Abstract
Fretting damage can be observed in automobile and railway vehicles, fossil and nuclear power plants, and aircrafts. In the present study, the railway axle material RSA1 was used to evaluate fretting fatigue life. Plain and fretting fatigue tests were conducted using a rotary bending fatigue tester with a ring and a bridge-type contact pad. The fretting fatigue limit of a standard specimen was approximately 37% lower than the plain fatigue limit. In the Shinkansen-type specimens, cracks were initiated in the contact area and finally fractured at σamp = 214 MPa. Similarly, cracks were generated early in the rounded areas of all TGV-type specimens and induced fracturing. Tire tracks and rubbed scars were also observed in the oblique crack and fatigue crack growth regions of the fractured surface. Wear debris was detected on the contact surface, and oblique cracks were initiated in the contact area at an early stage. The results of this study can be used to evaluate the structural integrity of railway axles.
Similar content being viewed by others
References
R. B. Waterhouse, Fretting corrosion, Pergamon Press, UK (1975).
P. J. E. Forsyth, Occurrence of fretting fatigue failures in practice, in Fretting Fatigue, Edited by R. B. Waterhouse, Applied Science Publishers LTD, UK (1981).
Y. Mutoh, Fretting wear and fatigue, Kougyousiryousenta, Japan (1997).
Y. Mutoh, Fracture mechanics of fretting fatigue, Journal of the Society Materials Scienc, Japan 46 (11) (1997) 1233–1241.
J. H. Son, S. C. Ahn, J. G. Bae and M. Y. Ha, Fretting damage prediction of connecting rod of marine diesel engine, Journal of Mechanical Science and Technology, 25 (2) (2011) 441–447.
M. Kubota, S. Niho, C. Sakae and Y. Kondo, Effect of understress on fretting fatigue crack initiation of press-fitted axle, JSME Int. J., 46 (3) (2003) 297–302.
K. Hirakawa, K. Toyama and M. Kubota, The analysis and prevention of failure in railway axles, Int. J. of Fatigue, 20 (2) (1998) 135–144.
JSMS Committee on fatigue of materials, Standard evaluation method of fatigue reliability for metallic materials-standard regression method of S-N curves, JSMS-SD-6-04 (2004).
R. Koterazawa, Application of fractography, Nikankougyousinbunsya, Japan (1981).
S. Suresh, Fatigue of materials, Cambridge University Press, UK (1996).
H. Kitagawa and R. Koterazawa, Fractography, Baihukan, Japan (1977).
Author information
Authors and Affiliations
Corresponding author
Additional information
This paper was presented at the FEOFS 2013, Jeju, Korea, June 9–13, 2013. Recommended by Guest Editor Jung-Il Song
Sung Jong Choi is currently employed at the Regional Innovation Center for Automotive Component Test (ACTRIC) of Kyungil University, Korea. He received his Ph.D. in electronic material science from Shizuoka University in Japan (1999). His research interests include the evaluation of fatigue failure and lifespan, fracture surface analysis, and the assessment of machine part durability.
Young Tae Cho is currently employed at the Department of Manufacturing and Design Engineering at Jeonju University, Korea. He received his Ph.D. in electronic material science from Shizuoka University in Japan (1997). His research interests include fracture damage mechanics and design optimization.
Rights and permissions
About this article
Cite this article
Choi, S.J., Cho, Y.T. Fretting fatigue behavior in railway axle materials. J Mech Sci Technol 29, 23–31 (2015). https://doi.org/10.1007/s12206-014-1204-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-014-1204-1