Abstract
In this paper, the short carbon fiber (SCF)/PP composite foams with fine open cell were prepared with batch foaming technique using supercritical CO2. The effects of SCF contents, saturation pressure and depressurization rate on the cell morphology were studied. The experimental results indicate that the cell morphology of foamed composites was significantly influenced by the SCF contents and saturation pressure. It is found that the cell size increased and cell density decreased with the increment of SCF contents while the saturation pressure had the opposite effect. However, depressurization rate showed little impacts on the cell morphology due to the presence of SCF.
Similar content being viewed by others
References
O. Faruk, A. K. Bledzki, and L. M. Matuana, Macromol Mater Eng., 192, 113 (2007).
J. L. Hu, Y. Liu, and X. M. Shao, Compos. Part A-Appl. S., 35, 595 (2004).
K. Lozano, J. Bonilla-Rios, and E. V. Barrera, J. Appl. Polym. Sci., 80, 1162 (2001).
S. Kumar, S. Doshi, M. Srinivasarao, J. O. Park, and D. A. Schiraldi, Polymer, 43, 1701 (2002).
W. E. Dondero and R. E. Gorga, J. Polym. Sci. Pol. Phys., 44, 864 (2006).
R. J. Kuriger, M. K. Alam, and D. P. Anderson, Compos. Part A-Appl. S., 33, 53 (2002).
J. Shen, C. Zeng, and L. J. Lee, Polymer, 46, 5218 (2005).
E. Reverchon and S. Cardea, J. Supercrit. Fluid., 40, 144 (2007).
P. Zhang, N. Q. Zhou, and B. Li, Polym-Plast. Technol., 46, 885 (2007).
L. J. M. Jacobs, M. F. Kemmere, and J. T. F. Keurentjes, Green Chem., 10, 731 (2008).
H. X. Huang and J. K. Wang, J. Appl. Polym. Sci., 106, 505 (2007).
K. W. Suh, C. P. Park, M. J. Maurer, M. H. Tusim, R. D. Genova, R. Broos, and D. P. Sophiea, Adv. Mater., 12, 1779 (2000).
D. L. Tomasko, H. Li, D. Liu, and X. Han, Ind. Eng. Chem. Res., 42, 6431 (2003).
D. F. Baldwin, C. B. Park, and N. P. Suh, Polym. Eng. Sci., 38, 674 (1998).
B. Krause, K. Diekmann, N. F. A. Van der Vegt, and M. Wessling, Macromolecules, 35, 1738 (2002).
W. T. Zhai, J. Yu, and J. S. He, Polymer, 49, 2430 (2008).
E. Reverchon and S. Cardea, J. Supercrit. Fluid., 40, 144 (2007).
V. Kumar and H. G. Schirmer, US Patent, 5,684,055 (1997).
G. Verreck, A. Decorte, H. Li, D. Tomasko, A. Arien, J. Peeters, P. Rombaut, G. Van den mooter, and M. E. Brewster, J. Supercrit. Fluid., 38, 383 (2006).
M. Sauceau, C. Nikitine, E. Rodier, and J. Fages, J. Supercrit. Fluid., 43, 367 (2007).
W. Zheng, Y. Lee, and C. B. Park, J. Appl. Polym. Sci., 117, 2972 (2010).
Z. X. Xin, Z. X. Zhang, K. Pal, J. U. Byeon, S. H. Lee, and J. K. Kim, Mater. Des., 31, 589 (2010).
S. Pilla, A. Kramschuster, S. Gong, A. Chandra, and L. Turng, Int. Polym. Proc., 22, 418 (2007).
T. Mori, H. Hayashi, M. Okamoto, S. Yamasaki, and H. Hayami, Compos. Part A-Appl. S., 40, 1708 (2009).
Z. M. Xu, X. L. Jiang, T. Liu, G. H. Hu, L. Zhao, Z. N. Zhu, and W. K. Yuan, J. Supercrit. Fluid., 41, 299 (2007).
Z. X. Zhang, B. X. Lu, Z. X. Xin, and J. K. Kim, Compos. Part B-Eng., 43, 150 (2012).
L. M. Matuana, C. B. Park, and J. J. Balatinecz, Polym. Eng. Sci., 37, 1137 (1997).
S. B. Elvy, G. R. Dennis, and L. Ng, J. Mater. Process Tech., 48, 365 (1995).
A. Ashori, Bioresource Technol., 99, 4661 (2008).
H. Z. Tabari, A. Nourbakhsh, and A. Ashori, Polym. Eng. Sci., 51, 272 (2011).
A. K. Bledzki, O. Faruk, and M. Huque, Polym-Plast. Technol., 41, 435 (2002).
Z. X. Zhang, C. Gao, Z. X. Xin, and J. K. Kim, Compos. Part B-Eng., 43, 2047 (2012).
Y. H. Lee, T. Kuboki, C. B. Park, and M. Sain, AIChE Annual Meeting, Philadephia (PA), pp.16–21, 2008.
H. E. Naguib, C. B. Park, U. Panzer, and N. Reichelt, Polym. Eng. Sci., 42, 1481 (2002).
X. L. Jiang, T. Liu, and L. Zhao, J. Cell Plast, 45, 225 (2009).
P. C. Lee, H. E. Naguib, C. B. Park, and J. Wang, Polym. Eng. Sci., 45, 1445 (2005).
P. C. Lee, J. Wang, and C. B. Park, Ind. Eng. Chem. Res., 45, 175 (2006).
P. C. Lee, G. M. Li, J. W. S. Lee, and C. B. Park, J. Cell Plast, 43, 431 (2007).
W. E. Dondero and R. E. Gorga, J. Polym. Sci. Part B: Polym. Phys., 44, 864 (2006).
E. Amash and P. Zugenmaier, J. Appl. Polym. Sci., 63, 1143 (1997).
M. A. L. Manchado and M. Arroyo, Polymer, 41, 7761 (2000).
C. Yu, Y. Wang, B. Wu, Y. Xie, S. Chen, and W. Li, Polymer Test, 30, 887 (2011).
M. A. L. Manchado, L. Valentini, J. Biagiotti, and J. M. Kenny, Carbon, 43, 1499 (2005).
F. Rezaei, R. Yunus, and N. A. Ibrahim, Mater. Des., 30, 260 (2007).
S. Doroudiani, C. B. Park, and M. T. Kortschot, Polym. Eng. Sci., 36, 2645 (1996).
J. S. Colton and N. P. Suh, World Patent, 8,900,918 (1989).
L. Chen, R. Ozisik, and L. S. Schadler, Polymer, 51, 2368 (2010).
R. W. Sharudin, A. Nabil, K. Taki, and M. Ohshima, J. Appl. Polym. Sci., 119, 1042 (2011).
L. Urbanczyk, C. Calberg, C. Detrenbleur, C. Jerome, and M. Alexandre, Polymer, 51, 3520 (2010).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, C., Ying, S. Batch foaming of short carbon fiber reinforced polypropylene composites. Fibers Polym 14, 815–821 (2013). https://doi.org/10.1007/s12221-013-0815-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12221-013-0815-y