Advertisement

Springer Nature is making SARS-CoV-2 and COVID-19 research free. View research | View latest news | Sign up for updates

A study on development of the thermal storage type plate heat exchanger including PCM layer

Abstract

Thermal storage type plate heat exchanger (TSPHEs) was newly developed in the process of research a heat pump using industrial waste heat as a heat source for evaporation. A conventional plate heat exchanger is a structure in which two media perform heat transfers through a separation plate. However, TSPHEs have a structure in the basic structure of conventional plate heat exchanger adding the PCM layer filled to phase change material. Therefore, the TSPHEs performed heat exchange between three heat media (hot water-cold water-PCM). The thermal energy supplied through the hot water is mainly transferred to the cold water and some of it is transferred to the phase change material filled in the PCM layer. When if the hot water is shut down and the heat source can’t be supplied, the heat stored in the PCM layer is transferred to the cold water through the hot water, the medium of transmission. In the article, using the ε-NTU method, a thermal equilibrium equation is established between the three heats media used in the TSPHEs. Based on the established theoretical formula, the relationship between total overall heat transfer coefficient and ε, S (temperature differential), and Cr (heat capacity ratio) was obtained. In addition, the validity of the theoretical analysis was demonstrated through the experimental method and compared with the correlation of the existing overall heat transfer coefficient. The results of this article will be utilized as basic data for the design of the TSPHEs, and will be used to predict the amount of heat exchange and thermal storage capacity of the TSPHEs.

This is a preview of subscription content, log in to check access.

References

  1. [1]

    S. Kakac, H. Liu and A. Pramuanjaroenkij, Heat Exchangers: Selection, Rating, and Thermal Design, CRC Press (2002).

  2. [2]

    P. W. Li and C. L. Chan, Thermal Energy Storage Analyses and Designs, Academic Press (2017).

  3. [3]

    S. K. Das and W. Roetzel, Dynamic analysis of plate heat exchangers with dispersion in both fluids, International Journal of Heat and Mass Transfer, 38 (6) (1995) 1127-1140.

  4. [4]

    O. Arsenyeva, J. Tran and E. Y. Kenig, Thermal and hydraulic performance of pillow-plate heat exchangers, Computer Aided Chemical Engineering, 43 (2018) 181–186.

  5. [5]

    J. M. Tran, S. Sommerfeld, M. Piper and E. Y. Kenig, Investigation of pillow-plate condensers for the application in distillation columns, Chemical Engineering Research and Design, 99 (2015) 67–74.

  6. [6]

    M. Piper, C. Wecker, A. Olenberg, J. M. Tran and E. Y. Kenig, An experimental analysis of the topology and dynamics of a falling liquid film over the wavy surface of a vertical pillow plate, Chemical Engineering Science, 130 (2015) 129–134.

  7. [7]

    Y. Zhang, C. Jiang, Z. Yang, Y. Zhang and B. Bai, Numerical study on heat transfer enhancement in capsule-type plate heat exchangers, Applied Thermal Engineering, 108 (2016) 1237–1242.

  8. [8]

    S. W. Hong, O. K. Kwon and J. D. Chung, Application of an embossed plate heat exchanger to adsorption chiller, International Journal of Refrigeration, 65 (2016) 142–153.

  9. [9]

    K. Nilpueng, T. Keawkamrop, H. S. Ahn and S. Wongwises, Effect of chevron angle and surface roughness on thermal performance of single-phase water flow inside a plate heat exchanger, International Communications in Heat and Mass Transfer, 91 (2018) 201–209.

  10. [10]

    C. Gulenoglu, F. Akturk, S. Aradag, N. S. Uzol and S. Kakac, Experimental comparison of performances of three different plates for gasketed plate heat exchangers, International Journal of Thermal Sciences, 75 (2014) 249–256.

  11. [11]

    D. P. Sekulić and R. K. Shah, Thermal design theory of three-fluid heat exchangers, Advances in Heat Transfer, 26 (1995) 219–328.

  12. [12]

    H. Zhang, S. Shao, H. Xu, H. Zou, M. Tang and C. Tian, Numerical investigation on fin-tube three-fluid heat exchanger for hybrid source HVAC&R systems, Applied Thermal Engineering, 95 (2016) 157–164.

  13. [13]

    S. K. Singh, M. Mishra and P. K. Jha, Transient behavior of co-current parallel flow three-fluid heat exchanger, International Communications in Heat and Mass Transfer, 52 (2014) 46–50.

  14. [14]

    T. Mohapatra, B. N. Padhi and S. S. Sahoo, Experimental investigation of convective heat transfer in an inserted coiled tube type three fluid heat exchanger, Applied Thermal Engineering, 117 (2017) 297–307.

  15. [15]

    M. Eslami and M. A. Bahrami, Sensible and latent thermal energy storage with constructal fins, International Journal of Hydrogen Energy, 42 (28) (2017) 17681-17691.

  16. [16]

    H. Tanaka, T. Tomita and M. Okumiya, Feasibility study of a district energy system with seasonal water thermal storage, Solar Energy, 69 (6) (2000) 535-547.

  17. [17]

    S. Boonnasa and P. Namprakai, The chilled water storage analysis for a university building cooling system, Applied Thermal Engineering, 30 (11-12) (2010) 1396–1408.

  18. [18]

    G. Li, Sensible heat thermal storage energy and exergy performance evaluations, Renewable and Sustainable Energy Reviews, 53 (2016) 897–923.

  19. [19]

    A. F. Regin, S. C. Solanki and J. S. Saini, Heat transfer characteristics of thermal energy storage system using PCM capsules: A review, Renewable and Sustainable Energy Reviews, 12 (9) (2018) 2438-2458.

  20. [20]

    F. Agyenim, P. Eames and M. Smyth, A comparison of heat transfer enhancement in a medium temperature thermal energy storage heat exchanger using fins, Solar Energy, 83 (9) (2009) 1509-1520.

  21. [21]

    N. H. S. Tay, M. Belusko and F. Bruno, An effectiveness-NTU technique for characterising tube-in-tank phase change thermal energy storage systems, Applied Energy, 91 (1) (2012) 309-319.

  22. [22]

    H. A. Zondag, R. de Boer, S. F. Smeding and J. van der Kamp, Development of industrial PCM heat storage lab prototype, Energy Procedia, 135 (2017) 115–125.

  23. [23]

    Y. Fang, J. Niu and S. Deng, An analytical technique for the optimal designs of tube-in-tank thermal energy storage systems using PCM, International Journal of Heat and Mass Transfer, 128 (2019) 849–859.

  24. [24]

    M. Medrano, M. O. Yilmaz, M. Nogués, I. Martorell, J. Roca and L. F. Cabeza, Experimental evaluation of commercial heat exchangers for use as PCM thermal storage systems, Applied Energy, 86 (10) (2009) 2047-2055.

  25. [25]

    Y. Liu, J. Duan, X. He and Y. Wang, Experimental investigation on the heat transfer enhancement in a novel latent heat thermal storage equipment, Applied Thermal Engineering, 142 (2018) 361–370.

  26. [26]

    J. Wu, Y. Feng, C. Liu and H. Li, Heat transfer characteristics of an expanded graphite/paraffin PCM-heat exchanger used in an instantaneous heat pump water heater, Applied Thermal Engineering, 142 (2018) 644–655.

  27. [27]

    L. F. Cabeza, H. Mehling, S. Hiebler and F. Ziegler, Heat transfer enhancement in water when used as PCM in thermal energy storage, Applied Thermal Engineering, 22 (10) (2002) 1141-1151.

  28. [28]

    M. Bohlayer and G. Zöttl, Low-grade waste heat integration in distributed energy generation systems-An economic optimization approach, Energy, 159 (2018) 327–343.

  29. [29]

    A. C. Talik, L. S. Fletcher, N. K. Anand and L. W. Swan-son, Heat Transfer and Pressure Drop Characteristics of a Plate Heat Exchanger Using a Propylene-glycol/water Mixture as the Working Fluid (No. CONF-950828—), American Society of Mechanical Engineers, New York, NY (United States) (1995).

  30. [30]

    A. Muley and R. M. Manglik, Experimental investigation of single phase flows in a plate heat exchanger with mixed chevron plates, Journal of Enhanced Heat Transfer, 4 (3) (1997) 187.

Download references

Acknowledgments

This work was supported by Energy Demand Management Core Technology Development Project (10049090, A development of 300 kW high temperature heat pumps for steam supply up to 120 °C for industrial use) funded by the Ministry of Trade, Industry & Energy (MOTIE, Korea). And, thanks for the help given to the experimental process by graduate student Kim, Dong-Hyun. Also, thanks to Samil Industries Co., Ltd., located in Jeonju-si, Jeollabuk-do, Korea for helping to produce prototypes.

Author information

Correspondence to Chaedong Kang.

Additional information

Recommended by Associate Editor Young Soo Chang

Donggyu Lee received B.S. and M.S. degrees in mechanical engineering from Jeonbuk National University in 2006 and 2008. And, he went on to earn doctoral of engineering from the same university in 2015. His research interests are in the areas of refrigeration, HVACs, ice storage systems, geothermal energy system. In recent years, he has been studying heat exchanger that combines thermal storage and heat exchange function using phase change materials.

Chaedong Kang received a B.S. degree in mechanical engineering from Kyung-hee University in 1985 and an M.S. degree in mechanical engineering from KAIST in 1989. He then went on to earn his Dr. Eng. degree from the Tokyo Institute of Technology in 1997. Dr. Kang is currently the Professor of the Department of Mechanical Engineering at Jeonbuk National University in Jeonju, Korea. His research interests are in the areas of refrigeration, building HVACs, ice storage systems, and molecular simulation.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Lee, D., Kang, C. A study on development of the thermal storage type plate heat exchanger including PCM layer. J Mech Sci Technol 33, 6085–6093 (2019). https://doi.org/10.1007/s12206-019-1152-x

Download citation

Keywords

  • Thermal storage type heat exchanger
  • Phase change material (PCM)
  • Three-heat transfer medium
  • Heat storage and release
  • Effective-ness-NTU