Skip to main content
SpringerLink
Log in

Optimization of process parameters for minimizing the temperature field of high-speed milling of titanium alloy thin-walled parts

  • Original Article
  • Published:
International Journal on Interactive Design and Manufacturing (IJIDeM) Aims and scope Submit manuscript

Abstract

The high milling temperature in the high-speed milling process restricts the production efficiency and processing quality of titanium alloy thin-walled parts. Optimizing the processing parameters can control the temperature within a reasonable range, which can improve its production efficiency and processing quality. Therefore, it is imperative to conduct research on milling temperature and multi-objective parameter optimization during the milling process. In this paper, the temperature field model of the workpiece was established using the moving heat source method. The finite element method was used to simulate the temperature field of the workpiece during the milling process. The milling temperature was measured by an infrared thermal imager, and a milling temperature prediction model was set up based on the experimental data. Considering the minimum milling temperature and the maximum material removal rate, the whale optimization algorithm was applied to optimize the processing parameters. The results showed that the maximum error of simulation and experimental results is less than 15%. The milling temperature decreases with the increase of spindle speed and increases with the increase of cutting depth and feed speed. The Pareto solution set obtained by the optimization method can provide a reference for the selection of subsequent milling parameters.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Mruthunjaya, M., Yogesha, K.B.: A review on conventional and thermal assisted machining of titanium based alloy. Mater. Today: Proc. 46, 8466–8472 (2021)

    Google Scholar 

  2. Akhtar, W., Lazoglu, I.: A novel analytical algorithm for prediction of workpiece temperature in end milling. CIRP Ann. 71(1), 57–60 (2022)

    Article  Google Scholar 

  3. Barzegar, Z., Ozlu, E.: Analytical prediction of cutting tool temperature distribution in orthogonal cutting including third deformation zone. J. Manuf. Process. 67, 325–344 (2021)

    Article  Google Scholar 

  4. Jingjie, Z., Xiangfei, M., Jin, D., Guangchun, X., Zhaoqiang, C., Mingdong, Y., et al.: Modelling and prediction of cutting temperature in the machining of H13 hard steel of transient heat conduction. Materials 14(12), 3176 (2021)

    Article  Google Scholar 

  5. Jiang, F., Liu, Z., Wan, Y., Shi, Z.: Analytical modeling and experimental investigation of tool and workpiece temperatures for interrupted cutting 1045 steel by inverse heat conduction method. J. Mater. Process. Technol. 213(6), 887–894 (2013)

    Article  Google Scholar 

  6. Ruihu, Z.: Analytical model of workpiece surface temperature prediction in 4-axis milling process. Int. J. Adv. Manuf. Technol. 111(7–8), 2155 (2020)

    Google Scholar 

  7. Bagavathiappan, S., Lahiri, B.B., Suresh, S., Philip, J., Jayakumar, T.: Online monitoring of cutting tool temperature during micro-end milling using infrared thermography. Insight Non-Destr. Test. Cond. Monit. 57(1), 9–17 (2015)

    Google Scholar 

  8. Lima, H.V., Campidelli, A.F.V., Maia, A.A.T., Abrão, A.M.: Temperature assessment when milling AISI D2 cold work die steel using tool-chip thermocouple, implanted thermocouple and finite element simulation. Appl. Therm. Eng. 143, 532 (2018)

    Article  Google Scholar 

  9. Cheng, Y., Guan, R., Lu, Z., Xu, M., Liu, Y.: A study on the milling temperature and tool wear of difficult-to-machine 508III steel. Proc. Inst. Mech. Eng. Part B. J. Eng. Manuf. 232(14), 2478 (2018)

    Article  Google Scholar 

  10. Li, J., Tao, B., Huang, S., Yin, Z.: Cutting tools embedded with thin film thermocouples vertically to the rake face for temperature measurement. Sens. Actuators: A Phys. 296(C), 392 (2019)

    Article  Google Scholar 

  11. Qin, C., Tao, J., Liu, C.: Stability analysis for milling operations using an Adams-Simpson-based method. Int. J. Adv. Manuf. Technol. 92(1–4), 969–979 (2017)

    Article  Google Scholar 

  12. Qin, C., Tao, J., Liu, C.: A predictor-corrector-based holistic-discretization method for accurate and efficient milling stability analysis. Int. J. Adv. Manuf. Technol. 96(5–8), 2043–2054 (2018)

    Article  Google Scholar 

  13. Singh, R., Dureja, J.S., Dogra, M., Gupta, M.K., Mia, M.: Influence of graphene-enriched nanofluids and textured tool on machining behavior of Ti-6Al-4V alloy. Int. J. Adv. Manuf. Technol. 105(1–4), 1685–1697 (2019)

    Article  Google Scholar 

  14. Singh, R., Dureja, J.S., Dogra, M., Kumar Gupta, M., Jamil, M., Mia, M.: Evaluating the sustainability pillars of energy and environment considering carbon emissions under machining of Ti-3Al-2.5V. Sustain. Energy Technol. Assess. 42, 100806 (2020)

    Google Scholar 

  15. Singh, R., Dureja, J.S., Dogra, M., Gupta, M.K., Mia, M., Song, Q.: Wear behavior of textured tools under graphene-assisted minimum quantity lubrication system in machining Ti-6Al-4V alloy. Tribol. Int. 145, 106183 (2020)

    Article  Google Scholar 

  16. Pereira Guimarães, B.M., da Silva Fernandes, C.M., Amaral de Figueiredo, D., Correia Pereira da Silva, F.S., Macedo Miranda, M.G.: Cutting temperature measurement and prediction in machining processes: comprehensive review and future perspectives. Int. J. Adv. Manuf. Technol. 120(5–6), 2849–2878 (2022)

    Article  Google Scholar 

  17. Elsadek, A.A., Gaafer, A.M., Mohamed, S.S., Mohamed, A.A.: Prediction and optimization of cutting temperature on hard-turning of AISI H13 hot work steel. SN Appl. Sci. 2(4), 1–12 (2020)

    Article  Google Scholar 

  18. Belloufi, A., Abdelkrim, M., Rezgui, I., Arbaoui, M.E., Tebib, A.: Fuzzy inference system for modelling cutting temperature of AISI 1060 Steel in turning operations. IOP Conf. Ser. Mater. Sci. Eng. 400, 042005 (2018)

    Article  Google Scholar 

  19. Savkovic, B., Kovac, P., Dudic, B., Rodic, D., Taric, M., Gregus, M.: Application of an adaptive “neuro-fuzzy” inference system in modeling cutting temperature during hard turning. Appl. Sci. 9(18), 3739 (2019)

    Article  Google Scholar 

  20. Al Hazza, M. H. F., Adesta, E. Y. T., Superianto, M. Y., Riza, M.: In 2012 International Conference on Advanced Computer Science Applications and Technologies (ACSAT), pp. 275–278 (2012)

  21. Saha, S., Zaman, P.B., Tusar, M.I.H., Dhar, N.R.: Multi-objective genetic algorithm (MOGA) based optimization of high-pressure coolant assisted hard turning of 42CrMo4 steel. Int. J. Interact. Des. Manuf. (IJIDeM) 16(3), 1253–1272 (2022)

    Article  Google Scholar 

  22. Khelfaoui, F., Yallese, M.A., Boucherit, S., Ouelaa, N., Belhadi, S., Ben Salem, S.: Assessment of performance parameters in intermittent turning and multi-response optimization of machining conditions using DF, MOORA, VIKOR, and coupled NSGAII-VIKOR methods. Int. J. Adv. Manuf. Technol. 130(11–12), 5665–5691 (2024)

    Article  Google Scholar 

  23. Lee, W.-J., Park, S.-H., Yoon, H.-S.: A coolant supply strategy based on cutting temperature prediction during the 3-axis end-milling of Ti-6Al-4V. J. Manuf. Process. 84, 272–281 (2022)

    Article  Google Scholar 

  24. Tang, S., Liu, P., Wang, R., Niu, Q., Yang, G., Liu, W., et al.: Study on the cutting temperature of the textured tool by 3D FEA simulation. Mech. Eng. Sci. 1(2), 25 (2020)

    Article  Google Scholar 

  25. Kadam, B.J., Mahajan, K.A.: Optimization of cutting temperature in machining of titanium alloy using response surface method, genetic algorithm and Taguchi method. Mater. Today Proc. 47, 6285–6290 (2021)

    Article  Google Scholar 

  26. Zhang, W., Cheng, C., Du, X., Chen, X.: Experiment and simulation of milling temperature field on hardened steel die with sinusoidal surface. Int. J. Interact. Des. Manuf. 12(1), 345 (2018)

    Article  Google Scholar 

  27. Kus, A., Isik, Y., Cakir, M.C., Coskun, S., Ozdemir, K.: Thermocouple and infrared sensor-based measurement of temperature distribution in metal cutting. Sensors (Basel) 15(1), 1274–1291 (2015)

    Article  Google Scholar 

  28. Norouzifard, V., Hamedi, M.: A three-dimensional heat conduction inverse procedure to investigate tool–chip thermal interaction in machining process. Int. J. Adv. Manuf. Technol. 74(9–12), 1637 (2014)

    Article  Google Scholar 

  29. Jiao, L., Wang, X., Qian, Y., Liang, Z., Liu, Z.: Modelling and analysis for the temperature field of the machined surface in the face milling of aluminium alloy. Int. J. Adv. Manuf. Technol. 81(9–12), 1797–1808 (2015)

    Article  Google Scholar 

  30. Bhirud, N.L., Gawande, R.R.: Measurement and prediction of cutting temperatures during dry milling: review and discussions. J. Braz. Soc. Mech. Sci. Eng. 39(12), 5135 (2017)

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, Liaoning Petrochemical University, Fushun, 113001, China

    Jianping Liu, Changfu Liu, Hao Tong & Daohai Wang

Authors
  1. Jianping Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Changfu Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Hao Tong
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Daohai Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Changfu Liu.

Ethics declarations

Conflict of interest

All authors of this work have stated that they have no conflicting interests.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Liu, J., Liu, C., Tong, H. et al. Optimization of process parameters for minimizing the temperature field of high-speed milling of titanium alloy thin-walled parts. Int J Interact Des Manuf (2024). https://doi.org/10.1007/s12008-024-01806-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s12008-024-01806-1

Keywords

Search

Navigation