Skip to main content
SpringerLink
Log in

Effects of reinforced nanofluid with nanoparticles on cutting tool wear morphology

纳米颗粒增强纳米流体对刀具磨损形貌的影响

  • Article
  • Published:
Journal of Central South University Aims and scope Submit manuscript

Abstract

Superalloys are grouped as hard-to-cut materials with relatively poor machinability. Tool wear is considered one of the main machinabiliry attributes in machining superalloys. Although numerous works have been reported on factors governing tool life in machining superalloys, no study was found on the effect of nanoparticles stability on nanofluid performance and consequently resulted tool wear morphologies. In the present work, the nanoparticles were reinforced by means of improving the stability of the base fluid. To that accomplished, the surface active agent (surfactant) was added to the base cutting fluid as a reinforcing element. The effects of new lubricant on the tool wear morphology of A286 works parts were assessed.

摘要

高温合金属于硬切削材料, 加工性较差。在高温合金加工, 刀具磨损被认为是切削性能的主要 特征之一。虽然关于高温合金加工过程中影响刀具寿命的因素已有大量报道, 但关于纳米粒子稳定性 对纳米流体性能的影响以及由此导致的刀具磨损形貌的研究尚未见报道。在本工作中, 通过提高基液 的稳定性来增强纳米粒子。在此基础上, 将切削液中加入表面活性剂作为增强剂, 研究新型润滑剂对 A286 工件刀具磨损形貌的影响。

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. THAKUR A, GANGOPADHYAY S. State-of-the-art in surface integrity in machining of nickel-based superalloys [J]. International Journal of Machine Tools & Manufacture, 2016, 100: 25–54.

    Article  Google Scholar 

  2. SARIKAYA M, YILMAZ V, GÜLLÜ A. Analysis of cutting parameters and cooling/lubrication methods for sustainable machining in turning of Haynes 25 superalloy [J]. Journal of Cleaner Production, 2016, 133: 172–181.

    Article  Google Scholar 

  3. ULUTAN D, OZEL T. Machining induced surface integrity in titanium and nickel alloys: A review [J]. International Journal of Machine Tools & Manufacture, 2011, 51: 250–280.

    Article  Google Scholar 

  4. ZHANG S, LI J F, WANG Y W. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions [J]. Journal of Cleaner Production, 2012, 32: 81–87.

    Article  Google Scholar 

  5. TAZEHKANDI A H, PILEHVARIAN F, DAVOODI B. Experimental investigation on removing cutting fluid from turning of Inconel 725 with coated carbide tools [J]. Journal of Cleaner Production, 2014, 80: 271–281.

    Article  Google Scholar 

  6. GUO C B, WEI D B, DI S C. Improving energy utilization efficiency of electrical discharge milling in titanium alloys machining [J]. Journal of Central South University, 2016, 23: 2550–2557.

    Article  Google Scholar 

  7. CHEN H, CHEN K H, XU Y C, PAN C X, YI J Y, ZHU C J. Microstructure, mechanical properties, and milling performance of arc-PVD AlTiN-Cu and AlTiN/AlTiN-Cu coatings [J]. Journal of Central South Uni versify, 2018, 25: 506–515.

    Article  Google Scholar 

  8. ZHANG Y J, DONG G J, ZHOU M. Simulation and experiment analysis on thermal deformation of tool system in single-point diamond turning of aluminum alloy [J]. Journal of Central South University, 2016, 23: 2223–2229.

    Article  Google Scholar 

  9. SHOKRANI A, DHOKIA V, NEWMAN S T. Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids [J]. International Journal of Machine Tools & Manufacture, 2012, 57: 83–101.

    Article  Google Scholar 

  10. CHETAN, BEHER B C, GHOSH A S, RAO P V. Wear behavior of PVD TiN coated carbide inserts during machining of Nimonic 90 and Ti6A14V superalloys under dry and MQL conditions [J]. Ceramics International, 2016, 42: 14873–14885.

    Article  Google Scholar 

  11. DAVOODI B, ESKANDARI B. Tool wear mechanisms and multi-response optimization of tool life and volume of material removed in turning of N-155 iron-nickel-base superalloy using RSM [J]. Measurement, 2015, 68: 286–294.

    Article  Google Scholar 

  12. CHENG Q, REN W D, LIU Z F, CHEN D J, GU P H, Load-induced error identification of hydrostatic turntable and its influence on machining accuracy [J]. Journal of Central South University, 2016, 23: 2558–2569.

    Article  Google Scholar 

  13. CUI W, TANG J Y. New method for calculating face gear tooth surface involving worm wheel installation errors [J]. Journal of Central South University, 2017, 24: 1767–1778.

    Article  Google Scholar 

  14. POLVOROSA R, SUAREZ A, LOPEZ de LACALLE L N, CERRILLO I, WRETLAND A, VEIGA F. Tool wear on nickel alloys with different coolant pressures: Comparison of alloy 718 and Waspaloy [J]. Journal of Manufacturing Processes, 2017, 26: 44–56.

    Article  Google Scholar 

  15. WANG Q B, MA H B, KONG X G, ZHANG Y M, A distributed dynamic mesh model of a helical gear pair with tooth profile errors [J]. Journal of Central South University, 2018, 25:287–303.

    Article  Google Scholar 

  16. FANG Z H, OBIKAWA T. Turning of Inconel 718 using inserts with cooling channels under high pressure jet coolant assistance [J]. Journal of Materials Processing Technology 2017, 247: 19–28.

    Article  Google Scholar 

  17. CANTERO J L, ALVAREZ J D, MIGUELEZ M H, MARIN N C. Analysis of tool wear patterns in finishing turning of Inconel 718 [J]. Wear, 2013, 297: 885–894.

    Article  Google Scholar 

  18. HOIER P H, KLEMENT U, ALAGAN N T, BENO T, WRETLAND A. Flank wear characteristics of WC-Co tools when turning Alloy 718 with high-pressure coolant supply [J]. Journal of Manufacturing Processes, 2017, 30: 116–123.

    Article  Google Scholar 

  19. LIMA F F, SALES W F, COSTA E S, FLÁVIO J da SILVA, MACHADO A R. Wear of ceramic tools when machining Inconel 751 using argon and oxygen as lubri-cooling atmospheres [J]. Ceramics International, 2016, 43: 667–685.

    Google Scholar 

  20. BEHERA C H, ALEMAYEHU H, GHOSH S, RAO P V. A comparative study of recent lubri-coolant strategies for turning of Ni-based superalloy [J]. Journal of Manufacturing Processes, 2017, 30: 541–552.

    Article  Google Scholar 

  21. TAZEHKANDI A H, SHABGARD M, PILEHVARIAN F. Application of liquid nitrogen and spray mode of biodegradable vegetable cutting fluid with compressed air in order to reduce cutting fluid consumption in turning Inconel 740 [J]. Journal of Cleaner Production, 2015, 108: 90–103.

    Article  Google Scholar 

  22. GRZESIK W, NIESLONY P, HABRAT W, SIENIAWSKI J, LASKOWSKI P. Investigation of tool wear in the turning of Inconel 718 superalloy in terms of process performance and productivity enhancement [J]. Tribology International, 2017, 118: 337–346.

    Article  Google Scholar 

  23. ISRAEL M, RYUTARO T, YASUO Y, KATSUHIKO S, KEIJI Y, SYUHEI Y, MITSURU H. Effect of coating layer loss on the wear rate change of coated carbide tools in turning process [J]. Precision Engineering, 2017, 50: 1–7.

    Article  Google Scholar 

  24. CALISKAN H, KUCUKKOSE M. The effect of aCN/TiAIN coating on tool wear, cutting force, surface finish and chip morphology in face milling of Ti6A14V superalloy [J]. International Journal of Refractory Metals and Hard Materials, 2015, 50: 304–312.

    Article  Google Scholar 

  25. MAKI F A, MEARS L. A comprehensive study on the effects of tool wear on surface roughness, dimensional integrity and residual stress in turning IN718 hard-to-machine alloy [J]. Journal of Manufacturing Processes, 2017, 30: 268–280.

    Article  Google Scholar 

  26. KOSEKI S H, INOUE K, MORITO S H, OHBA T, USUKI H. Comparison of TiN-coated tools using CVD and PVD processes during continuous cutting of Ni-based superalloys [J]. Surface & Coatings Technology, 2015, 283: 353–363.

    Article  Google Scholar 

  27. SUGIHARA T, NISHIMOTO Y, ENOMOTO T. Development of a novel cubic boron nitride cutting tool with atextured flank face for high-speed machining of Inconel 718 [J]. Precision Engineering, 2017, 48: 75–82.

    Article  Google Scholar 

  28. FANG Z, OBIKAWA T. Cooling performance of micro-texture at the tool flank face under high pressure jet coolant assistance [J]. Precision Engineering, 2017, 49: 41–51.

    Article  Google Scholar 

  29. CHOI S U S, EASTMAN J A. Enhancing thermal conductivity of fluids with nanoparticles [J]. ASME Fed, 1995, 231: 99–105.

    Google Scholar 

  30. SIDIK N A, SAMION S, GHADERIAN J, YAZID M N. Recent progress on the application of nanofluids in minimum quantity lubrication machining: A review [J]. International Journal of Heat and Mass Transfer, 2017, 108: 79–89.

    Article  Google Scholar 

  31. CHETAN, BEHERA B C, GHOSH S, RAO P V. Application of nanofluids during minimum quantity lubrication: A case study in turning process [J]. Tribiology International, 2016, 101: 234–246.

    Article  Google Scholar 

  32. GUPTA M K, SOOD P K, SHARMA V S. Optimization of machining parameters and cutting fluids during nano-fluid based minimum quantity lubrication turning of titanium alloy by using evolutionary techniques [J]. Journal of Cleaner Production, 2016, 135: 1276–1288.

    Article  Google Scholar 

  33. PADMINI R, VAMSI KRISHNA P, KRISHNA MOHANA RAO G Effectiveness of vegetable oil based nanofluids as potential cutting fluids in turning AISI 1040 steel [J]. Tribology International, 2016, 94: 490–501.

    Article  Google Scholar 

  34. NAJIHA M S, RAHMAN M M, KADIRGAMA K. Performance of water-based TiO2 nanofluid during the minimum quantity lubrication machining of aluminum alloy, AA6061-T6 [J]. Journal of Cleaner Production, 2016, 135: 1623–1636.

    Article  Google Scholar 

  35. LIU Z H, AN Q, XU J, CHEN M, HAN S H. Wear performance of (nc-AlTiN)/(a-Si3N4) coating and (nc-AlCrN)/(a-Si3N4) coating in high speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions [J]. Wear, 2013, 305: 249–259.

    Article  Google Scholar 

  36. SARTORI S, GHIOTTI A, BRUSCHI S. Hybrid lubricating/cooling strategies to reduce the tool wear in finishing turning of difficult-to-cut alloys [J]. Wear, 2017, 376-377: 107–114.

    Article  Google Scholar 

  37. GUO J, BARBER G C, SCHALL D J, ZOU Q, JACOB S B. Tribological properties of ZnO and WS2 nanofluids using different surfactants [J]. Wear, 2017, 382-383: 8–14.

    Article  Google Scholar 

  38. XIA W, ZHAO J, CHENG X, SUN J, WU H, YAN Y, JIAO S, JIANG Z. Study on growth behaviour of oxide scale and its effects on tribological property of nano-TiO2 additive oil-in-water lubricant [J]. Wear, 2017, 376-377: 792–802.

    Article  Google Scholar 

  39. SHARMA K, TIWARI A K, DIXIT A R, SINGH R K, SINGH M. Novel uses of alumina/graphene hybrid nanoparticle additives for improved tribological properties of lubricant in turning operation [J]. Tribology International, 2018, 119: 99–111.

    Article  Google Scholar 

  40. BORDIN A, BRUSCHI S, GHIOTTI A, BARIANI P F. Analysis of tool wear in cryogenic machining of additive manufactured Ti6A14V alloy [J]. Wear, 2015, 328-329: 89–99.

    Article  Google Scholar 

  41. ASLANTAS K, UCUN İ, ÇICEK A. Tool life and wear mechanism of coated and uncoated Al2O3/TiCN mixed ceramic tools in turning hardened alloy steel [J]. Wear, 2012, 274-275: 442–451.

    Article  Google Scholar 

  42. GOMEZ-PARRA A, ALVAREZ-ALCON M, SALGUERO J, BATISTA M, MARCOS M. Analysis of the evolution of the built-up edge and built-up layer formation mechanisms in the dry turning of aeronautical aluminium alloys [J]. Wear, 2013, 302: 1209–1218.

    Article  Google Scholar 

  43. MUSAVI S H, DAVOODI B, NIKNAM S A. Environmental-friendly turning of A286 superalloy [J]. Journal of Manufacturing Processes, 2018, 32: 734–743.

    Article  Google Scholar 

  44. CORREA J G, SCHROETER R B, MACHADO A R. Tool life and wear mechanism analysis of carbide tools used in the machining of martensitic and super martensitic stainless steels [J]. Tribology International, 2017, 105: 102–117.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, Iran University of Science and Technology, Tehran, 16846-13114, Iran

    Seyed Hasan Musavi, Behnam Davoodi & Seyed Ali Niknam

Authors
  1. Seyed Hasan Musavi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Behnam Davoodi
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Seyed Ali Niknam
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Behnam Davoodi.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Musavi, S.H., Davoodi, B. & Niknam, S.A. Effects of reinforced nanofluid with nanoparticles on cutting tool wear morphology. J. Cent. South Univ. 26, 1050–1064 (2019). https://doi.org/10.1007/s11771-019-4070-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11771-019-4070-2

Key words

关键词

Search

Navigation