Skip to main content
Log in

The Application of Powder Rheology in Additive Manufacturing

  • Published:
JOM Aims and scope Submit manuscript


Additive manufacturing (AM) is sensitive to powder variability when applying fine layers in a uniform manner. This demands a high degree of consistency and repeatability in the feedstock. Particle size is often used as a critical quality attribute, but this is not sufficient to fully qualify a feedstock. Indeed, it is inadequate to suggest that any parameter from a single test, e.g., Hall flowmeter or Hausner ratio, can comprehensively describe a powder’s characteristics. This article uses four case studies to demonstrate the limitations of single parameter characterization and how the rheological properties of several metal powders used in AM applications are used to establish in-process performance. In the first study, the significantly reduced permeability and increased specific energy of a one batch of powder demonstrate a clear link to poor layer uniformity. The second study investigates the impact of metal powder manufacturing methods and suppliers, and it shows how shear properties alone cannot be relied on to identify properties that influence the process. The effect of additives on the processability of polymer blends used in AM is also evaluated, and the results show that even small quantities can have a significant effect on the permeability and basic flowability energy of feedstocks. The final study demonstrates the how rheological measurements can be used to identify the optimum blend of fresh and used material when reusing metal powders to manufacture components. These case studies illustrate the ability of a modern powder rheometer to detect minor variations in powders that are directly relevant to performance in AM processes in a way that traditional characterization methods cannot.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Subscribe and save

Springer+ Basic
EUR 32.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or Ebook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

Similar content being viewed by others


  1. K. Shahzad, J. Deckers, J.-P. Kruth, and J. Vleugels, J. Mater. Process. Technol. 213, 1484 (2013).

    Article  Google Scholar 

  2. J.P. Kruth, M.C. Leu, and T. Nakagawa, CIRP Ann. 47, 525 (1998).

    Article  Google Scholar 

  3. S.H. Riza, S.H. Masood, and C. Wen, Laser-Assisted Additive Manufacturing for Metallic Biomedical Scaffolds, ed. S. Hashmi (Oxford: Elsevier, 2014), pp. 285–301.

    Google Scholar 

  4. J. Hoerber, J. Glasschroeder, M. Pfeffer, J. Schilp, M. Zaeh, and J. Franke, Proc. CIRP 17, 806 (2014).

    Article  Google Scholar 

  5. S. Mellor, L. Hao, and D. Zhang, Int. J. Prod. Econ. 149, 194 (2014).

    Article  Google Scholar 

  6. B.P. Conner, G.P. Manogharan, A.N. Martof, L.M. Rodomsky, C.M. Rodomsky, D.C. Jordan, and J.W. Limperos, Addit. Manuf. 1–4, 64 (2014).

    Article  Google Scholar 

  7. M.K. Taylor, J. Ginsburg, A. Hickey, and F. Gheyas, AAPS PharmSciTech 1, 20 (2000).

    Article  Google Scholar 

  8. M. Leturia, M. Benali, S. Lagarde, I. Ronga, and K. Saleh, Powder Technol. 253, 406 (2014).

    Article  Google Scholar 

  9. R. Freeman, Powder Technol. 174, 25 (2007).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations


Corresponding author

Correspondence to Jamie Clayton.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Clayton, J., Millington-Smith, D. & Armstrong, B. The Application of Powder Rheology in Additive Manufacturing. JOM 67, 544–548 (2015).

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: