Abstract
Whiplash injuries are one of the most common injuries reported in automotive rear end collisions. Automobile seat back and head restraints play a role in reducing neck injuries during low speed rear end collisions. Currently, many studies are being conducted on ways to reduce neck injuries. These deal with the design parameters that cause neck injuries and do not address the design of the head restraint connection structure. In this paper, we analyze the various trajectories of the headrest and propose a new design for a connection structure that can move along the corresponding trajectory. We model the headrest connection mechanism as a virtual link using kinematic modeling and perform trajectory analysis. Using the trajectory of motion, we select an oblong shape for the guide slot by fitting it with the equation of an ellipse and propose a new headrest connection mechanism. To evaluate the design of the proposed mechanism, we model the shape of the mechanism and test it using dynamic simulation under collision conditions. In addition, we design a prototype for the proposed guide, conduct a sled test, and confirm that the neck force is reduced by the proposed connection structure. In the proposed structure, the values of maximum upper neck shear and tension decreased by more than 20 % compared to existing headrest.
Article PDF
Similar content being viewed by others
References
Craig, J. J. (2007). Introduction to Robotics Mechanics and Control. Pearson. Upper Saddle River, New Jersey, USA.
Denavit, J. and Hartenberg, R. S. (1955). A kinematic notation for lower pair mechanisms based on matrices. J. Applied Mechanics, 22, 215–221.
Ellis, T., Abbood, A. and Brillault, B. (1992). Ellipse detection and matching with uncertainty. Image and Vision Computing 10, 5, 271–276.
Farmer, C. M. and Wells, J. K. (1999). Relationship of head restraint positioning to driver neck injury in rear-end crashes. Accident Analysis & Prevention 31, 6, 719–728.
Fitzgibbon, A., Pilu, M. and Fisher, R. B. (1999). Direct least square fitting of ellipses. IEEE Trans. Pattern Analysis and Machine Intelligence 21, 5, 476–480.
Gander, W., Golub, G. H. and Strebel, R. (1994). Least square fitting of circles and ellipses. BIT Numerical Mathematics 34, 4, 558–578.
Halif, R. and Flusser, J. (1998). Numerically stable direct least squares fitting of ellipses. Computer Graphics and Visualization 98, 1, 125–132.
Insurance Research Council (2004). Trends in Auto Injury Insurance Claims.
Kim, S. W., Shim, S. J. and Suh, M. W. (2010). Evaluation of reproducibility for neck injury indicators on BioRIDIIg in rear-impact sled test. Spring Conf. Proc., Korean Society of Automotive Engineers, 124–130.
Kim, S. W., Shim, S. J. and Suh, M. W. (2011). Evaluation of the repeatability and reproducibility on BioRIDIIg in rear impact sled test. SAE Paper No. 2011–01-0276.
Kim, S. W., Shim, S. J. and Suh, M. W. (2012). Evaluation of the adequacy of neck injury indicators on BioRIDII in a lower rear impact sled test. Int. J. Automotive Technology 13, 7, 1089–1097.
Korea Insurance Development Institute (2006). Insurance Demand Survey.
Lee, J. W., Yoon, K. H. and Park, G. Y. (2000). A study on occupant neck injury in rear end collision. Trans. Korean Society of Automotive Engineers 8, 3, 130–138.
Matsui, Y., Kubota, M. and Oikawa, S. (2018). Similarity of the measured nic of a BioRID II dummy in car-to-car rear end impact and sled experiments. Int. J. Automotive Technology 19, 1, 77–83.
Park, I. P., Chun, T. B., Kim, G. H. and Lim, J. H. (2005). Study on the methodology to prevent neck injury at low speed rear-end impact. Trans. Korean Society of Automotive Engineers 13, 5, 29–34.
Schmitt, K. U., Muser, M. H., Walz, F. H. and Niederer, P. F. (2002). A proposal for a neck protection criterion for low speed rear-end impacts. Traffic Injury Prevention 3, 2, 117–126.
Shin, M. K., Park, K. J. and Park, G. J. (1999). Occupant analysis and seat design to reduce the neck injury for rear end impact. Trans. Korean Society of Automotive Engineers 7, 9, 182–194.
Smith, M. S., Zuby, D. S. and Lund, A. K. (2005). Improved seat and head restraint evaluations. IIHS, Paper Number. 05–0374.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yang, Y., Kim, Y. & Jeon, E. Design for Headrest Including Guides Slot to Reduce the Neck Force in Rear End Impact. Int.J Automot. Technol. 19, 1041–1048 (2018). https://doi.org/10.1007/s12239-018-0101-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-018-0101-5