Abstract
The presence of weak planes in most rock masses reduces their strength and changes their mechanical behavior. Jaeger’s plane of weakness theory is a simple model for predicting the strength of jointed rock samples. This model proposes a U-shaped curve for the strength of the jointed rock samples. In this paper, using the discrete element method, several two-dimensional models of the jointed rock samples are analyzed, and their results are compared with Jaeger’s plane of weakness theory. According to the results, if the sample has one or two parallel joints, the strength obtained from the numerical method corresponds to the analytical model. However, if the sample has two intersecting symmetrical joints, the concentration of stress created at the vertices of the rock blocks increases the strength of the sample, In this case, the sample strength is 80% on average higher than that of the sample with a single joint. If the sample has three or four intersecting joints with an angle of 30° to each other, the strength of the sample based on numerical solution is 36% and 40% less than the theoretical solution, respectively. In this case, because the sample is divided into several small parts, the strength of the sample is reduced and less than the theoretical model. Numerical analysis provides strength and failure mode for jointed rock samples more accurately, which will certainly be useful in designing underground structures located in jointed rock environments.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Arora VK (1987) Strength and deformational behaviour of jointed rocks. Ph.D. thesis, submitted to Ind. Inst. Technol., New Delhi.
Barton NR (1972) A model study of rock-joint deformation. International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts 9(5):579–582. https://doi.org/10.1016/0148-9062(72)90010-1
Bieniawski ZT (1973) Engineering classification of jointed rock masses. Civil Engineer in South Africa 15(12):335e44
Brown ET, Trollope DH (1970) Strength of a model of jointed rock. J. Soil Mech. Found. Div. 96(2):685–704
Cazacu O, Cristescu ND (1999) A paraboloid failure surface for transversely isotropic materials. J Mech Mater. 31:381–393. https://doi.org/10.1016/S0167-6636(99)00008-3
Chong WL, Haque A, Gamage RP, Shahinuzzaman A (2013) Modelling of intact and jointed mudstone samples under uniaxial and triaxial compression. Arab J Geosci 6:1639–1646. https://doi.org/10.1007/s12517-011-0463-8
Colak K, Unlu T (2004) Effect of transverse anisotropy on the Hoek-Brown strength parameter ‘mi’ for intact rocks. International Journal of Rock Mechanics and Mining Sciences 41:1045e1052–1045e1052. https://doi.org/10.1016/j.ijrmms.2004.04.004
Duveau G, Shao JF, Henry JP (1998) Assessment of some failure criteria for strongly anisotropic geomaterials. Mech. Cohesive-Frictional Mater. Vol. 3:1–26. https://doi.org/10.1002/(SICI)1099-1484(199801)3:1%3C1::AID-CFM38%3E3.0.CO;2-7
Einstein HH, Hirschfeld RC (1973) Model studies in mechanics of jointed rock. J Soil Mech Found Div 99(3):229–248
Goldstein M, Goosev B, Pyrogovsky A, Tulinov R, Turovskaya A (1966) Investigations of mechanical properties of cracked rock. Proceedings of the first international congress on rock mechanics, Lisbon, In, pp 521–524
Halakatevakis N, Sofianos AI (2010) Strength of a blocky rock mass based on an extended plane of weakness theory. International Journal of Rock Mechanics and Mining Sciences 47:568–582. https://doi.org/10.1016/j.ijrmms.2010.01.008
Hayashi M (1966) Strength and dilatancy of brittle jointed mass- the extreme stochastic and anisotropic failure mechanism. Proc., 1 st Int. Congress on Rock Mechanics, Libson, I, 295-302.
Hoek E (2007) Practical rock engineering, Evert Hoek Consulting Engineering Inc. North Vancouver, British Columbia, Canada
ITASCA Consulting Group (2014) UDEC Universal Distinct Element Code, Version 6.0, Vol. 1, 2 and 3, User’s Manual.
Jaeger JC (1960) Shear failure of anisotropic rocks. Geological Magazine 97(1):65–72
Lee Y-K, Pietruszczak S (2008) Application of critical plane approach to the prediction of strength anisotropy in transversely isotropic rock masses. International Journal of Rock Mechanics and Mining Sciences 45(4):513–523. https://doi.org/10.1016/j.ijrmms.2007.07.017
McLamore RT, Gray KE (1967) A strength criterion for anisotropic rocks based upon experimental observations. SPE Annual Meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers, 19–23 February 1967, Los Angeles, paper SPE 1721. https://doi.org/10.2118/1721-MS
Mróz Z, Maciejewski J (2011) Critical plane approach to analysis of failure criteria for anisotropic geomaterials. In: Wan R, Alsaleh M, Labuz J (eds) Bifurcations, Instabilities and Degradations in Geomaterials. Springer Series in Geomechanics and Geoengineering, vol 0. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-642-18284-6_5
Noorian Bidgoli M, Jing L (2014) Anisotropy of strength and deformability of fractured rocks. Journal of Rock Mechanics and Geotechnical Engineering 6(2):156–164. https://doi.org/10.1016/j.jrmge.2014.01.009
Nova R (1980) The failure of transversely isotropic rocks in triaxial compression. Int J Rock Mech Min Sci. 17(6) December 1980:325–332. https://doi.org/10.1016/0148-9062(80)90515-X
Pariseau WG (1968) Plasticity theory for anisotropic rocks and soils. In: Proceedings of the 10th US Symposium on Rock Mechanics, 20-22 May, Austin, Texas, paper ARMA 68-0267.
Park B, Min K-B, Thompson N, Horsrud P (2018) Three-dimensional bonded-particle discrete element modeling of mechanical behavior of transversely isotropic rock. International Journal of Rock Mechanics and Mining Sciences 110:120–132. https://doi.org/10.1016/j.ijrmms.2018.07.018
Pei J (2008) Strength of transversely isotropic rocks. PhD Thesis, MIT.
Ramamurthy T, Rao GV, Singh J (1988) A strength criterion for transversely isotropic rocks. In: Proc. of the Fifth Australia New Zealand Conference on Geomechanics, Sydney, vol. 1, pp. 253e257.
Ramamurthy T, Venkatappa RG, Singh J (1993) Engineering behaviour of phyllites. Engineering Geology 33:209e225–209e225. https://doi.org/10.1016/0013-7952(93)90059-L
Sainsbury BL, Sainsbury DP (2017) Practical use of the ubiquitous-joint constitutive model for the simulation of anisotropic rock masses. Rock Mech Rock Eng 50:1507–1528. https://doi.org/10.1007/s00603-017-1177-3
Saroglou H, Tsiambaos G (2008) A modified Hoek–Brown failure criterion for anisotropic intact rock. International Journal of Rock Mechanics and Mining Sciences 45(2):223–234. https://doi.org/10.1016/j.ijrmms.2007.05.004
Shen J, Shu Z, Cai M, Du S (2020) A shear strength model for anisotropic blocky rock masses with persistent joints. International Journal of Rock Mechanics and Mining Sciences 134:104430. https://doi.org/10.1016/j.ijrmms.2020.104430
Singh J, Ramamurthy T, Rao G (1989) Strength anisotropies in rocks, Indian Geotech. J. 19(2):147–166
Singh M, Rao K, Ramamurthy T (2002) Strength and deformational behaviour of a jointed rock mass. Rock Mech Rock Engng 35:45–64. https://doi.org/10.1007/s006030200008
Single B, Goel RK, Mehrotra VK, Garg SK, Allu MR (1998) Effect of intermediate principal stress on strength of anisotropic rock mass. Tunnelling and Underground Space Technology 13(1):71–79. https://doi.org/10.1016/S0886-7798(98)00023-6
Sun Y, Zhang P, Yan W, Yan F, Wu J (2020) Compressive deformation characteristics of crushed sandstone based on multiple experimental factors. Archives of Mining Sciences 65(No 1):129–146. https://doi.org/10.24425/ams.2020.132711
Tajduś K (2009) New method for determining the elastic parameters of rock mass layers in the region of underground mining influence. International Journal of Rock Mechanics and Mining Sciences 46(8):1296–1305. https://doi.org/10.1016/j.ijrmms.2009.04.006
Tien YM, Kuo MC, Juang CH (2006) An experimental investigation of the failure mechanism of simulated transversely isotropic rocks. International Journal of Rock Mechanics and Mining Sciences 43(8):1163–1181. https://doi.org/10.1016/j.ijrmms.2006.03.011
Verma AK, Singh TN (2010) Modeling of a jointed rock mass under triaxial conditions. Arab J Geosci 3:91–103. https://doi.org/10.1007/s12517-009-0063-z
Walsh JB, Brace WF (1964) A fracture criterion for brittle anisotropic rock. J. Geophys. Res. 69(16):3449–3456. https://doi.org/10.1029/JZ069i016p03449
Wang Q, Wang J, Ye Y, Jiang W, Yao N (2020) Failure characteristics and strength model of composite rock samples in contact zone under compression. Archives of Mining Sciences 65(No 2):347–361. https://doi.org/10.24425/ams.2020.133197
Wasantha PLP, Ranjith PG, Haque A, Kodikara J, Bouazza A (2011) Implications of joint properties on the strength of a jointed rock mass. Advances in Unsaturated Soil, Geo-Hazard, and Geo-Environmental Engineering:258–266. https://doi.org/10.1061/47628(407)33
Wasantha PLP, Ranjith PG, Viete DR (2014) Effect of joint orientation on the hydromechanical behavior of singly jointed sandstone experiencing undrained loading. J Geophys Res-Sol Ea 119(3):1701–1717. https://doi.org/10.1002/2013JB010600
Yang XX, Jing HW, Tang CA, Yang SQ (2017) Effect of parallel joint interaction on mechanical behavior of jointed rock mass models. International Journal of Rock Mechanics and Mining Sciences 92:40–53. https://doi.org/10.1016/j.ijrmms.2016.12.010
Zhang G-q (2009) Rock failure with weak planes by self-locking concept. International Journal of Rock Mechanics and Mining Sciences 46(6):974–982. https://doi.org/10.1016/j.ijrmms.2009.03.009
Zhang L, Zhu H (2007) Three-dimensional Hoek-Brown strength criterion for rocks. Int J Geotech Geoenv Eng. 133(9):1128–1135. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:9(1128)
Zheng Q, Liu E, Sun P, Liu M, Yu D (2020) Dynamic and damage properties of artificial jointed rock samples subjected to cyclic triaxial loading at various frequencies. International Journal of Rock Mechanics and Mining Sciences 128:104243. https://doi.org/10.1016/j.ijrmms.2020.104243
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no competing interests.
Additional information
Responsible Editor: Zeynal Abiddin Erguler
Rights and permissions
About this article
Cite this article
As’habi, F., Lakirouhani, A. Numerical modeling of jointed rock samples under unconfined and confined conditions to study peak strength and failure mode. Arab J Geosci 14, 174 (2021). https://doi.org/10.1007/s12517-021-06569-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s12517-021-06569-7