Abstract
The stress and the elastic deflection of internal ring gear in high-speed spur planetary gear units are investigated. A rim thickness parameter is defined as the flexibility of internal ring gear. Six evenly spaced linear springs are used to describe the fitting status between internal ring gear and the gearcase. The finite element model of the whole internal ring gear is established by means of Pro/E and ANSYS. The loads on meshing teeth of internal ring gear are applied according to the contact ratio and the load-sharing coefficient. With the finite element analysis (FEA), the influences of flexibility and fitting status on the stress and elastic deflection of internal ring gear are predicted. The simulation reveals that the principal stress and deflection increase with the decrease of rim thickness of internal ring gear. Moreover, larger spring stiffness helps to reduce the stress and deflection of internal ring gear. Therefore, the flexibility of internal ring gear must be considered during the design of high-speed planetary gear transmissions.
Similar content being viewed by others
References
Kahraman A. Planetary gear train dynamics [J]. ASME Journal of Mechanical Design, 1994, 116: 713–720.
Parker R J, Agashe V, Vijayakar S M. Dynamic response of a planetary gear system using a finite element/contact mechanics model [J]. ASME Journal of Mechanical Design, 2000, 122: 304–310.
Baud S, Velex P. Static and dynamic tooth loading in spur and helical geared systems: Experiments and model validation [J]. ASME Journal of Mechanical Design, 2002, 124: 334–346.
Huang K J, Liu T S. Dynamic analysis of a spur gear by the dynamic stiffness method [J]. ASME Journal of Sound and Vibration, 2000, 234: 311–329.
Brauer J. A general finite element model of involute gears [J]. Finite Elements in Analysis and Design, 2004, 40: 1857–1872.
Zhang J J, Esat I I, Shi Y H. Load analysis with varying mesh stiffness [J]. Computers and Structures, 1999, 70: 273–278.
Kahraman A, Blankenship G W. Effect of involute contact ratio on spur gear dynamics [J]. ASME Journal of Mechanical Design, 1999, 121: 112–118.
Bodas A, Kahraman A. Influence of carrier and gear manufacturing errors on the static load sharing behavior of planetary gear sets [J]. International Journal of JSME, 2004, 47: 908–915.
Hidaka T, Teruaki Y, Nohara M. Dynamic behavior of planetary gear (Part 3): Displacement of ring gear in direction of line of action [J]. Bulletin of the JSME, 1977, 20: 1663–1672.
Chong T H, Kubo A. Simple stress formulas for a thin-rimmed spur gear (Part 3): Examination of the calculation method and stress state of internal spur gear pair [J]. ASME Journal of Mechanisms, Transmissions, and Automation in Design, 1985, 107: 418–423.
Vaujany J P, Kim H C. Effects of rim and web on stresses of internal cylindrical gears [J]. ASME Design Engineering Division, 1996, 88: 73–80.
Oda S, Miyachika K. Root stress of thin-rimmed internal spur gear supported with pins [J]. International Journal of JSME, 1987, 30: 646–652.
Sundararajan S, Blanchette R. Finite element contact analysis of ring gear and support [J]. Canadian Aeronautics and Space Journal, 1986, 32: 148–154.
Kahraman A, Kharazi A A, Umrani M. A deformable body dynamic analysis of planetary gears with thin rims [J]. ASME Journal of Sound and Vibration, 2003, 262: 752–768.
Kahraman A, Vijayakar S. Effect of internal gear flexibility on the quasi-static behavior of a planetary gear set [J]. ASME Journal of Mechanical Design, 2001, 123: 408–415.
Author information
Authors and Affiliations
Corresponding author
Additional information
Supported by Key Project of Ministry of Education of China (No.106050).
GE Nan, born in 1972, female, lecturer.
Rights and permissions
About this article
Cite this article
Ge, N., Zhang, J. Finite element analysis of internal gear in high-speed planetary gear units. Trans. Tianjin Univ. 14, 11–15 (2008). https://doi.org/10.1007/s12209-008-0003-0
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12209-008-0003-0