Skip to main content

Development of integrated stub end by spinning process

Abstract

The stub end is used to connect pipes in piping arrangement. Generally the components are manufactured by welding two subcomponents. But this method requires a large amount of time and money and also has a problem due to welding process like thermal deformation or embrittlement at heat affected zone. The spinning process, eco-friendly incremental process, was adopted to develop stub end without weld. It allows the component to be produced by non-welding with low cost and short process time. The major goal of this study is to develop optimum spinning process for manufacturing integrated stub end in keeping with the dimensions presented in the code. The suitable multi-step spinning process and rollers which can set required shapes and dimensions at each location of the component were designed by simulation. Base on the result of analysis and test, the 4 inch’s stub end specified in the code was developed. The spinning machine was also developed to manufacture specimens. Hardness was measured to predict the strength of flange part. Along with the shapes, all dimensions at each part were satisfied the required values.

This is a preview of subscription content, access via your institution.

References

  1. 1.

    Kim, J. S., Cho, J. R., and Jeong, H. S., “Manufacturing Method of Long-Neck Flange,” KOR Patent, No.100688066, 2007.

    Google Scholar 

  2. 2.

    Kastuteru, A., “Manufacturing Method of Lap-Joint Pipe,” JP Patent, Shou64-71527, 1989 (in Japanese).

    Google Scholar 

  3. 3.

    ASME, “Factory-Made Wrought Buttwelding Fittings,” ASME B16.9, 2007.

    Google Scholar 

  4. 4.

    Jeong, H. S., Son, C. W., Oh, J. S., Choi, S. K., and Cho, J. R.., “Friction Welding Process Analysis of Piston Rod in Marine Diesel Engine and Mechanical Properties of Welded Joint,” Transactions on Materials Processing, vol. 20, no. 3, pp. 236–242, 2011.

    Article  Google Scholar 

  5. 5.

    Park, H. W., Kwon, J. H., Kim, J. S., and Cho, J. R.., “The Development of Manufacturing Method of Integrated Lap Joint by Spinning Process,” Proc. of the Korean Society for Technology of Plasticity Spring Conference, pp. 163–166, 2010.

    Google Scholar 

  6. 6.

    Park, J. E., Han, C. S., Choi, S., Kim, S. S., and Na, K. H., “The Spinnability of Multi-step Cylindrical Cup in Spinning Process,” Proc. of KSPE Spring Conference, pp. 1016–1020, 2001.

    Google Scholar 

  7. 7.

    Kang, J. S., Park, G. S., and Kang, E. S., “Design of Hydraulic & Control System for the Disc Spinning Machine,” J. Korean Soc. Precis. Eng., vol. 19, no. 9, pp. 157–165, 2002.

    Google Scholar 

  8. 8.

    Lee, H. W., Hwang, D. W., Song, S. A., and Kim, C., “A Study on the Improvement of Hot Spinning Process for Weight Lighting of CNG Vessel (Type II),” Proc. of KSPE Spring Conference, pp. 135–136, 2012.

    Google Scholar 

  9. 9.

    Jeong, D. S., Kim, S. T., Choi, D. B., Ye, S. B., and Seol, S. S., “A Study on the Thermal Characteristics of Spindle for the Spinning Machine,” Proc. of KSPE Spring Conference, pp. 565–569, 2005.

    Google Scholar 

  10. 10.

    Kim, Y. H., Park, J. W., and Cho, H. S., “An Analysis of Tube Spinning for Shock Absorber on Vehicles,” J. Korean Soc. Precis. Eng., vol. 17, no. 3, pp. 33–38, 2000.

    Google Scholar 

Download references

Author information

Affiliations

Authors

Corresponding author

Correspondence to Jong-Rae Cho.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Gwak, GY., Jeon, JW., Cho, JR. et al. Development of integrated stub end by spinning process. Int. J. Precis. Eng. Manuf. 16, 1473–1477 (2015). https://doi.org/10.1007/s12541-015-0195-x

Download citation

Keywords

  • Stub end
  • Spinning
  • ALE method
  • Right-angle
  • Roundness