A Comparative Study of AA6351 Mono-Composites Reinforced with Synthetic and Agro Waste Reinforcement

Regular Paper
  • 2 Downloads

Abstract

The use of industrial-agro wastes as reinforcements in the development of composites can be considered as a new inclination in the field of material research. The present investigation involves the development of AA6351 mono-composites with various weight percentages (2wt.%, 4wt.%, 6wt.% and 8wt.%) of silicon carbide (SiC) and rice husk ash (RHA) as reinforcement using stir casting technique. The physical, microstructural, mechanical and tribolological behaviour of the developed composites were examined for the both type of the composites. An increase of 1.08% in density, 37% in hardness and 39% in tensile strength was recorded for the composites developed with silicon carbide as reinforcement and a decrease in density of 3.9%, an improvement of 16% in hardness and 21% in tensile strength was indicated for the composites reinforced with rice husk ash as reinforcement. The results also revealed a uniform distribution of the reinforcement and improved wear resistance for the both set of the composites. The characterization results exhibited that even the performance of the composites with SiC as reinforcement is better than the performance of the composites with RHA as reinforcement but RHA can be suitably applied as reinforcement for the development of low density AA6351/RHA green composites

Keywords

Rice husk ash Metal matrix composites AA6351 aluminium alloy Stir casting Density 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Surappa, M. K., “Aluminium Matrix Composites: Challenges and Opportunities,” Sadhana, Vol. 28, Nos. 1-2, pp. 319–334, 2003.CrossRefGoogle Scholar
  2. 2.
    Prasad, S. and Asthana, R., “Aluminum Metal-Matrix Composites for Automotive Applications: Tribological Considerations,” Tribology Letters, Vol. 17, No. 3, pp. 445–453, 2004.CrossRefGoogle Scholar
  3. 3.
    Das, D. K., Mishra, P. C., Singh, S., and Pattanaik, S., “Fabrication and Heat Treatment of Ceramic-Reinforced Aluminium Matrix Composites-A Review,” International Journal of Mechanical and Materials Engineering, Vol. 9, No. 1, Paper No. 6, 2014.Google Scholar
  4. 4.
    Dobrzanski, L., Kremzer, M., Nowak, A., and Nagel, A., “Aluminium Matrix Composites Fabricated by Infiltration Method,” Archives of Materials Science and Engineering, Vol. 36, No. 1, pp. 5–11, 2009.Google Scholar
  5. 5.
    Albiter, A., Contreras, A., Salazar, M., and Gonzalez-Rodriguez, J., “Corrosion Behaviour of Aluminium Metal Matrix Composites Reinforced with TiC Processed by Pressureless Melt Infiltration,” Journal of Applied Electrochemistry, Vol. 36, No. 3, pp. 303–308, 2006.CrossRefGoogle Scholar
  6. 6.
    Aigbodion, V. and Hassan, S., “Effects of Silicon Carbide Reinforcement on Microstructure and Properties of Cast Al-Si-Fe/ SiC Particulate Composites,” Materials Science and Engineering: A, Vol. 447, Nos. 1-2, pp. 355–360, 2007.CrossRefGoogle Scholar
  7. 7.
    Su, H., Gao, W., Feng, Z., and Lu, Z., “Processing, Microstructure and Tensile Properties of Nano-Sized Al2O3 Particle Reinforced Aluminum Matrix Composites,” Materials & Design (1980-2015), Vol. 36, pp. 590–596, 2012.CrossRefGoogle Scholar
  8. 8.
    Zhang, D. L., Brindley, C., and Cantor, B., “The Microstructures of Aluminium Alloy Metal-Matrix Composites Manufactured by Squeeze Casting,” Journal of Materials Science, Vol. 28, No. 8, pp. 2267–2272, 1993.CrossRefGoogle Scholar
  9. 9.
    Vijayaram, T., Sulaiman, S., Hamouda, A., and Ahmad, M., “Fabrication of Fiber Reinforced Metal Matrix Composites by Squeeze Casting Technology,” Journal of Materials Processing Technology, Vol. 178, Nos. 1-3, pp. 34–38, 2006.CrossRefGoogle Scholar
  10. 10.
    Urena, A., Gomez de Salazar, J., and Escalera, M., “Diffusion Bonding of an Aluminum-Copper Alloy Reinforced with Silicon Carbide Particles (AA2014/SiC/13p) Using Metallic Interlayers,” Scripta Materialia, Vol. 35, No. 11, pp. 1285–1293, 1996.CrossRefGoogle Scholar
  11. 11.
    Zhang, X.-P., Ye, L., Mai, Y.-W., Quan, G.-F., and Wei, W., “Investigation on Diffusion Bonding Characteristics of SiC Particulate Reinforced Aluminium Metal Matrix Composites (Al/SiCp-MMC),” Composites Part A: Applied Science and Manufacturing, Vol. 30, No. 12, pp. 1415–1421, 1999.CrossRefGoogle Scholar
  12. 12.
    Liu, Y. B., Lim, S. C., Lu, L., and Lai, M. O., “Recent Development in the Fabrication of Metal Matrix-Particulate Composites Using Powder Metallurgy Techniques,” Journal of Materials Science, Vol. 29, No. 8, pp. 1999–2007, 1994.CrossRefGoogle Scholar
  13. 13.
    Feng, C. and Froyen, L., “Formation of Al3Ti and Al2O3 from an Al-TiO2 System for Preparing In-Situ Aluminium Matrix Composites,” Composites Part A: Applied Science and Manufacturing, Vol. 31, No. 4, pp. 385–390, 2000.CrossRefGoogle Scholar
  14. 14.
    Xie, F. and Xue, Z.-H., “Characterizing an in situ TiB2 Particulates Reinforced Aluminium-Based Composite and Its Heat Treatment,” Physics Procedia, Vol. 50, pp. 13–18, 2013.CrossRefGoogle Scholar
  15. 15.
    Sharma, P., Khanduja, D., and Sharma, S., “Tribological and Mechanical Behavior of Particulate Aluminum Matrix Composites,” Journal of Reinforced Plastics and Composites, Vol. 33, No. 23, pp. 2192–2202, 2014.CrossRefGoogle Scholar
  16. 16.
    Hashim, J., Looney, L., and Hashmi, M., “Metal Matrix Composites: Production by the Stir Casting Method,” Journal of Materials Processing Technology, Vols. 92-93, pp. 1–7, 1999.CrossRefGoogle Scholar
  17. 17.
    Shorowordi, K., Laoui, T., Haseeb, A., Celis, J.-P., and Froyen, L., “Microstructure and Interface Characteristics of B4C, SiC and Al2O3 Reinforced Al Matrix Composites: A Comparative Study,” Journal of Materials Processing Technology, Vol. 142, No. 3, pp. 738–743, 2003.CrossRefGoogle Scholar
  18. 18.
    Sharma, P., Sharma, S., and Khanduja, D., “Effect of Graphite Reinforcement on Physical and Mechanical Properties of Aluminum Metal Matrix Composites,” Particulate Science and Technology, Vol. 34, No. 1, pp. 17–22, 2016.CrossRefGoogle Scholar
  19. 19.
    Debnath, S., Lancaster, L., and Lung, M., “Utilization of Agro-Industrial Waste in Metal Matrix Composites: Towards Sustainability, World Academy of Science,” Engineering and Technology, Vol. 73, pp. 1136–1144, 2013.Google Scholar
  20. 20.
    Arora, G. and Sharma, S., “A Review on Monolithic and Hybrid Metal-Matrix Composites Reinforced with Industrial-Agro Wastes,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, Vol. 39, No. 11, pp. 4819–4835, 2017.CrossRefGoogle Scholar
  21. 21.
    Giddel, M. and Jivan, A., “Waste to Wealth, Potential of Rice Husk in India a Literature Review,” Proc. of International Conference on Cleaner Technologies and Environmental Management PEC, Pondicherry, pp. 4–6, 2007.Google Scholar
  22. 22.
    Kumar, A., Mohanta, K., Kumar, D., and Parkash, O., “Properties and Industrial Applications of Rice Husk: A Review,” Vol. 2, No. 10, pp. 86–90, 2012.Google Scholar
  23. 23.
    Krishna, G. G., Reddy, P. R., and Hussain, M. M., “Experimental Investigation of Tensile Strength and Deflection Characteristics of Friction Stir Welded Aluminum AA 6351 Alloy Joint,” IOSR Journal of Mechanical and Civil Engineering, Vol. 7, No. 5, pp. 01–06, 2013.CrossRefGoogle Scholar
  24. 24.
    Prasad, D. S., and Krishna, A. R., “Production and Mechanical Properties of A356. 2/RHA Composites,” International Journal of Advanced Science and Technology, Vol. 33, pp. 51–58, 2011.Google Scholar
  25. 25.
    Alaneme, K. K., “Mechanical Behaviour of Cold Deformed and Solution Heat-Treated Alumina Reinforced AA 6063 Metal Matrix Composites,” The West Indian Journal of Engineering, Vol. 35, No. 2, pp. 31–35, 2013.Google Scholar
  26. 26.
    Aigbodion, V. S., “Development of Al-Si-Fe/Rice Husk Ash Particulate Composites Synthesis by Double Stir Casting Method,” Usak University Journal of Material Sciences, Vol. 1, No. 2, pp. 187–197, 2012.Google Scholar

Copyright information

© Korean Society for Precision Engineering and Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Department of Mechanical Engineering, School of EngineeringGautam Buddha UniversityGreater NoidaIndia
  2. 2.Delhi Institute of Tool Engineering, OkhlaNew DelhiIndia

Personalised recommendations