Abstract
The direct measurement of grinding temperature is always difficult due to coolant cover and very size of work and wheel interaction zone. At the same time, high heat generation in grinding often leads to grinding burns thereby affecting surface integrity; in this context, theoretical evaluation of temperature could facilitate early detection of the grinding burns. This paper therefore presents an analytical model to evaluate grinding temperature and correlates it with the occurrence of grinding burns in terms of BNA. In general, the analytical approach involves evaluating real contact length, grinding forces and finally grinding zone temperature for the plunge cylindrical grinding. The maximum rise in grinding temperature at the surface was calculated, for the wet grinding process by considering the total heat flux entering into the grinding system. Model validation experiments have been performed to measure BNA and identify parametric conditions that produce grinding burns. The model estimate of grinding zone temperature of 631 °C is in good agreement (92%) with other research works. Further, when the calculated grinding temperature reaches beyond 631 °C, the grinding burns are observed on the work surface with a BNA value of the order of 100 mp for the micro alloyed steel. The minimum thermal damage in terms of BNA is observed at higher levels of wheel speed and spark-out time and lower levels of depth of cut.
Similar content being viewed by others
Abbreviations
- D :
-
Spherical grain diameter
- C d :
-
Number of active grains per unit area
- C w :
-
Specific heat density of work material
- E 1 :
-
Modulus of elasticity of work-piece
- E 2 :
-
Modulus of elasticity of grinding wheel
- E*:
-
Elastic properties of work-wheel
- F :
-
Friction coefficient between chip, grain, and the work-piece
- F n :
-
Normal grinding force
- \(F_{n}^{\prime }\) :
-
Specific normal grinding force
- \(F_{nchip}^{\prime }\) :
-
Specific normal cutting force
- \(F_{nslide}^{\prime }\) :
-
Specific normal sliding force
- \(F_{nplough}^{\prime }\) :
-
Specific normal ploughing force
- HB:
-
Brinell hardness number of the work-piece
- L :
-
Paclet number
- M :
-
Size of an abrasive grain mesh size
- R a :
-
Surface roughness
- R L :
-
Contact length ratio
- R r :
-
Roughness factor
- R ws :
-
Work-wheel fraction
- T ch :
-
Chip temperature
- V s :
-
Wheel velocity
- V w :
-
Work velocity
- a e :
-
Depth of cut
- b :
-
Impression diameter
- b w :
-
Width of grinding
- d g :
-
Equivalent diameter of abrasive grain
- d e :
-
Equivalent diameter of grinding wheel
- d f :
-
Dynamic factor
- d s :
-
Diameter of grinding wheel
- d w :
-
Diameter of work-piece
- f a :
-
Fraction of abrasive grain that actively cut in grinding
- h :
-
Average un-deformed chip thickness
- h f :
-
Fluid convection factor
- k w :
-
Thermal conductivity
- l c :
-
Real contact length
- l fr :
-
Rough length of contact due to deflection
- l fs :
-
Smooth length of contact due to deflection
- l g :
-
Geometric length of contact
- n w :
-
Work-piece speed
- q ch :
-
Specific chip heat flux
- q f :
-
Specific coolant heat flux
- q t :
-
Total heat flux
- v r :
-
In-feed
- v 1 :
-
Poisson’s ratio of workpiece
- v 2 :
-
Poisson’s ratio of grinding wheel
- α :
-
Thermal diffusivity
- β w :
-
Material thermal property
- ρ w :
-
Density of work material
- θ m :
-
Maximum rise in surface temperature
- ε :
-
Fraction of energy entering into the work surface
- δ :
-
Deflection due to normal grinding force
- Ø :
-
Approach angle
References
Takazawa, K. (1966). Effects of grinding variables on surface structure of hardened steels. Bulletin of the Japan Society of Precision Engineering, 2, 14.
Kohli, S., Guo, C., & Malkin, S. (1995). Energy partition to the workpiece for grinding with aluminum oxide, and CBN abrasive wheels. ASME Journal of Engineering for Industry, 117, 160–168.
Lefebvrea, A., Vievilleb, P., Lipinskia, P., & Lescalier, C. (2006). Numerical analysis of grinding temperature measurement by the foil/workpiece thermocouple method. International Journal of Machine Tools and Manufacture, 46, 1716–1726.
Batako, A. D., Rowe, W. B., & Morgan, M. N. (2005). Temperature measurement in high efficiency deep grinding. International Journal of Machine Tools and Manufacture, 45, 1231–1245.
Rowe, W. B., Black, S. C. E., & Mills, B. (1996). Temperature control in CBN grinding. The International Journal of Advanced Manufacturing Technology, 12, 387–392.
Nosko, O., Nagamine, T., Nosko, A. L., Romashko, A. M., Mori, H., & Sato, Y. (2015). Measurement of temperature at sliding polymer surface by grindable thermocouples. Tribology International, 88, 100–106.
Ueda, T. (1986). Measurement of grinding temperature using infrared radiation pyrometer with optical fiber. Journal of Engineering for Industry, 108, 241–247.
Liu, D., Wang, G., Nie, Z., & Rong, Y. K. (2016). An in situ infrared temperature-measurement method with back focusing on surface for creep feed grinding. Measurement, 94, 645–652.
Mohammed, A., Folkes, J., & Chen, X. (2012). Detection of grinding temperatures using laser irradiation and acoustic emission sensing technique. Materials and Manufacturing Processes, 27(4), 395–400.
Xu, L. M., Li, R. Z., Xu, K. Z., Chai, Y. D., & Hu, D. J. (2011). Numerical simulation and experiments on high hardness coating grinding temperature field. Journal of Shanghai Jiaotong University, 45(11), 1705–1709.
Li, D. D., Kuang, J., Chen, Q. Q., Hu, D. J., & Xu, L. M. (2014). Temperature and phase transformation in grinding process of WC-Co coating. Journal of Shenyang University of Technology, 5, 010.
Shin, J. (2013) Device and method for measuring temperature using infrared array sensors. US20130230074.
Tsuzuki, T., Yamazaki, H., Takeno, H., & Takanori, Y. U. (2013). Infrared temperature measurement device. JP2013145153.
Kato, T., & Fujii, H. (1997). Temperature measurement of workpiece in surface grinding by PVD film method. Journal of Manufacturing Science and Engineering, 119, 689.
Comley, P., Walton, I., Jin, T., & Stephenson, D. J. (2006). A high material removal rate grinding process for the production of automotive crankshafts. Annals of the CIRP, 55, 347–350.
Guo, C., Wu, Y., Varghese, V., & Malkin, S. (1999). Temperature and energy partition for grinding with vitrified CBN wheels. Annals of the CIRP, 48(1), 247–250.
Kopac, J., & Krajnik, P. (2006). High-performance grinding—A review. Journal of Materials Processing Technology, 175, 278–284.
Agarwal, S., & Venkateshwar Rao, P. (2010). Grinding characteristics, material removal and damage formation mechanism in high removal rate grinding of silicon carbide. International Journal of Machine Tools and Manufacture, 50, 1077–1087.
Chen, X., Rowe, W. B., & Cai, R. (2002). Precision grinding using CBN wheel. International Journal of Machine Tools and Manufacture, 42, 585–593.
Malkin, S., & Cook, N. H. (1971). The wear of grinding wheels. Part 2—Fracture wear. Journal of Engineering for Industry, 93(4), 1129–1133.
Malkin, S., & Guo, C. (2008). Grinding technology—Theory and application of machining with abrasives (2nd ed.). New York: Industrial Press.
Rowe, W. B. (2009). Principle of modern grinding technology. Norwich: William Andrew Press.
Jaeger, J., & Carslaw, H. (1942). Moving sources of heat and the temperature of sliding contacts. New South Wales, 76(3), 202.
Hecker, R. L., Liang, S. Y., Wu, X. J., Xia, P., & Jin, D. G. W. (2007). Grinding force and power modeling based on chip thickness analysis. The International Journal of Advanced Manufacturing Technology, 33, 449–459.
Hecker, R. L., Ramoneda, I. M., & Liang, S. Y. (2003). Analysis of wheel topography and grit force for grinding process modeling. Journal of Manufacturing Process, 5(1), 13.
Qin, D., Wang, F., Xi, F., & Liu, Z. (2013). A theoretical model of grinding force and its simulation. Advanced Material Research, 690–693, 2395–2402.
Durgumahanti, S. P., Singh, V., & Venkateshwara Rao, P. (2010). A new model for grinding force prediction and analysis. International Journal of Machine Tools and Manufacture, 50, 231–240.
Vashista, M., & Paul, S. (2008). Study of the effect of process parameters in high-speed grinding on surface integrity by Barkhausen noise analysis. Institution of Mechanical Engineers, 222, 1625.
Kumar, S., Yadav, M., Agrawal, P., Zaheer Khan, M., & Vashista, M. (2011). Assessment of micohardness profile in grinding using Barkhausen noise technique at various analysis parameters. International Scholarly Research Network, 2011, Article ID 525078.
Siiriainen, J., Kendrish, S. J., Rickert, T. J., & Fix, R. M. (2008). Barkhausen noise and its use for quality control of the production of transmission gear. Advance Materials Research, 41–42, 407–419.
Neseli, S., Asilturk, D., & Celik, L. (2012). Determining the optimum process parameter for grinding operations using robust process. Journal of Mechanical Science and Technology, 26(11), 3587–3595.
Jagtap, K. R. (2012). Optimization of cylindrical grinding process parameters for AISI 1040 steel using Taguchi method. International Journal of Mechanical Engineering and Technology, 3(1), 47–56.
Malkin, S., & Guo, C. (2007). Thermal analysis of grinding. Annals of the CIRP, 56(2), 760–782.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Thanedar, A., Dongre, G.G. & Joshi, S.S. Analytical Modelling of Temperature in Cylindrical Grinding to Predict Grinding Burns. Int. J. Precis. Eng. Manuf. 20, 13–25 (2019). https://doi.org/10.1007/s12541-019-00037-9
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-019-00037-9