, Effect of oxygen content on the formation behavior of sulfides in free-cutting steel, J. Univ. Sci. Technol. Beijing, 32(2010), No. 10, p. 1271.
I. Sunagawa, Morphology of Crystals, Part B: Fine Particles, Minerals and Snow, Terra Scientific Publishing Company, Tokyo, 1987, p. 509.
R. Dekkers, B. Blanpain, P. Wollants, F. Haers, C. Vercruyssen, and B. Gommers, Non-metallic inclusions in aluminium killed steels, Ironmaking Steelmaking, 29(2002), No. 6, p. 437.
J.H. Shim, Y.J. Oh, J.Y. Suh, Y.W. Cho, J.D. Shim, J.S. Byun, and D.N. Lee, Ferrite nucleation potency of non-metallic inclusions in medium carbon steels, Acta Mater., 49(2001), No. 12, p. 2115.
D.S. Sarma, A.V. Karasev, and P.G. Jönsson, On the role of non-metallic inclusions in the nucleation of acicular ferrite in steels, ISIJ Int., 49(2009), No. 7, p. 1063.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.
The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
To view a copy of this licence, visit https://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Li, Ml., Wang, Fm., Li, Cr. et al. Effects of cooling rate and Al on MnS formation in medium-carbon non-quenched and tempered steels. Int J Miner Metall Mater 22, 589–597 (2015). https://doi.org/10.1007/s12613-015-1111-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-015-1111-1