Abstract
As product development cycles are getting shorter, faster determination of proper process conditions for the new designs and materials is increasingly important. To respond these requirements, a significant effort for cutting experiments are being replaced by simulation-based approaches called Virtual Machining (VM). Simultaneously, metal parts with thinner and smaller features being frequently used in electronic products has increased demands for precision machining of thin walls, which is vulnerable to post-machining deformation (PMD). In this study, a simulation procedure is discussed to incorporate the prediction of PMD after metal cutting into VM environments. The method uses a combination of the residual stress and thermal analysis of cutting process and the structural analysis of machined part. Machining experiments have been performed to demonstrate the effectiveness of the proposed PMD simulation as a part of VM for initial selection of the machining conditions.
This is a preview of subscription content, log in via an institution to check access.
References
Heo, S., Jeong, Y. H., Min, B.-K., & Lee, S. J. (2009). Virtual EDM simulator: Three-dimensional gerometric simulation of micro-EDM milling processes. International Journal of Machine Tools and Manufacture, 49(12–13), 1029–1034.
Lee, W., Lee, C.-Y., & Min, B.-K. (2014). Simulation-based energy usage profiling of machine tool at the component level. International Journal of Precision Engineering and Manufacturing-Green Technology, 1(3), 183–189.
Kim, D. M., Kim, D. Y., & Park, H. W. (2018). The state of the art in FEM analysis technology of the machining process. Journal of the Korean Society for Precision Engineering, 35(3), 269–278.
Liu, C. R., & Guo, Y. B. (2000). Finite element analysis of the effect of sequential cuts and tool-chip friction on residual stresses in a machined layer. International Journal of Mechanical Sciences, 42(6), 1069–1086.
Zhang, H.-P., Zhang, Q.-Y., Ren, Y., Shay, T., & Liu, G.-L. (2018). Simulation and experiments on cutting forces and cutting temperature in high speed milling of 300 m steel under CMQL and dry conditions. International Journal of Precision Engineering and Manufacturing, 19(8), 1245–1251.
Lee, J., Kim, D.-H., & Lee, C.-M. (2015). A study on the thermal characteristics and experiments of high-speed spindle for machine tools. International Journal of Precision Engineering and Manufacturing, 16(2), 293–299.
Werke, M., Wretland, A., Ottosson, P., Holmberg, J., Machens, M., & Semere, D. (2018). Geometric distortion analysis using a combination of the contour method and machining simulation. In 51st CIRP conference on manufacturing systems, CIRP CMS 2018, 16 May 2018 through 18 May 2018 (pp. 1481–1486).
Miranda, M., Serje, D., Pacheco, J., & Bris, J. (2018). Tool edge radius wear and material removal rate performance charts for titanium micro-milling. International Journal of Precision Engineering and Manufacturing, 19(1), 79–84.
Altintas, Y., Brecher, C., Weck, M., & Witt, S. (2005). Virtual machine tool. CIRP Annals, 54(2), 115–138.
Acknowledgements
This work was supported by the Development of Core Industrial Technology Program (20000285, Development of a machine tool intelligence system based on virtual models of the machine structure, control system and cutting process) funded by the Ministry of Trade, Industry and Energy (MOTIE), Korea.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Park, SH., Nam, E., Gang, M.G. et al. Post-machining Deformation Analysis for Virtual Machining of Thin Aluminium Alloy Parts. Int. J. Precis. Eng. Manuf. 20, 687–691 (2019). https://doi.org/10.1007/s12541-019-00028-w
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-019-00028-w