Abstract
The purpose of this research was to investigate the suitability of the Fused Filament Fabrication (FFF) process for low pressure/vacuum environment. This included investigating the ability of an FFF printer to function in a vacuum and evaluation of the dimensional accuracy and mechanical properties of the manufactured components. For this purpose, a commercially available FFF printer using polycarbonate as raw material was placed in a vacuum environment of 10 mbar. Test components were then fabricated in vacuum with a control group fabricated in a normal atmosphere (1 bar). Test components were evaluated for dimensional and mass accuracy, quality and presence of defects. Flexural, tensile and compressive testing was carried out according to ASTM D790, D638 and D695 respectively. Dimensional analysis of components showed equivalent small deviation for both environments. Components fabricated in the vacuum environment had 5.4% higher tensile yield strength and 59% higher extension at break compared to components printed in a normal atmosphere indicating an increased strength and ductility. Components tested in compression had approximately 11.2% higher compressive strength when printed in a vacuum environment. No differences were observed during the flexural test. In space, due to the vacuum environment, polymers and organic material are susceptible to release molecules via an outgassing process. Assessment of the molecular organic contamination generate during the printing process in vacuum is low and seems to mostly originated from the components of the printer. The results provided demonstrated the possibility to use the FFF process in a vacuum environment to fabricate dimensionally accurate, high-quality polycarbonate components with a variety of geometries without loss of mechanical performance. This work provides a proof of concept that FFF can be used to develop out-of-earth manufacturing technologies (in orbit/in space/on planet) allowing part production for new maintenance and repair strategy or to potentially manufacture entire structure more efficiently overpassing launch constrain by using only raw material brought from earth.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Moraguez, M., De Weck, O.: Benefits of in-space manufacturing technology development for human spaceflight. In: 2020 IEEE Aerospace Conference, pp. 1–11. (2020)
Prater, T., Bean, Q., Werkheiser, N., Grguel, R., Beshears, R., Rolin, T., Huff, T., Ryan, R., Ledbetter, F., Ordonez, E.: Analysis of specimens from phase I of the 3D printing in Zero G technology demonstration mission. Rapid Prototyp. J. 23, 1212–1225 (2017). https://doi.org/10.1108/RPJ-09-2016-0142
Werkheiser, M.J., Dunn, J., Snyder, M.P., Edmunson, J., Cooper, K., Johnston, M.M.: 3D printing in Zero-G ISS technology demonstration. In: AIAA SPACE 2014 Conference and Exposition, p. 4470. (2014)
Prater, T., Werkheiser, N., Ledbetter, F., Timucin, D., Wheeler, K., Snyder, M.: 3D Printing in Zero G Technology Demonstration Mission: complete experimental results and summary of related material modeling efforts. Int. J. Adv. Manuf. Technol. 101, 391–417 (2019). https://doi.org/10.1007/s00170-018-2827-7
Musso, G., Lentini, G., Enrietti, L., Volpe, C., Ambrosio, E.P., Lorusso, M., Mascetti, G., Valentini, G.: Portable on orbit printer 3D: 1st European additive manufacturing machine on international space station. In: Advances in Physical Ergonomics and Human Factors, pp. 643–655. Springer, Cham (2016)
Prater, T., Werkheiser, N., Ledbetter, F., Morgan, K.: In-space manufacturing at NASA marshall space flight center: a portfolio of fabrication and recycling technology development for the international space station. In: 2018 AIAA SPACE and Astronautics Forum and Exposition, p. 5364. (2018)
Quinn, M., Guo, J., Lafont, U., Versteegh, J.: Fused filament fabrication of polycarbonate components in a simulated on-orbit environment. In: Proceedings of the 69th International Astronautical Congress (IAC 2018). International Astronautical Federation, IAF (2018)
European Cooperation for Space Standardization: ECSS-Q-ST-70–05C Rev.1: Detection of organic contamination surfaces by IR spectroscopy. (2019)
Kohad, A., Dalu, R.: Optimization of process parameters in fused deposition modeling: a review. Int. J. Innov. Res. Sci. Eng. Technol. 6, 505-511 (2017)
Tiwari, K., Kumar, S.: Analysis of the factors affecting the dimensional accuracy of 3D printed products. Mater. Today: Proc. 5, 18674–18680 (2018)
European Cooperation For Space Standardization: ECSS-Q-ST-70-02C: Thermal vacuum outgassing test for the screening of space materials. (2008)
Daurskikh, A., Sgambati, A., Graça, D., Berg, M., Baptista, A., Angelo, M., Lafont, U.: Influence of spatial orientation on properties of 3D printed PEEK parts and their design adaptation. In: Proceedings of the 69th International Astronautical Congress (IAC 2018). International Astronautical Federation, IAF (2018)
Acknowledgements
The authors would like to acknowledge S. Uladag, G. Mulder and B. Grashof from TU Delft for providing support for mechanical testing. Ultimaker B.V. is also acknowledged for providing the printer, polycarbonate material and replacement components. The authors would like to thank Dr. Christopher Semprimoschnig to enable this collaboration with ESA.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Quinn, M., Lafont, U., Versteegh, J. et al. Effect of low vacuum environment on the fused filament fabrication process. CEAS Space J 13, 369–376 (2021). https://doi.org/10.1007/s12567-021-00363-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12567-021-00363-7