Abstract
Achievable benefits of the transpiration cooled ceramic thrust chamber are the reduction of weight and manufacturing cost, as well as an increased reliability and higher lifetime due to thermal cycle stability. The transpiration cooling principle however reduces the engine performance. In order to evaluate the performance losses a \(c^*\)-analysis is performed. Due to the transpiration cooling the characteristic velocity decreases with increasing coolant ratio. The goal of the chamber development is therefore to minimize the required coolant mass flow. The paper discusses the test specimen set up for the ceramic thrust chamber tests. Chamber operating parameters are listed. The paper discusses the impact of transpiration cooling on the calculated \(c^*\) efficiency. The evaluation is based on test results with the ceramic combustion chamber conducted in four separate test campaigns between 2008 and 2012.
Similar content being viewed by others
Abbreviations
- \(a\) :
-
Sonic velocity, m/s
- \(A\) :
-
Cross section area, \(\rm{ m}^2\)
- \(c^*\) :
-
Characteristic velocity, m/s
- \(C_{\rm F}\) :
-
Thrust coefficient
- \(d\) :
-
Diameter, m
- \(F\) :
-
Thrust force, N
- \(g_0\) :
-
Gravitational acceleration, \(\rm{ m}/\rm{ s}^2\)
- \(I\) :
-
Specific impulse, m/s
- \( k_{\rm T}\) :
-
Transpiration cooling coefficient
- \(l\) :
-
(Chamber) length, m
- \(l^*\) :
-
Characteristic chamber length, m
- \(\dot{m}\) :
-
Mass flow, kg/s
- \(p\) :
-
Pressure, Pa
- \(R\) :
-
Mass mixture ratio (oxidizer to fuel)
- \(V\) :
-
Volume, \(\rm{ m}^3\)
- \(\eta \) :
-
Efficiency
- \(\rho \) :
-
Density, kg/\(\rm{ m}^3\)
- \(\tau \) :
-
Coolant ratio
- \(0\) :
-
Initial, injection
- \({\rm c}\) :
-
Chamber
- \({\rm e}\) :
-
Exit (nozzle)
- \({\rm fu}\) :
-
Fuel
- \({\rm id}\) :
-
Ideal
- \({\rm k}\) :
-
Coolant
- \({\rm ox}\) :
-
Oxidizer
- \({\rm t}\) :
-
Throat (nozzle)
- \({\rm vac}\) :
-
Vacuum
References
Gordon, S., McBride, B.J.: Computer Program for Calculation of Complex Chemical Equilibrium Compositions and Applications, Vol. II: Users Manual and Program Description. NASA Lewis Research Center. NASA RP-1311 (1996)
Görgen, J., Knab, O., Haeseler, D., Wennerberg, D.: Impact of intentional and unintentional combustion chamber porosity on rocket engine characteristics. In: Fourth international symposium on liquid space propulsion (2000)
Haeseler, D., Mäding, C., Rubinskiy, V., Gorokhov, V., Khrisanfov, S.: Experimental investigation of transpiration cooled hydrogen-oxygen subscale chambers. In: 34th joint propulsion conference. AIAA 98–3364 (1998)
Hald, H., Herbertz, A., Kuhn, M., Ortelt, M.: Technological aspects of transpiration cooled composite structures for thrust chamber applications. In: 16th AIAA/DLR/DGLR international space planes and hypersonic systems and technologies conference. Bremen (2009)
Herbertz, A.: Systemanalytische untersuchung einer brennkammer in faserkeramischer bauweise von raketenantrieben. Ph.D. thesis, RWTH Aachen (2008)
Herbertz, A., Ortelt, M., Müller, I., Hald, H.: Potential applications of the ceramic thrust chamber technology for future transpiration cooled rocket engines. Trans Jpn Soc Aeronaut Space Sci Aerospace Technol Jpn. 10(ists28) (2012). https://www.jstage.jst.go.jp/result?favorite=&type=100%2C200&language=en&item1=2&word1=Potential+applications+of+the+ceramic+thrust+chamber+technology+for+future+transpiration+cooled+rocket+engines.+&cond1=2&item2=8&word2=herbertz&cond2=2&translate=0&category=070000%2C070100%2C072100%2C073100%2C074100%2C075100&searchlocale=en&fromid=AF13S010
Herbertz, A., Ortelt, M., Müller, I., Hald, H.: Transpiration-cooled ceramic thrust chamber applicability for high-thrust rocket engines. In: 48th joint propulsion conference, Atlanta, Georgia. AIAA-2012-3990 (2012)
Herbertz, A., Selzer, M.: Analysis of coolant mass flow requirements for transpiration cooled ceramic thrust chambers. In: 29th international symposium on space technology and science. Nagoja (2013)
Humble, R., Henry, G., Larson, W.: Space Propulsion Analysis and Design. McGraw-Hill, New York (1995)
Ortelt, M., Hald, H., Elsäßer, H., Herbertz, A., Müller, I.: Structural investigations on cryogenically operated and transpiration cooled fiber reinforced rocket thrust chambers. In: 48th joint propulsion conference, Atlanta, Georgia. AIAA-2012-4010 (2012)
Sutton, G.P., Biblarz, O.: Rocket Propulsion Elements, 7th edn. Wiley, New York (2001)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Herbertz, A., Ortelt, M., Müller, I. et al. \(c^*\)-Efficiency evaluation of transpiration cooled ceramic combustion chambers. CEAS Space J 6, 99–105 (2014). https://doi.org/10.1007/s12567-014-0062-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12567-014-0062-0