Abstract
Magnetorheological fluid based finishing process is particularly useful for finishing of optical materials. Magnetorheological (MR) fluid consists of magnetic particles, abrasive particles, carrier fluid such as water or oil, and additive. Under the influence of magnetic field, magnetic particles form chain like structure and they support abrasive particles to perform finishing. Stiffness and abrasive holding power of MR fluid significantly depend on the size of magnetic particles while concentration and type of abrasive particles are also important parameters which affect the quality of finished surface. An experimental investigation is carried out to study the effect of size, concentration and type of abrasive particles as well as the size of magnetic particles on material removal rate and % change in surface roughness (Ra) of final finished surface of single crystal silicon workpiece. A rheological study in terms of yield stress is also carried out to analyze MR fluid behavior under magnetic field.
Similar content being viewed by others
References
Bayoumi, M. R. and Abdellatif, A. K., “Effect of Surface Finish on Fatigue Strength,” Engineering Fracture Mechanics, Vol. 51, No. 5, pp. 861–870, 1995.
Khounsary, A., Fernandez, P., Assoufid, L., Mills, D., Walters, D., Schwartz, J., and Robichaud, J., “Design, Fabrication, and Evaluation of an Internally Cooled Silicon Carbide Mirror,” Review of Scientific Instruments, Vol. 73, No. 3, pp. 1537–1540, 2002.
Jung, B., Jang, K. I., Min, B. K., Lee, S. J., and Seok, J., “Magnetorheological Finishing Process for Hard Materials Using Sintered Iron-CNT Compound Abrasives,” International Journal of Machine Tools and Manufacture, Vol. 49, No. 5, pp. 407–418, 2008.
Kim, T.-W. and Kwak, J.-S., “A Study on Deburring of Magnesium Alloy Plate by Magnetic Abrasive Polishing,” Int. J. Precis. Eng. Manuf., Vol. 11, No. 2, pp. 189–194, 2010.
Mun, S.-D., “Micro Machining of High-Hardness Materials Using Magnetic Abrasive Grains,” Int. J. Precis. Eng. Manuf., Vol. 11, No. 5, pp. 763–770, 2010.
Rosensweig, R. E., “Ferrohydrodynamics,” Dover, pp. 149–156, 1985.
Sidpara, A., Das, M., and Jain, V. K., “Rheological Characterization of Magnetorheological Finishing Fluid,” Journal of Materials and Manufacturing Processes, Vol. 24, No. 12, pp. 1467–1478, 2009.
Sidpara, A. and Jain, V. K., “Nano-level finishing of single crystal silicon blank using magnetorheological finishing process,” Tribology International, Vol. 47, pp. 159–166, 2011.
Sidpara, A. and Jain, V. K., “Effect of fluid composition on nanofinishing of single-crystal silicon by magnetic field-assisted finishing process,” International Journal of Advanced Manufacturing Technology, Vol. 55, No. 1–4, pp. 243–252, 2011.
Shorey, A. B., Jacobs, S. D., Kordonski, W. I., and Gans, R. F., “Experiments and Observations Regarding the Mechanisms of Glass Removal in Magnetorheological Finishing,” Applied Optics, Vol. 40, No. 1, pp. 20–33, 2001.
Bombard, A. J. F., Knobel, M., Alcantara, M. R., and Joekes, I., “Evaluation of Magnetorheological Suspensions Based on Carbonyl Iron Powders,” Journal of Intelligent Material Systems and Structures, Vol. 13, No. 7, pp. 471–478, 2002.
Gorodkin, S. R., James, R. O., and Kordonski, W. I., “Magnetic Properties of Carbonyl Iron Particles in Magnetorheological Fluids,” Journal of Physics: Conference Series, Vol. 149, No. 1, Paper No. 012051, 2009.
Huang, J., Zhang, J. Q., and Liu, J. N., “Effect of Magnetic Field on Properties of MR Fluid,” International Journal of Modern Physics B, Vol. 19, No. 1–3, pp. 597–601, 2005.
Jha, S. and Jain, V. K., “Modeling and Simulation of Surface Roughness in Magnetorheological Abrasive Flow Finishing (MRAFF) Process,” Wear, Vol. 261, No. 7–8, pp. 856–866, 2006.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Sidpara, A., Jain, V.K. Experimental investigations into surface roughness and yield stress in magnetorheological fluid based nano-finishing process. Int. J. Precis. Eng. Manuf. 13, 855–860 (2012). https://doi.org/10.1007/s12541-012-0111-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-012-0111-6