Abstract
Heat transfer inside wall-joint-fins systems is analyzed. The coupled two-dimensional energy equations of the wall and the joint-fin are solved numerically using an iterative high order scheme finite volume method. Advanced fine analytical solution is proposed and various closed form equations for different heat transfer augmentation indicators are obtained. Excellent agreement is noticed between the numerical and the analytical results. Wall-joint-fins systems are more effective in transferring thermal energy when the joint-fin is made of a highly conductive material. Moreover, varying the joint-fin lengths ratio may increase the system effectiveness by a factor of 1.2. In addition, the maximum reported system effectiveness is 925% above that when both wall and joint-fin have same thermal conductivity. The maximum system effectiveness which occurs at specific geometrical aspect factors increases as convective heat transfer coefficients increase. Furthermore, the effectiveness and efficiency of the wall-joint-fins system increase as the relative joint-fins to wall volume ratio increases. The wall-joint-fins efficiency is least affected by the joint-fin lengths ratio. Eventually, the heat transfer coefficient between the joint-fin and the wall is identified. Finally, wall-joint-fin systems are recommended as heat transfer enhancing elements.
Similar content being viewed by others
References
W. J. Rebello, G. R. Peterson and M. Sohal, The impact of heat transfer enhancement techniques on energy savings in the U.S. industry, Proceedings from the 10th Annual Industrial Technology Conference ESL-IE-88-09-27., Huston, TX, USA (1988) 137–144.
A. E. Bergles, R. L. Web and G. H. Junkan, 1979, Energy conservation via heat transfer enhancement, Energy, 4(2) (1979) 193–200.
J. M. Whitham, The effects of retarders in fire tubes of steam boilers, Street Railway Journal, 12(6) (1896) 374.
D. Westphalen, K. Roth and J. Brodrick, Heat transfer enhancement, ASHRAE Journal, 48(4) (2006) 68–71.
D. A. Reay, Heat transfer enhancement-a review of techniques and their possible impact on energy efficiency in the U.K., Heat Recovery Systems & CHP, 11(1) (1991) 1–40.
A. E. Bergles, Handbook of heat transfer, 3rd edition, McGraw-Hill, New York, USA (1998) 11.1–11.76.
R. L. Webb, Air-side heat transfer in finned tube heat exchangers, Heat Transfer Engineering, 1(3) (1980) 33–49.
W. M. Kays and A. L. London, Compact heat exchangers, McGraw-Hill, New York, USA (1984).
R. L. Webb, Principles of enhanced heat transfer, Wiley, New York, USA (1994).
G. Fabbri, Optimum performance of longitudinal convective fins with symmetrical and asymmetrical profiles, International Journal of Heat and Fluid Flow, 20(6) (1999) 634–641.
M. Almogbel and A. Bejan, Cylindrical trees of pin fin, International Journal of Heat and Mass Transfer, 43(23) (2000) 4285–4297.
B. Kundu and P. K. Das, Performance and optimum dimensions of flat fins for tube-and-fin heat exchangers: a generalized analysis, International Journal of Heat and Fluid Flow, 30(4) (2009) 658–668.
M. A. Habib, A. M. Mobarak and A. Z. Aly, Enhanced heat transfer in channels with staggered fins of different spacings, International Journal of Heat and Fluid Flow, 14(2) (1993) 185–190.
A.-R. A. Khaled, Investigation of heat transfer enhancement using permeable fins, Journal of Heat Transfer-Transactions of ASME, 132(3) (2010) (Article no. 034503) 1–5.
R. S. D. Gorla and A. Y. Bakier, Thermal analysis of natural convection and radiation in porous fins, International Communications in Heat and Mass Transfer, 38(5) (2011) 638–645.
S. Kiwan, Effect of radiative losses on the heat transfer from porous fins, International Journal of Thermal Sciences, 46(10) (2007) 1046–1055.
A.-R. A. Khaled, Heat transfer analysis through solar and rooted fins, Journal of Heat Transfer-Transactions of the ASME, 130(7) (2008) (Article no. 74503) 1–4.
A._-R. A. Khaled, Heat transfer enhancements through rooted rectangular-and-Triangular fins, Journal of Enhanced Heat Transfer, 18(2) (2011) 127–136.
A._-R. A. Khaled and I. Al-qadi, Augmentation of heat transfer in wall-rooted-fins systems, International Journal of Numerical Methods for Heat and Fluid Flow, 22(2) (2012) 194–214.
A._-R. A. Khaled, Maximizing heat transfer through joint fin systems, Journal of Heat Transfer-Transactions of The ASME, 128(2) (2006) 203–206.
R._J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, J. V. R. Heberlein, J. H. Davidson, J. Bischof, F. A. Kulacki, U. Kortshagen, S. Garrick and V. Srinivasan, Heat transfer-A review of 2003 literature, International Journal of Heat and Mass Transfer, 49(3) (2006) 451–534.
R._J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, J. V. R. Heberlein, J. H. Davidson, J. Bischof, F. A. Kulacki, U. Kortshagen, S. Garrick, V. Srinivasan, K. Ghosh and R. Mittal, Heat transfer-A review of 2004 literature, International Journal of Heat and Mass Transfer, 53(21–22) (2010) 4343–4396.
R._J. Goldstein, W. E. Ibele, S. V. Patankar, T. W. Simon, T. H. Kuehn, P. J. Strykowski, K. K. Tamma, J. V. R. Heberlein, J. H. Davidson, J. Bischof, F. A. Kulacki, U. Kortshagen, S. Garrick, V. Srinivasan and K. Ghosh, R. Mittal, Heat transfer-A review of 2005 literature, International Journal of Heat and Mass Transfer, 53(21) (2010) 4397–4447.
S. Kakac and H. Liu, Heat exchangers: selection, rating, and thermal design, CRC Press, Boca Raton, Florida, USA (2001).
F. P. Incropera, D. Dewitt, T. L. Bergman and A. S. Lavine, Fundamentals of heat and mass transfer, John Wiley & Sons, Inc. New York. USA. (2006).
M. N. Ozisik, Heat conduction-2nd edition, Wiley, New York, USA (1993) 87–88.
R. LeVeque, Finite volume methods for hyperbolic problems, Cambridge University Press, Cambridge, UK. (2002).
E. F. Toro, Riemann solvers and numerical methods for fluid dynamics, Springer-Verlag. New York, USA (1999).
B. van Leer, Towards the ultimate conservative difference scheme. V. A Second Order Sequel to Godunov’s Method, Journal of Computational Physics, 32(1) (1979) 101–136.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Ji Hwan Jeong
A.-R.A. Khaled is a Professor of Mechanical Engineering at King Abdulaziz University. His current research interests are heat transfer enhancement, enhancement of microsensors detection capability, and thermofluidic system modeling. He received a B.S. degree from the Department of Mechanical Engineering, Kuwait University, in 1995, an M.S. from the Department of Mechanical Engineering, Kuwait University, in 1999, and a Ph.D. from the Department of Mechanical Engineering, The Ohio State University, Columbus, in 2004.
A. Gari is an Assistant Professor in the Mechanical Engineering Department at King Abdulaziz University. His current research interests are in computational heat transfer, and air-conditioning systems. He received a B.S. degree from the Department of Thermal Engineering and Desalination Technology, King Abdulaziz University, in 1994, an M.S. from the Aerospace and Mechanical Engineering Department, Oklahoma State University, Stillwater, in 1999, and a Ph.D. from the Mechanical Engineering Department, University of South Florida, Tampa, in 2006.
Rights and permissions
About this article
Cite this article
Khaled, A.R.A., Gari, A. Analysis of heat transfer inside wall-joint-fins systems. J Mech Sci Technol 27, 2523–2535 (2013). https://doi.org/10.1007/s12206-013-0635-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-013-0635-4