Abstract
This paper reviews the literature concerning the energy savings that can be achieved through optimized building shape and form, improved building envelopes, improved efficiencies of individual energy-using devices, alternative energy using systems in buildings, and through enlightened occupant behavior and operation of building systems. Cost information is also provided. Both new buildings and retrofits are discussed. Energy-relevant characteristics of the building envelope include window-to-wall ratios, insulation levels of the walls and roof, thermal resistance and solar heat gain coefficient of windows, degree of air tightness to prevent unwanted exchange of air between the inside and outside, and presence or absence of operable windows that connect to pathways for passive ventilation. Provision of a high-performance envelope is the single most important factor in the design of low-energy buildings, not only because it reduces the heating and cooling loads that the mechanical system must satisfy but also because it permits alternative (and low-energy) systems for meeting the reduced loads. In many cases, equipment with significantly greater efficiency than is currently used is available. However, the savings available through better and alternative energy-using systems (such as alternative heating, ventilation, cooling, and lighting systems) are generally much larger than the savings that can be achieved by using more efficient devices (such as boilers, fans, chillers, and lamps). Because improved building envelopes and improved building systems reduce the need for mechanical heating and cooling equipment, buildings with dramatically lower energy use (50–75% savings) often entail no greater construction cost than conventional design while yielding significant annual energy-cost savings.
Similar content being viewed by others
Notes
Primary energy in the case of electricity is the energy used by the power plant and is about three times the energy content of the electricity used by the building.
References
Anderson, R., Christensen, C., & Horowitz, S. (2006). Analysis of residential system strategies targeting least-cost solutions leading to net zero energy homes. ASHRAE Transactions, 112(Part 2), 330–341.
Armstrong, P. R., Leeb, S. B., & Norford, L. K. (2006). Control with building mass—Part II, Simulation. ASHRAE Transactions, 112(Part 1), 462–473.
Audenaert, A., De Cleyn, S. H., & Vankerckhove, B. (2008). Economic analysis of passive houses and low-energy houses compared with standard houses. Energy Policy, 36, 47–55.
Badescu, V., & Sicre, B. (2003). Renewable energy for passive house heating Part 1. Building description. Energy and Buildings, 35, 1077–1084.
Baird, G. (2001). The Architectural Expression of Environmental Control Systems p. 264. London: Spon Press.
Balaras, C. A. (2001). Energy retrofit of a neoclassic office building—Social aspects and lessons learned. ASHRAE Transactions, 107(Part 1), 191–197.
Beeler, A. G. (1998). Integrated design team management within the context of environmental systems theory. Proceedings of the 1998 ACEEE Summer Study on Energy Efficiency in Buildings, 10, 19–30 American Council for an Energy Efficient Economy, Washington.
Bell, M., & Lowe, R. (2000). Energy efficient modernisation of housing, a UK case study. Energy and Buildings, 32, 267–280.
Boonstra, C., Thijssen, I., & Vollebregt, R. (1997). Glazed Balconies in Building Renovation p. 16. London: James & James.
Bourassa, N., Haves, P., & Huang, J. (2002). A computer simulation appraisal of non-residential low energy cooling systems in California. Proceedings of the 2002 ACEEE Summer Study on Energy Efficiency in Buildings, 3, 41–53 American Council for an Energy Efficient Economy, Washington.
Çakmanus, I. (2007). Renovation of existing office buildings in regard to energy economy, An example from Ankara, Turkey. Building and Environment, 42, 1348–1357.
Claridge, D. E., Liu, M., Deng, S., Turner, W. D., Haberl, J. S., Lee, S. U., et al. (2001). Cutting heating and cooling use almost in half without capital expenditure in a previously retrofit building. European Council for an Energy Efficient Economy, 2001 Summer Proceedings, 4, 74–85.
Cohen, R., Bordass, W., & Leaman, A. (2007). Evaluations and comparisons of the achieved energy and environmental performance of two library buildings in England and Sweden. ASHRAE Transactions, 113(Part 2), 14–26.
Dascalaki, E., & Santamouris, M. (2002). On the potential of retrofitting scenarios for offices. Building and Environment, 37, 557–567.
de Dear, R. J., & Brager, G. S. (1998). Developing an adaptive model of thermal comfort and preference. ASHRAE Transactions, 104(Part 1A), 145–167.
de Dear, R. J., & Brager, G. S. (2002). Thermal comfort in naturally ventilated buildings, revisions to ASHRAE Standard 55. Energy and Buildings, 34, 549–561.
Demirbilek, F. N., Yalçiner, U. G., Inanici, M. N., Ecevit, A., & Demirbilek, O. S. (2000). Energy conscious dwelling design for Ankara. Building and Environment, 35, 33–40.
Durkin, T. H. (2006). Boiler system efficiency. ASHRAE Journal, 48(7), 51–57.
Eicker, U., Huber, M., Seeberger, P., & Vorschulze, C. (2006). Limits and potentials of office building climatisation with ambient air. Energy and Buildings, 38, 574–581.
Feist, W., Schnieders, J., Dorer, V., & Haas, A. (2005). Re-inventing air heating: Convenient and comfortable within the frame of the Passive House concept. Energy and Buildings, 37, 1186–1203.
Fisher, D., Schmid, F., & Spata, A. J. (1999). Estimating the energy-saving benefit of reduced-flow and/or multi-speed commercial kitchen ventilation systems. ASHRAE Transactions, 105(Part 1), 1138–1151.
Florides, G. A., Tassou, S. A., Kalogirou, S. A., & Wrobel, L. C. (2002). Measures used to lower building energy consumption and their cost effectiveness. Applied Energy, 73, 299–328.
Ford, B., Patel, N., Zaveri, P., & Hewitt, M. (1998). Cooling without air conditioning: The Torrent Research Centre, Ahmedabad, India. Renewable Energy, 15, 177–182.
Fountain, M. E., Arens, E., Xu, T., Bauman, F. S., & Oguru, M. (1999). An investigation of thermal comfort at high humidities. ASHRAE Transactions, 105, 94–103.
Francisco, P. W., Palmiter, L., & Davis, B. (1998). Modeling the thermal distribution efficiency of ducts, comparisons to measured results. Energy and Buildings, 28, 287–297.
Gamble, D., Dean, B., Meisegeier, D., & Hall, J. (2004). Building a path towards zero energy homes with energy efficient upgrades. Proceedings of the 2004 ACEEE Summer Study on Energy Efficiency in Buildings, 1, 95–106 American Council for an Energy Efficient Economy, Washington.
Gauzin-Müller, D. (2002). Sustainable Architecture and Urbanism p. 255. Basel: Birkhäuser.
Genest, F., & Minea, V. (2006). High-performance retail store with integrated HVAC systems. ASHRAE Transactions, 112(Part 2), 342–348.
Grut, L. (2003). Daimler Chrysler Building, Berlin. In B. Edwards (Ed.), Green Buildings Pay (pp. 86–93). London: Spon Press.
Haller, A., Schweizer, E., Braun, P. O., & Voss, K. (1997). Transparent Insulation in Building Renovation p. 16. London: James & James.
Hamada, Y., Nakamura, M., Ochifuji, K., Yokoyama, S., & Nagano, K. (2003). Development of a database of low energy homes around the world and analysis of their trends. Renewable Energy, 28, 321–328.
Harvey, L. D. D. (2006). A Handbook on Low-Energy Buildings and District-Energy Systems p. 701. London: Earthscan.
Harvey, L. D. D. (2007a). Dangerous anthropogenic interference, dangerous climatic change, and harmful climatic change, non-trivial distinctions with significant policy implications. Climatic Change, 82, 1–25.
Harvey, L. D. D. (2007b). Allowable CO2 Concentrations under the United Nations framework convention on climate change as a function of the climate sensitivity PDF. Environmental Research Letters, 2, 014001. doi:10.1088/1748-9326/2/1/014001.
Harvey, L. D. D. (2008). Energy savings by treating buildings as systems. In D. Hafemeister, B. Levi, M.D. Levine, & P. Schwartz (Eds.), Physics of Sustainable Energy, Using Energy Efficiently and Producing it Renewably, American Institute of Physics Conference Series (pp. 67–87). College Park: American Physics Society.
Harvey, L. D. D., & Siddall, M. (2008). Advanced glazing systems and the economics of comfort. Green Building Magazine, Spring 08, 30–35.
Hastings, S. R. (2004). Breaking the. heating barrier’ Learning from the first houses without conventional heating. Energy and Buildings, 36, 373–380.
Hastings, R., & Wall, M. (2007a). Sustainable Solar Housing, Volume 1, Strategies and Solutions p. 292. London: Earthscan.
Hastings, R., & Wall, M. (2007b). Sustainable Solar Housing, Volume2, Exemplary Buildings and Technologies p. 262. London: Earthscan.
Hawkes, D., & Forster, W. (2002). Energy Efficient Buildings, Architecture, Engineering, and Environment p. 240. New York: Norton.
Hepting, C., & Ehret, D. (2005) Centre for Interactive Research on Sustainability: Energy Performance Analysis Report. Available from www.sdri.ubc.ca/cirs.
Hestnes, A. G., & Kofoed, N. U. (1997). OFFICE, Passive Retrofitting of Office Buildings to Improve their Energy Performance and Indoor Environment, Final Report of the Design and Evaluation Subgroup. European Commission Directorate General for Science Research and Development, JOULE Programme, JOR3-CT96-0034.
Hestnes, A. G., & Kofoed, N. U. (2002). Effective retrofitting scenarios for energy efficiency and comfort, results of the design and evaluation activities within the OFFICE project. Building and Environment, 37, 569–574.
Holford, J. M., & Hunt, G. R. (2003). Fundamental atrium design for natural ventilation. Building and Environment, 38, 409–426.
Holton, J. K. (2002). Base loads (lighting, appliances, DHW) and the high performance house. ASHRAE Transactions, 108(Part 1), 232–242.
Howe, M., Holland, D., & Livchak, A. (2003). Displacement ventilation—Smart way to deal with increased heat gains in the telecommunication equipment room. ASHRAE Transactions, 109(Part 1), 323–327.
Hughes, P. J., & Shonder, J. A. (1998). The Evaluation of a 4000-Home geothermal heat pump retrofit at Fort Polk, Louisiana, Final Report, Oak Ridge National Laboratory, ORNL/CON-460.
Humm, O. (2000). Ecology and economy when retrofitting apartment buildings. IEA Heat Pump Centre Newsletter, 15(4), 17–18.
IEA (International Energy Agency) (2004). Oil Crises & Climate Challenges: 30 Years of Energy Use in IEA Countries, International Energy Agency, Paris, 211 pp.
Interface Engineering, (2005). Engineering a Sustainable World, Design Process and Engineering Innovations for the Center for Health and Healing at the Oregan Health and Science University, River Campus. Available through www.interface-engineering.com.
Kats, G., Alevantis, L., Berman, A., Mills, E., & Perlman, J. (2003). The Costs and Financial Benefits of Green Buildings, A Report to California’s Sustainable Building Task Force. Sustainable Building Task Force, 120 pages.
Krapmeier, H., & Drössler, E. (2001). CEPHEUS, Living Comfort Without Heating p. 139. Vienna: Springer.
Larsson, N. (2001). Canadian green building strategies. In The 18th International Conference on Passive and Low Energy Architecture, Brazil, 7–9 November 2001, pp 17–25.
Lee, K. H., & Strand, R. K. (2008). The cooling and heating potential of an earth tube system in buildings. Energy and Buildings, 40, 486–494.
Lemire, N., & Charneux, R. (2005). Energy-efficiency laboratory design. ASHRAE Journal, 47(5), 58–64.
Levermore, G. J. (2000). Building Energy Management Systems, Applications to Low-Energy HVAC and Natural Ventilation Control p. 519. London: Spon.
Levine, M., Ürge-Vorsatz, D., Blok, K., Geng, L., Harvey, D., Lang, S., et al. (2007). Residential and commercial buildings. In B. Metz, O.R. Davidson, P.R. Bosch, R. Dave, & L.A. Meyer (Eds.), Climate Change 2007, Mitigation. Cambridge: Cambridge University Press Contribution of Working Group III to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change.
Lewis, M. (2004). Integrated design for sustainable buildings. Building for the Future, A Supplement to ASHRAE Journals, 46(9), 22–30.
Liu, M., & Claridge, D. E. (1999). Converting dual-duct constant-volume systems to variable-volume systems without retrofitting the terminal boxes. ASHRAE Transactions, 105(Part 1), 66–70.
Liu, M., Claridge, D. E., & Turner, W. D. (2003). Continuous commissioningSM of building energy systems. Journal of Solar Energy Engineering, 125, 275–281.
Long, N., Torcellini, P. A., Pless, S. D., & Judkoff, R. (2006). Evaluation of the low-energy design process and energy performance of the Zion National Park Visitor Center. ASHRAE Transactions, 112(Part 1), 321–340.
McDonell, G. (2003). Displacement ventilation. The Canadian Architect, 48(4), 32–33.
McDougall, T., Nordmeyer, K., & Klaassen, C. J. (2006). Low-energy building case study: IAMU office and training headquarters. ASHRAE Transactions, 112(Part 1), 312–320.
Mendler, S., & Odell, W. (2000). The HOK Guidebook to Sustainable Design p. 412. New York: Wiley.
Mumma, S. A. (2001). Ceiling panel cooling system. ASHRAE Journal, 43(11), 28–32.
Murphy, P. (ed) (2002). Solar Energy Activities in IEA Countries, International Energy Agency, Solar Heating and Cooling Programme, Paris. Available from www.iea-shc.org.
Parker, D. S., Sherwin, J. R., Sonne, J. K., Barkaszi, S. F., Floyd, D. B. & Withers, C. R. (1998). Measured energy savings of a comprehensive retrofit in an existing Florida residence. In Proceedings of the 1998 ACEEE Summer Study on Energy Efficiency in Buildings, 1, 235–251, American Council for an Energy Efficient Economy, Washington.
Parry, M., Canziani, O., Palutikof, J., van der Linden, P., & Hanson, C. (eds.) (2007). Climate Change 2007, Impacts, Adaptation and Vulnerabilty. Cambridge: Cambridge University Press, Contribution of Working Group II to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change.
Parry, M., Palutikof, J., Hanson, C., & Lowe, J. (2008). Squaring up to reality. Nature Reports Climate Change, 2, 68–70.
Petersdorff, C., Boermans, T., Joosen, S., Kalacz, I., Jakubowska, B., Scharte, M., et al. (2005a). Cost-effective Climate Protection in the EU Building Stock, Report established by Ecofys for EURIMA, 68 pages. Available from www.eurima.org.
Petersdorff, C., Boermans, T., Harnisch, J., Stobbe, O., Ullrich, S., & Wortmann, S. (2005b). Cost-effective Climate Protection in the Building Stock of the New EU Members: Beyond the EU Energy Performance of Buildings Directive, Report established by Ecofys for EURIMA, 78 pages. Available from www.eurima.org.
Pless, S. D., Torcellini, P. A., & Petersen, J. E. (2006). Energy performance evaluation of a low-energy academic building. ASHRAE Transactions, 112(Part 1), 295–311.
Poulos, J. (2007). Existing building commissioning. ASHRAE Journal, 49(9), 66–78.
Prasad, D., & Snow, M. (2005). Designing with Solar Power: A Source Book for Building Integrated Photovoltaics (BiPV) p. 256. London: James & James.
Risbey, J. S. (2008). The new climate discourse, Alarmist or alarming. Global Environmental Change, 18, 26–37.
Roth, K. W., Westphalen, D., & Brodrick, J. (2003). Saving energy with building commissioning. ASHRAE Journal, 45(11), 65–66.
Roy, A. N., Mahmood, A. R., Baslev-Olesen, O., Lojuntin, S., Tang, C. K., & Kannan, K. S. (2005). Low energy office building in Putrajaya, Malaysia. Case studies and innovations. In Proceedings of Conference on Sustainable Building South Asia, 11–13 April 2005, Malaysia, pp. 223–230.
Rudd, A., Kerrigan Jr., P., & Ueno, K. (2004). What will it take to reduce total residential source energy use by up to 60%. Proceedings of the 2004 ACEEE Summer Study on Energy Efficiency in Buildings, 1, 293–305 American Council for an Energy Efficient Economy, Washington.
Safarzadeh, H., & Bahadori, M. N. (2005). Passive cooling effects of courtyards. Building and Environment, 40, 89–104.
Schild, P., & Blom, P. (2002). Pilot Study Report: Jaer School, Nesodden Municipality, Norway, International Energy Agency, Energy Conservation in Buildings and Community Systems, Annex 35. Available from hybvent.civil.auc.dk.
Schmidt, D. (2002). The Centre for Sustainable Building (ZUB), A Case Study. presented at Sustainable Buildings 2002, Oslo, Norway, International Initiative for a Sustainable Built Environment (www.iisbe.org).
Schnieders, J., & Hermelink, A. (2006). CEPHEUS results: measurements and occupants’ satisfaction provide evidence for Passive Houses being an option for sustainable building. Energy Policy, 34, 151–171.
Sekhar, S. C., & Phua, K. J. (2003). Integrated retrofitting strategy for enhanced energy efficiency in a tropical building. ASHRAE Transactions, 109(Part 1), 202–214.
Short, C. A., & Lomas, K. J. (2007). Exploiting a hybrid environmental design strategy in a US continental climate. Building Research and Information, 35, 119–143.
Sodec, F. (1999). Economic viability of cooling ceiling systems. Energy and Buildings, 30, 195–201.
Solaini, G., Dall’o’, G., & Scansani, S. (1998). Simultaneous application of different natural cooling technologies to an experimental building. Renewable Energy, 15, 277–282.
Solomon, S. et al. (eds.) (2007). Climate Change 2007, The Physical Science Basis. Cambridge: Cambridge University Press, Contribution of Working Group I to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change.
Steinbock, J., Eijadi, D., & McDougall, T. (2007). Net zero energy building case study, science house. ASHRAE Transactions, 113(Part 1), 26–35.
Stetiu, C., & Feustel, H. E. (1999). Energy and peak power savings potential of radiant cooling systems in US commercial buildings. Energy and Buildings, 30, 127–138.
Taylor, P. B., Mathews, E. H., Kleingeld, M., & Taljaard, G. W. (2000). The effect of ceiling insulation on indoor comfort. Building and Environment, 35, 339–346.
Tenorio, R. (2007). Enabling the hybrid use of air conditioning: A prototype on sustainable housing in tropical regions. Building and Environment, 42, 605–613.
Thanu, N. M., Sawhney, R. L., Khare, R. N., & Buddhi, D. (2001). An experimental study of the thermal performance of an earth-air-pipe system in single pass mode. Solar Energy, 71, 353–364.
Torcellini, P. A., & Crawley, D. B. (2006). Understanding zero-energy buildings. ASHRAE Journal, 48, 62–69.
Torcellini, P. A., Deru, M., Griffith, B., Long, N., Pless, S., Judkoff, R., et al. (2004a). Lessons learned from field evaluation of six high-performance buildings. Proceedings of the 2004 ACEEE Summer Study on Energy Efficiency in Buildings, 3, 325–337 American Council for an Energy Efficient Economy, Washington.
Torcellini, P. A., Judkoff, R., & Crawley, D. B. (2004b). High-performance buildings: Lessons learned. Buildings for the future (supplement). ASHRAE Journal, 46(9), S4–S11.
Turner, C. H., & Tovey, N. K. (2006). Case study on the energy performance of the Zuckerman Institute for Connective Environmental Research (ZICER) building. ASHRAE Transactions, 113(Part 2), 320–329.
Ürge-Vorsatz, D., Novikova, A., Koeppel, S., & Boza-Kiss, B. (2009). Assessment of potentials and costs of carbon dioxide emission mitigation in the buildings sector: insights into the missing elements (in press).
Viridén, K., Ammann, T., Hartmann, P., & Huber, H. (2003). P+D—Projekt Passivhaus im Umbau (in German). Available from www.viriden-partner.ch.
Voss, K. (2000). Solar Renovation Demonstration Projects, Results and Experience p. 24. London: James & James.
Voss, K., Herkel, S., Pfafferott, J., Löhnert, G., & Wagner, A. (2007). Energy efficient office buildings with passive cooling—results and experiences from a research and demonstration programme. Solar Energy, 81, 424–434.
Wagner, A., Herkel, S., Löhnert, G., & Voss, K. (2004). Energy efficiency in commercial buildings, Experiences and results from the German funding program SolarBau’. Presented at EuroSolar 2004, Freiburg, and available from www.solarbau.de.
Walker, C. E., Glicksman, L. R., & Norford, L. K. (2007). Tale of two low-energy designs, Comparison of mechanically and naturally ventilated office buildings in temperature climates. ASHRAE Transactions, 113(Part 1), 36–50.
Withers, C. R., & Cummings, J. B. (1998). Ventilation, humidity, and energy impacts of uncontrolled airflow in a light commercial building. ASHRAE Transactions, 104(Part 2), 733–742.
Xu, P., Huang, J., Jin, R., & Yang, G. (2007). Measured energy performance of a US-China demonstration energy-efficient office building. ASHRAE Transactions, 113(Part 1), 56–64.
Zhen, B., Shanhou, L., & Weifeng, Z. (2005). Energy efficient techniques and simulation of energy consumption for the Shanghai ecological building. In Proceedings 2005 World Sustainable Building Conference, Tokyo, 27–29 September 2005 (SB05Tokyo), pp. 1073–1078.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Harvey, L.D.D. Reducing energy use in the buildings sector: measures, costs, and examples. Energy Efficiency 2, 139–163 (2009). https://doi.org/10.1007/s12053-009-9041-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12053-009-9041-2