Abstract
Fault gouge, located in highly deformed fault cores, shows substantial particle size reduction and loss of crystallinity, which could affect the physicochemical properties and thus control the slip behavior and earthquake stability of a fault. To systematically investigate the effect of deformed fault gouge on fault slip behavior in laboratory-scale experiments, a fault gouge analog with variable particle size and crystallinity is required. However, the systematic study for formation of a fault gouge analog (i.e., controlling the particle size and crystallinity) was not performed well. In this study, we investigated the effect of the rotation speed of a high-energy ball mill on particle size reduction rate and degree of amorphization. As the rotation speed increased from 500 to 2000 rpm, the comminution rate linearly increased, and reached a reduced particle size limit. The degree of amorphization and its rate also increased with increasing rotation speed. Upon grinding, the X-ray diffraction (XRD) peaks markedly decreased and reached critical amorphization points within 120 min, except for the case of grinding with a rotation speed of 500 rpm. Talc ground with a rotation speed of 500 rpm did not reach steady-state in mechanical amorphization after 360 min of grinding, thus necessitating prolonged grinding for further amorphization. A comparison of talc powders having similar specific surface areas, but ground at different rotation speeds, shows that grinding with a higher rotation speed for a shorter duration preserves the crystalline structure relatively well compared with grinding at a lower rotation speed for a longer duration. These results indicate that optimizing the grinding rotation speed facilitates the formation of talc fault gouge analogs with systematically varying particle size and crystallinity. The specific surface area of talc increased from 6.1 to 365 m2/g, and the degree of crystallinity decreased from approximately 75% to 11%. Our results indicate that an artificial talc fault gouge can be prepared by varying the particle size and crystallinity using a high-energy ball mill.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Boutareaud, S., Hirose, T., Andréani, M., Pec, M., Calugaru, D.-G., Boullier, A.-M., and Doan, M.-L., 2012, On the role of phyllosilicates on fault lubrication: insight from micro- and nanostructural investigations on talc friction experiments. Journal of Geophysical Research: Solid Earth, 117, B08408. https://doi.org/10.1029/2011JB009006
Brandes, C. and Tanner, D.C., 2020, Fault mechanics and earthquakes. In: Tanner, D. and Brandes, C. (eds.), Understanding Faults: Detecting, Dating, and Modeling. Elsevier, p. 11–80. https://doi.org/10.1016/B978-0-12-815985-9.00002-3
Caban-Nevarez, R. and Perez, O.J.P., 2015, Size-dependence hydrophobicity in nanocrystalline talc produced by high-intensity planetary ball milling. MRS Online Proceedings Library Archive, 1805. https://doi.org/10.1557/opl.2015.723
Caine, J.S., Evans, J.P., and Forster, C.B., 1996, Fault zone architecture and permeability structure. Geology, 24, 1025–1028.
Chen, X., Elwood Madden, A.S., and Reches, Z.E., 2017, The frictional strength of talc gouge in high-velocity shear experiments. Journal of Geophysical Research: Solid Earth, 122, 3661–3676. https://doi.org/10.1002/2016JB013676
Chen, Y., Lian, X., Li, Z., Zheng, S., and Wang, Z., 2015, Effects of rotation speed and media density on particle size distribution and structure of ground calcium carbonate in a planetary ball mill. Advanced Powder Technology, 26, 505–510.
Delle Piane, C., Clennell, M.B., Keller, J.V, Giwelli, A., and Luzin, V., 2017, Carbonate hosted fault rocks: a review of structural and microstructural characteristic with implications for seismicity in the upper crust. Journal of Structural Geology, 103, 17–36.
Dellisanti, F., Valdré, G., and Mondonico, M., 2009, Changes of the main physical and technological properties of talc due to mechanical strain. Applied Clay Science, 42, 398–404.
Filio, J.M., Sugiyama, K., Saito, F., and Waseda, Y., 1994, A study on talc ground by tumbling and planetary ball mills. Powder Technology, 78, 121–127.
Han, R., Shimamoto, T., Hirose, T., Ree, J.H., and Ando, J., 2007, Ultralow friction of carbonate faults caused by thermal decomposition. Science, 316, 878–881.
Hirauchi, K.-I., den Hartog, S.A.M., and Spiers, C.J., 2013, Weakening of the slab-mantle wedge interface induced by metasomatic growth of talc. Geology, 41, 75–78.
Hirono, T., Kaneki, S., Ishikawa, T., Kameda, J., Tonoike, N., Ito, A., and Miyazaki, Y., 2020, Generation of sintered fault rock and its implications for earthquake energetics and fault healing. Communications Earth & Environment, 1, 3.
Hirono, T., Tanikawa, W., Honda, G., Kameda, J., Fukuda, J.-i., and Ishikawa, T., 2013, Importance of mechanochemical effects on fault slip behavior during earthquakes. Geophysical Research Letters, 40, 2988–2992.
Horváth, E., Frost, R.L., Makó, É., Kristóf, J., and Cseh, T., 2003, Thermal treatment of mechanochemically activated kaolinite. Thermochimica Acta, 404, 227–234.
Kim, H.N., Kim, J.W., Kim, M.S., Lee, B.H., and Kim, J.C., 2019, Effects of ball size on the grinding behavior of talc using a high-energy ball mill. Minerals, 9, 668.
Kim, H.N., So, B.-D., Kim, M.S., Han, K.S., and Oh, S.B., 2021, Seismic fault weakening via CO2 pressurization enhanced by mechanical deformation of dolomite fault gouges. Geology, 49, 1245–1249.
Kim, K.Y., Suh, H.S., Yun, T.S., Moon, S.-W., and Seo, Y.-S., 2016, Effect of particle shape on the shear strength of fault gouge. Geosciences Journal, 20, 351–359.
Kita, I., Matsuo, S., and Wakita, H., 1982, H2 generation by reaction between H2O and crushed rock: an experimental study on H2 degassing from the active fault zone. Journal of Geophysical Research: Solid Earth, 87, 10789–10795.
Mair, K. and Abe, S., 2011, Breaking up: comminution mechanisms in sheared simulated fault gouge. Pure and Applied Geophysics, 168, 2277–2288.
Makó, É., Frost, R.L., Kristóf, J., and Horváth, E., 2001, The effect of quartz content on the mechanochemical activation of kaolinite. Journal of Colloid and Interface Science, 244, 359–364.
Mio, H., Kano, J., Saito, F., and Kaneko, K., 2002, Effects of rotational direction and rotation-to-revolution speed ratio in planetary ball milling. Materials Science and Engineering: A, 332, 75–80.
Mio, H., Kano, J., Saito, F., and Kaneko, K., 2004, Optimum revolution and rotational directions and their speeds in planetary ball milling. International Journal of Mineral Processing, 74, S85–S92.
Moore, D.E. and Lockner, D.A., 2004, Crystallographic controls on the frictional behavior of dry and water-saturated sheet structure minerals. Journal of Geophysical Research: Solid Earth, 109, B03401. https://doi.org/10.1029/2003JB002582
Moore, D.E. and Lockner, D.A., 2011, Frictional strengths of talc-serpentine and talc-quartz mixtures. Journal of Geophysical Research: Solid Earth, 116, B01403. https://doi.org/10.1029/2010JB007881
Salili, S.M., Ataie, A., and Sadighi, Z., 2011, Effect of ball size and ball to powder ratio variation on crystallite size and formation of nanocrystalline materials in planetary ball mill. AIP Conference Proceedings, 1400, 127–130. https://doi.org/10.1063/1.3663098
Sanchez-Soto, P.J., Wiewióra, A., Avilés, M.A., Justo, A., Pérez-Maqueda, L.A., Pérez-Rodríguez, J.L., and Bylina, P., 1997, Talc from Puebla de Lillo, Spain. II. effect of dry grinding on particle size and shape. Applied Clay Science, 12, 297–312.
Saruwatari, K., Kameda, J., and Tanaka, H., 2004, Generation of hydrogen ions and hydrogen gas in quartz-water crushing experiments: an example of chemical processes in active faults. Physics and Chemistry of Minerals, 31, 176–182.
Shin, H., Lee, S., Jung, H.S., and Kim, J.-B., 2013, Effect of ball size and powder loading on the milling efficiency of a laboratory-scale wet ball mill. Ceramics International, 39, 8963–8968.
Viti, C., 2011, Exploring fault rocks at the nanoscale. Journal of Structural Geology, 33, 1715–1727.
Acknowledgments
This work was supported by the research grant of the Kongju National University awarded to H.N. Kim (2019-0207-01).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Kim, H.N., Kim, J.W., So, BD. et al. Formation of talc fault gouge analog using high-energy ball mill. Geosci J 26, 703–713 (2022). https://doi.org/10.1007/s12303-022-0012-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12303-022-0012-3