Skip to main content
SpringerLink
Log in

Simulation and development of an active damper with robust μ-control for a machine tool with a gantry portal

  • Machine Tool
  • Published:
Production Engineering Aims and scope Submit manuscript

Abstract

Machine tools are generally used with process parameters that are as productive as possible yet stable. One way to raise productivity is to increase the process parameters like cutting speed or depth of cut (DOC). However, this approach will lead to process instabilities sooner or later. An increased rotational speed of the spindle will excite higher eigenfrequencies depending on the tools teeth count. In combination with higher cutting forces resulting from a deeper DOC, the process can become instable because of chatter or other oscillations and vibrations of the machine tool. This paper describes the identification of a critical eigenfrequency and corresponding eigenmode. An active damper was then developed to mitigate the negative effect this critical eigenfrequency has including a robust controller which protects the process from instabilities through changing eigenfrequencies caused by changing machine positions. It will also enable increased process parameters for a higher productivity of the machine tool. A simulation environment of the active damping system with a classic control and a robust \(\mu\)-control was developed. The damper was applied to the machine tool and tested.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16

Similar content being viewed by others

References

  1. Altintas Y, Stepan G, Merdol D, Dombovari Z (2008) Chatter stability of milling in frequency and discrete time domain. CIRP J Manuf Sci Technol 1:35–44

    Article  Google Scholar 

  2. Roth M (2009) Einsatz und Beurteilung eines aktiven Strukturdämpfers in einem Bearbeitungszentrum. Dissertation, Darmstadt

  3. Weck M, Schulz A (2003) Adaptiver Reibungsdämpfer. wt Werkstattstech Online 7:535–540

    Google Scholar 

  4. Brecher C, Manoharan D, Klein W (2010) Active compensation for portal machines. Prod Eng Res Dev 4:255–260

    Article  Google Scholar 

  5. Drossel W-G, Wittstock V (2008) Adaptive spindle support for improving machining operations. CIRP Ann Manuf Technol 57:395–398

    Article  Google Scholar 

  6. Denkena B, Gümmer O (2012) Process stabilization with an adaptronic spindle system. Prod Eng Res Dev 6:484–492

    Google Scholar 

  7. Monnin J, Kuster F, Wegener K (2014) Modeling errors influencing active structural methods for chatter mitigation in milling process. Procedia CIRP 14:494–499

    Article  Google Scholar 

  8. Brecher C, Schauerte G, Merz M (2007) Modeling and simulation of adaptronic drilling tool axes as the basis of control design. Prod Eng Res Dev 1:297–301

    Article  Google Scholar 

  9. Bolsunovsky S, Vermel V, Gubanov G, Leontiev A (2013) Reduction of flexible workpiece vibrations with dynamic support realized as tuned mass damper. Procedia CIRP 8:230–234

    Article  Google Scholar 

  10. Law M, Wabner M, Colditz A, Kolouch M, Noack S, Ihlenfeldt S (2015) Active vibration isolation of machine tools using an electro-hydraulic actuator. CIRP J Manuf Sci Technol 10:36–48

    Article  Google Scholar 

  11. Uhlmann E, Eßmann J, Wintering J-H (2012) Design- and control-concept for compliant machine tools based on controller integrated models. CIRP Ann Manuf Technol 61:347–350

    Article  Google Scholar 

  12. van Dijk NJM, van de Wouw N, Doppenberg EJJ, Oosterling HAJ, Nijmeijer H (2012) Robust active chatter control in the high-speed milling process. IEEE Trans Control Syst Technol 20(4):901–917

    Article  Google Scholar 

  13. Chen Z, Zhang H-T, Zhang X, Ding H (2013) Adaptive active chatter control in milling processes. J Dyn Syst Meas Control 136(2):021007-1-7

    Article  Google Scholar 

  14. Jalizi B (2014) Kompensation quasi-statischer und dynamischer Verlagerungen bei kompakten Portalfräsmaschinen. Dissertation, Darmstadt

  15. Isermann R (2005) Mechatronic systems: fundamentals. Springer, Heidelberg

    Google Scholar 

  16. Waibel M (2013) Aktive Zusatzsysteme zur Schwingungsreduktion in Werkzeugmaschinen. Dissertation, Herbert-Utz-Verlag, München

  17. Zhou K, Doyle JC, Glover K (1996) Robust and optimal Control. Prentice Hall, Upper Saddle River

    MATH  Google Scholar 

  18. Crepin P-Y (2003) Untersuchung zur Eignung eines robusten Filterentwurfs zur Inflight-Diagnose eines elektrohydraulischen Aktuators. Dissertation, Darmstadt

  19. Sattler B (2001) Entwurf eines robusten, filterintegrierten Aktuatorreglers zur Erhöhung der Stabilitätsreserve bei der Dmpfung von Strukturschwingungen. Dissertation, Darmstadt

  20. McFarlane DC, Keith G, Glover K (1989) Robust controller design using normalized coprime factor plant description. Springer, Heidelberg

    MATH  Google Scholar 

  21. Doyle JC (1982) Analysis of feedback systems with structured uncertainties. IEE Proc 129:242–250

    Article  MathSciNet  Google Scholar 

  22. Doyle JC (1985) Structured uncertainty in control system design. In: Proceedings of the IEEE conference on decision and control, pp 260–265

Download references

Acknowledgments

The research project (AiF-RP-No. K-F2012426PK0) was supported from the budget of the Federal Ministry of Economic Affairs through the Arbeitsgemeinschaft industrieller Forschungsvereinigungen Projekt GmbH (AiF) (Association of Industrial Research Organisations). We would like to thank all funding organisations.

Author information

Authors and Affiliations

  1. Institute of Production Management, Technology and Machine Tools, Otto-Berndt-Straße 2, 64287, Darmstadt, Germany

    E. Abele, G. Pfeiffer, B. Jalizi & A. Bretz

Authors
  1. E. Abele
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. G. Pfeiffer
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. B. Jalizi
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. Bretz
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to G. Pfeiffer.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Abele, E., Pfeiffer, G., Jalizi, B. et al. Simulation and development of an active damper with robust μ-control for a machine tool with a gantry portal. Prod. Eng. Res. Devel. 10, 519–528 (2016). https://doi.org/10.1007/s11740-016-0691-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11740-016-0691-6

Keywords

Search

Navigation