Abstract
Robocasting and 3D concrete printing are technologies that belong under the umbrella term material extrusion additive manufacturing. These two free-form fabrication methods are used to produce 3D structures/components in materials such as ceramic pastes, thermosets, and concrete. Common for the materials is their viscoplastic behavior during deposition and structural buildup (i.e., increase in yield stress) after deposition. The material’s complex nature makes it a non-trivial task to ensures that printed layers do not deform when depositing additional layers on top. In this article, we numerically investigate the influence of the yield stress buildup of viscoplastic materials on the stability of the bottom layer during multilayer printing. Specifically, we have developed a computational flssssuid dynamics model that applies a scalar approach to alter the yield stress. The novel model provides fundamental knowledge on how to design the material’s rheology, so the bottom layer can withstand both the hydrostatic and extrusion pressure.
Similar content being viewed by others
References
Z. Chen, Z. Li, J. Li, C. Liu, C. Lao, Y. Fu, C. Liu, Y. Li, P. Wang, and Y. He, J. Eur. Ceram. Soc. 39, 661 (2019).
J. Lindahl, A. A. Hassen, S. Romberg, B. Hedger, P. Hedger Jr, M. Walch, T. DeLuca, W. Morrison, P. Kim, A. Roschli, D. Nuttal, J. Czachowski, B. Post, L. Love, and V. Kunc, in United States (Oak Ridge National Lab. (ORNL), Oak Ridge, TN (US)), (2018).
V. Mechtcherine, F.P. Bos, A. Perrot, W.R.L. da Silva, V.N. Nerella, S. Fataei, R.J.M. Wolfs, M. Sonebi, and N. Roussel, Cem. Concr. Res. 132, 106037 (2020).
J. Jiang, and Y. Ma, Micromachines 11, 633 (2020).
T.T. Le, S.A. Austin, S. Lim, R.A. Buswell, R. Law, A.G.F. Gibb, and T. Thorpe, Cem. Concr. Res. 42, 558 (2012).
O.A. Mohamed, S.H. Masood, and J.L. Bhowmik, Addit. Manuf. 18, 164 (2017).
H. Xia, J. Lu, and G. Tryggvason, Comput. Methods Appl. Mech. Eng. 346, 242 (2019).
H. Xia, J. Lu, and G. Tryggvason, Int. J. Heat Mass Transf. 138, 1310 (2019).
M. Jabbari, I. Baran, S. Mohanty, R. Comminal, M.R. Sonne, M.W. Nielsen, J. Spangenberg, and J.H. Hattel, Adv. Mech. Eng. 10, 5 (2018).
R. Comminal, M.P. Serdeczny, D.B. Pedersen, and J. Spangenberg, Addit. Manuf. 29, 100753 (2019).
R. Comminal, M. P. Serdeczny, D. B. Pedersen, and J. Spangenberg, in Proc. Annu. Int. Solid Free. Fabr. Symp. 1855 (2018).
M. P. Serdeczny, R. Comminal, D. B. Pedersen, and J. Spangenberg, in Proc. Annu. Int. Solid Free. Fabr. Symp. 1849 (2018).
M.P. Serdeczny, R. Comminal, D.B. Pedersen, and J. Spangenberg, Addit. Manuf. 28, 419 (2019).
R. Comminal, M.P. Serdeczny, D.B. Pedersen, and J. Spangenberg, Addit. Manuf. 20, 68 (2018).
R. Comminal, M. P. Serdeczny, D. B. Pedersen, and J. Spangenberg, in 18th Int. Conf. Eur. Soc. Precis. Eng. Nanotechnol. Euspen 18, (2018).
M. P. Serdeczny, R. Comminal, D. B. Pedersen, and J. Spangenberg, in 18th Int. Conf. Eur. Soc. Precis. Eng. Nanotechnol. Euspen 18, (2018).
R. Comminal, W.R. Leal da Silva, T.J. Andersen, H. Stang, and J. Spangenberg, Cem. Concr. Res. 138, 106256 (2020).
N. Roussel, J. Spangenberg, J. Wallevik, and R. Wolfs, Cem. Concr. Res. 135, 106075 (2020).
J. Spangenberg, W.R. Leal da Silva, R. Comminal, M.T. Mollah, T.J. Andersen, and H. Stang, RILEM Tech. Lett. 6, 119 (2021).
M.T. Mollah, R. Comminal, M.P. Serdeczny, D.B. Pedersen, and J. Spangenberg, Addit. Manuf. 46, 102193 (2021).
E.J. O’Donovan, R.I. Tanner, and J. Non-Newton, Fluid Mech. 15, 75 (1984).
E. C. Bingham, An Investigation of the Laws of Plastic Flow (US Government Printing Office, 1917).
FLOW-3D, "Solving The World’s Toughest CFD Problems", (FLOW Sci. (n.d.)). https://www.flow3d.com/products/flow-3d/ (accessed May 10, 2020).
C.W. Hirt, and B.D. Nichols, J. Comput. Phys. 39, 201 (1981).
R. Comminal, J. Spangenberg, and J.H. Hattel, J. Comput. Phys. 283, 582 (2015).
Acknowledgements
The authors acknowledge the support from the Danish Council for Independent Research (DFF) | Technology and Production Sciences (FTP) (Contract No. 8022-00042B). Moreover, the authors thank FLOW-3D® for their support regarding licenses.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Mollah, M.T., Comminal, R., Serdeczny, M.P. et al. Numerical Predictions of Bottom Layer Stability in Material Extrusion Additive Manufacturing. JOM 74, 1096–1101 (2022). https://doi.org/10.1007/s11837-021-05035-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11837-021-05035-9