Skip to main content
SpringerLink
Log in

Optimal design of Reinforced Concrete Cantilever Retaining Walls considering the requirement of slope stability

  • Geotechnical Engineering
  • Published:
KSCE Journal of Civil Engineering Aims and scope

An Erratum to this article was published on 03 February 2017

This article has been updated

Abstract

A Reinforced Concrete Cantilever Retaining Wall (RCCRW) is one commonly used soil retaining structure in engineering practice. Various optimization techniques to obtain the optimal design of cantilever walls have been proposed, where the three basic geotechnical constraints of overturning, sliding and bearing failures have generally been taken into consideration. However, none of these approaches have considered the geotechnical requirement of slope stability. In this paper, a novel formulation for the optimal design of RCCRWs that considers the more complete requirements of geotechnical stability of overturning, sliding, bearing and slope failures, is described. The objective function of the minimum cost of materials, geotechnical constraints of wall failures (overturning, sliding and bearing) and the structural requirements for steel reinforcements in the wall sections all followed the conventional approaches used in previous works. Using the Ordinary Method of Slices (OMS) with a circular arc failure surface (CAFS), the factor of safety against slope failure (FS OMS ) for a RCCRW was implicitly derived. Constraints for ensuring that the minimum FS OMS was higher than the required factor were enforced in the formulation. Design variables were the dimensions of the wall sections, corresponding steel reinforcements and the x-y coordinate of center of the CAFS, where the latter are the additional unknowns in this novel formulation. Computational performance of the proposed optimization method is demonstrated and verified through its application to the optimal design of two examples of RCCRWs.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

Change history

  • 03 February 2017

    This erratum is published to notify a spelling error in authors? address. Please take note that changes have been made to authors, Boonchai Ukritchon* and Suraparb *** as below.

References

  • American Concrete Institute, Committee 318 (ACI 318-2005). (2005). Building code requirements for structural concrete and commentary, American Concrete Institute, Farmington Hills, Mich.

  • Bishop, A. W. (1955). “The use of the slip circle in the stability analysis of earth slopes.” Geotechnique, Vol. 5, No. 1, pp. 7–17, DOI: 10.1680/geot.1955.5.1.7.

    Article  Google Scholar 

  • Byrd, R. H., Hribar, M. E., and Nocedal J. (1999). “An interior point algorithm for large-scale nonlinear programming.” SIAM Journal on Optimization, Vol. 9, No. 4, pp. 877–900, DOI: 10.1137/S1052623497325107.

    Article  MATH  MathSciNet  Google Scholar 

  • Camp, C. V. and Akin, A. (2012). “Design of retaining walls using big bang-big crunch optimization.” Journal of Structural Engineering, Vol. 138, No. 3, pp. 438–448, DOI: 10.1061/(ASCE)ST.1943-541X.0000461.

    Article  Google Scholar 

  • Castillo, E., Minguezb, R., Terá nb, A. R., and Fernández-Cantelic, A. (2004). “Design and sensitivity analysis using the probability-safetyfactor method: An Application to Retaining Walls.” Structural Safety, Vol. 26, pp. 159–179, DOI: 10.1016/S0167-4730(03)00039-0.

    Article  Google Scholar 

  • Ceranic, B., Fryer, C., and Baines, R. W. (2001). “Application of simulated annealing to the optimum design of reinforced concrete retaining structures.” Computers and Structures, Vol. 79, pp. 1569–1581, DOI: 10.1016/S0045-7949(01)00037-2.

    Article  Google Scholar 

  • Fellenius, W. (1936). “Calculation of the stability of earth dams.” Transactions of the 2nd congress on large dams, International commission on large dams of the world power conference, Vol. 4, pp. 445–462.

    Google Scholar 

  • Fornberg, B. (1988). “Generation of finite difference formulas on arbitrarily spaced grids.” Mathematics of Computation, Vol. 51, No. 184, pp. 699–706, DOI: 10.1090/S0025-5718-1988-0935077-0.

    Article  MATH  MathSciNet  Google Scholar 

  • Gandomi, A. H., Kashani, A. R., Roke, D. A., and Mousavi, M. (2015). “Optimization of retaining wall design using recent swarm intelligence techniques,” Engineering Structures, Vol. 103, pp. 72–84, DOI: 10.1016/j.engstruct.2015.08.034.

    Article  Google Scholar 

  • Ghasemi, H., Brighenti, R., Zhuang, X., Muthu, J., and Rabczuk, T. (2015). “Optimal fiber content and distribution in fiber-reinforced solids using a reliability and NURBS based sequential optimization approach.” Structural and Multidisciplinary Optimization, Vol. 51, No. 1, pp. 99–112, DOI: 10.1007/s00158-014-1114-y.

    Article  MathSciNet  Google Scholar 

  • Ghasemi, H., Rafiee, R., Zhuang, X., Muthu, J., and Rabczuk, T. (2014). “Uncertainties propagation in metamodel-based probabilistic optimization of CNT/polymer composite structure using stochastic multi-scale modeling.” Computational Materials Science, Vol. 85, pp. 295–305, DOI: 10.1016/j.commatsci.2014.01.020.

    Article  Google Scholar 

  • Ghazavi, M. and Bazzazian Bonab, S. (2011). “Optimization of reinforced concrete retaining walls using ant colony method.” Proc., 3rd Int. Symposium on Geotechnical Safety and Risk (ISGSR), Germany.

    Google Scholar 

  • Kaveh, A. and Abadi, S. M. A. (2011). “Harmony search based algorithms for the optimum cost design of reinforced concrete cantilever retaining walls.” International Journal of Civil Engineering, Vol. 9, No. 1, pp. 1–8.

    Google Scholar 

  • Kaveh, A., Kalateh-Ahani, M., and Fahimi-Farzam, M. (2013). “Constructability optimal design of reinforced concrete retaining walls using a multi-objective genetic algorithm.” Structural Engineering and Mechanics, Vol. 47, No. 2, pp. 227–245, DOI: 10.12989/sem.2013.47.2.227.

    Article  Google Scholar 

  • Khajehzadeh, M., Taha, M. R., El-Shafie, A., and Eslami, M. (2010). “Design of retaining wall using particle swarm optimization with passive congregation.” Australian Journal of Basic and Applied Sciences, Vol. 4, No. 11, pp. 5500–5507.

    Google Scholar 

  • Khajehzadeh, M. and Eslami, M. (2012). “Gravitational search algorithm for optimization of retaining structures.” Indian Journal of Science and Technology, Vol. 5, No. 1, pp. 1821–1827.

    Google Scholar 

  • Khajehzadeh, M., Taha, M. R., and Eslami, M. (2013). “Efficient gravitational search algorithm for optimum design of retaining walls.” Structural Engineering and Mechanics, Vol. 45, No. 1, pp. 111–127, DOI: 10.12989/sem.2013.45.1.111.

    Article  Google Scholar 

  • Mehrotra, S. (1992). “On the implementation of a primal-dual interior point method.” SIAM Journal on Optimization, Vol. 2, No. 4, pp. 575. DOI: 10.1137/0802028.

    Article  MATH  MathSciNet  Google Scholar 

  • NLPSolve (2016). Waterloo Maple Inc. 2016. Maple Help: NLPSolve Available from: http://www.maplesoft.com/support/help/Maple/view. aspx?path=Optimization/NLPSolve

  • Palacios-Gomez, F., Lasdon, L., and Enquist, M. (1982). “Nonlinear optimization by successive linear programming.” Management Science, Vol. 28, No. 10, pp. 1106–1120, DOI: 10.1287/mnsc.28.10.1106.

    Article  MATH  Google Scholar 

  • Pourbaba, M., Talatahari, S., and Sheikholeslami, R. (2013). “A chaotic imperialist competitive algorithm for optimum cost design of cantilever retaining walls.” KSCE Journal of Civil Engineering, Vol. 17, No. 5, pp. 972–979, DOI: 10.1007/s12205-013-0283-3.

    Article  Google Scholar 

  • Rabczuk, T., Zi, G., Bordas, S., and Nguyen-Xuan, H. (2008). “A geometrically non-linear three-dimensional cohesive crack method for reinforced concrete structures.” Engineering Fracture Mechanics, Vol. 75, No. 16, pp. 4740–4758, DOI: 10.1016/j.engfracmech. 2008.06.019.

    Article  Google Scholar 

  • Rabczuk, T. and Belytschko, T. (2006). “Application of particle methods to static fracture of reinforced concrete structures.” International Journal of Fracture, Vol. 137 Nos. 1-4, pp. 19–49, DOI: 10.1007/s10704-005-3075-z.

    Article  MATH  Google Scholar 

  • Rhomberg, E. J. and Street, W. M. (1981). “Optimal design of retaining walls.” Journal of Structural Division, ASCE Vol. 107, No. 5, pp. 992–1002, DOI: 10.4203/ccp.92.26

    Google Scholar 

  • Sadoglu, E. (2014). “Design optimization for symmetrical gravity retaining walls.” Acta Geotechnica Slovenica, Vol. 11, No. 1, pp. 61–73.

    Google Scholar 

  • Saribas, A. and Erbatur, F. (1996). “Optimization and sensitivity of retaining structures.” Journal of Geotechnical Engineering, ASCE, Vol. 122, No. 8, pp. 649–656, DOI: 10.1061/(ASCE)0733-9410 (1996)122:8(649).

    Article  Google Scholar 

  • Sivakumar Babu, G. L. and Basha, B. M. (2008). “Optimum design of cantilever retaining walls using target reliability approach.” International Journal of Geomechanic, ASCE, Vol. 8, pp. 240–252, DOI: 10.1061/(ASCE)1532-3641(2008)8:4(240).

    Article  Google Scholar 

  • Talatahari, S. and Sheikholeslami, R. (2014). “Optimum design of gravity and reinforced retaining walls using enhanced charged system search algorithm.” KSCE Journal of Civil Engineering, Vol. 18, No. 5, pp. 1464–1469, DOI: 10.1007/s12205-014-0406-5.

    Article  Google Scholar 

  • Temür, R. and Bekdas, G. (2016). “Teaching learning-based optimization for design of cantilever retaining walls.” Structural Engineering and Mechanics, Vol. 57, No. 4, pp. 763–783, DOI: 10.12989/sem.2016.57.4.763.

    Article  Google Scholar 

  • Ukritchon, B., Boonyatee, T., and Sinauo, P. (2004). AutoSLOPE (2004): Automated Slope Stability Analysis Program. Department of Civil Engineering, Faculty of Engineering, Chulalongkorn University.

    Google Scholar 

  • Ukritchon, B. and Keawsawasvong, S. (2016). “A practical method for the optimal design of continuous footing using ant-colony optimization.” Acta Geotechnica Slovenica, Vol. 13, No. 2, pp. 45–55.

    Google Scholar 

  • Waterloo Maple Inc. (2016). http://www.maplesoft.com

  • Waltz, R. A. and Plantenga, T. D. (2004). KNITRO 7.0 User’s Manual. Technical report, Ziena Optimization, Inc., Evanston, IL,USA, September 2004.

    Google Scholar 

  • Yepes, V., Alcala, J., Perea, C., and González-Vidosa, F. (2008). “A parametric study of optimum earth-retaining walls by simulated annealing.” Engineering Structures, Vol. 30, No. 3, pp. 821–830, DOI: 10.1016/j.engstruct.2007.05.023.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Geotechnical Research Unit, Dept. of Civil Engineer, Faculty of Engineering, Chulalongkorn University, Bongkok, 10330, Thailand

    Boonchai Ukritchon & Suraparb Keawsawasvong

  2. Technical Engineering, Cana Sino Construction Corporation, Phnom Penh, Cambodia

    Sophea Chea

Authors
  1. Boonchai Ukritchon
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Sophea Chea
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Suraparb Keawsawasvong
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Boonchai Ukritchon.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ukritchon, B., Chea, S. & Keawsawasvong, S. Optimal design of Reinforced Concrete Cantilever Retaining Walls considering the requirement of slope stability. KSCE J Civ Eng 21, 2673–2682 (2017). https://doi.org/10.1007/s12205-017-1627-1

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12205-017-1627-1

Keywords

Search

Navigation