Skip to main content
SpringerLink
Log in

Testing of rock climbing anchors in weak sandstone

  • Original Article
  • Published:
Sports Engineering Aims and scope Submit manuscript

Abstract

Climbers sometimes rely on fixed anchors which are secured in drilled holes by mechanical expansion or with glue. Most rock climbing takes place on high strength rock and there has been considerable testing of anchors worldwide. However, there has only been limited testing of anchors in weaker rock. Over 60 anchors were tested in weak rock, failure loads of 8–48 kN were achieved. Chemically bonded anchors were the strongest, the 10 mm rings and 10 mm U-bolts were the only anchors that passed the European standard (EN 959). Older style anchors showed low strength and high variability. The relative strengths of single and twin holes anchors followed predictions based on interaction theory. The results also confirm the prediction of mixed glue/rock failure. The cyclic loading behaviour of anchors was explored, anchor with higher stiffness appeared to perform better; the U-bolts had the best fatigue performance.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Similar content being viewed by others

References

  1. Allen B (2003) The development of the bolt belay Thrutch. Sydney Rock Climbing Club Newslett. April–May 2003

  2. South African Climbing Club testing (2000) A description of anchor testing in soft rock. http://www.climbing.co.za/bolting-information/

  3. Hawkshaw S (2003) Honours thesis. Strength and reliability of chemically bonded rock climbing anchors in sandstone. Sydney University, Sydney

  4. Pircher M (2006) Testing of rock climbing anchors. J Testing Eval, V34, N5 Paper IDJTE14117

  5. Law M, Hawkshaw S (2012) Examination of a rock-climbing fatality caused by equipment failure. Eng Fail Anal 22:21–27

    Article  Google Scholar 

  6. McMillan N (2003) How strong does your climbing gear need to be? British Mountaineering Council technical note 04/03

  7. O’Connor J, Ray A, Franklin B, Stuart B (2001) Changes in the physical and chemical properties of weathered Maroubra sandstone in Sydney AICCM Bull Dec:20–25

  8. Pells PJN (2004) Substance and mass properties for the design of engineering structures in the Hawkesbury sandstone. Austr Geomech V39 N3 September, pp 1–21

  9. BS 5930 (1981) Code of practice for site investigations. British Standards Institution (BSI). London

  10. Hack R, Huisman M (2002) Estimating the intact rock strength of a rock mass by simple means In: van Rooy JL, Jermy CA (eds) engineering geology for developing countries—proceedings of 9th congress of the International Association for Engineering Geology and the Environment, Durban, South Africa, 16–20 September, pp 1971–1977

  11. Schambron T, Uggowitzer P (2009) Effect of wear on static and dynamic failure loads of aluminium-based alloy climbing karabiners. Sports Eng 11(2009):85–91

    Article  Google Scholar 

  12. EN 959:2007 Mountaineering equipment. Rock anchors. Safety requirements and test methods. European Committee for Standardization, Brussels

  13. American Concrete Institute (1989) State-of-the-art report on anchorage to concrete ACI Committee 355, Detroit

  14. Cui S et al (2008) Adhesive bonded anchorage pullout test to estimate in-place concrete compressive strength. J Test Eval V36:N6

    Google Scholar 

  15. Sydney Rockclimbing Club (2011) Full test results for this work. http://routes.sydneyrockies.org.au/display/thelab/Home

  16. Titt Glue-in bolt design has this description and analysis of piton behaviour. http://www.climbargolis.com/Glue-inBoltDesign.htm

  17. Law M (2003) Soft rock bolting guide, Appendix 3. http://www.chockstone.org/TechTips/SoftRockBolting.pdf

  18. Hilti (2014) Product technical guide, spacing information. http://submittals.us.hilti.com/2014PTGVol2/

  19. Sodft rock testing Youtube video (2011) http://www.youtube.com/watch?v=cLW8gBhmE7A

  20. Maddox SJ (1991) Fatigue strength of welded structures, 2nd edn. Abington Publishing, Cambridge

    Google Scholar 

  21. BS 7910-2013 Guide to methods for assessing the acceptability of defects in metallic structures. British Standards Institution (BSI). London

Download references

Author information

Authors and Affiliations

  1. Climbing Anchors Australia, 5/8-10 Industrial Drive, Coffs Harbour, NSW, 2450, Australia

    Michael Law & Steve Hawkshaw

Authors
  1. Michael Law
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Steve Hawkshaw
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Michael Law.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Law, M., Hawkshaw, S. Testing of rock climbing anchors in weak sandstone. Sports Eng 18, 21–28 (2015). https://doi.org/10.1007/s12283-014-0161-3

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12283-014-0161-3

Keywords

Search

Navigation