Skip to main content
SpringerLink
Log in

A Method for Graphical Representation of Severe Resonance Regions

  • Technical Article---Peer-Reviewed
  • Published:
Journal of Failure Analysis and Prevention Aims and scope Submit manuscript

Abstract

The vibrational responses with a relatively high amplitude are due to the interference with the resonant operational range of the rotating machinery. The average operating speeds for engine cold testing pass through several critical regions while ramping from idle to the maximum testing speed. The resonant severity differs from one critical speed to another depending on the sequence of interference and the cyclic triggering of the machine harmonic distortion. A better understanding of the harmonic distortions can be built by creating a detailed Campbell diagram including the excitations generated by the engine and the electrical drive. This paper defines a comprehensive Campbell diagram including the excitations generated by the variable frequency drive and the engine and locates all the possible critical speeds. The critical speeds are used to create an inverted excitations diagram to graphically locate the most destructive resonance region in the range of the operating speed. A novel graphical methodology is described in the current paper inspired by the linear programming simplex representation.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

Similar content being viewed by others

References

  1. K. Gul, D. Adams, Modeling and torsional vibration analysis of an engine cold-test cell for production fault diagnostics, in Proceedings of the ASME 2009 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, pp. 1–10 (2009)

  2. M. Corbo, S. Malanoski, Practical design against torsional vibration, in 21st Annual Meeting of the Vibration Institute, pp. 189–222 (1997)

  3. S. Mohitkar, M. Dhend, Harmonic measurement and analysis of variable frequency drive (VFD) in industry. Int. J. Res. Advent Technol. 2, 303–309 (2014)

    Google Scholar 

  4. R. Tailony, E. Nikolaidis, Driveline backlash identification and torsional defects detection using torque signatures analysis for an IC engine cold test stand. J. Failure Anal. Prev. 17(6), 1226–1233 (2017)

    Article  Google Scholar 

  5. K. Gul, D. Adams, modeling and torsional vibration analysis of engine cold-test stand drivelines, in Proceedings of the ASME 2007 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, pp. 1–10 (2007)

  6. M. Corbo, S. Malanoski, Practical design against torsional vibration, in Proceedings of the Twenty-Fifth Turbomachinery Symposium, pp. 189–222 (1996)

  7. R. Tailony, New modeling approach for engine cold testing driveline torsional vibration analysis with increased accuracy. Am. J. Mech. Eng. 5(4), 156–160 (2017)

    Article  Google Scholar 

  8. F. Kushner, Rotating component modal analysis and resonance avoidance recommendations, in Proceedings of the Thirty-Third Turbomachinery Symposium, pp. 143–162 (2004)

  9. T. Kimpián, F. Augusztinovicz, Torsional modal analysis of single shaft systems by using a novel vibroacoustic model of a permanent magnet synchronous motor using novel broad band torque excitation. Proc. Int. Conf. Noise Vib. Eng. ISMA 2012(4), 67–78 (2012)

    Google Scholar 

  10. S. Tripathi, P. Jain, Study of critical speed and natural frequency with varying diameter and materials of stepped shaft using Campbell diagram by using FEA. Int. J. Sci. Res. Dev. 5(1), 216–224 (2017)

    CAS  Google Scholar 

  11. F. Hiller, G. Lieberman, Introduction to Operations Research (McGrow Hill, New York, 2001), pp. 109–152

    Google Scholar 

  12. A. Kinsler, P. Shirley, Optimizing ray-triangle intersection via automated search, in IEEE Symposium on Interactive Ray Tracing 2006, pp. 33–38 (2006)

Download references

Author information

Authors and Affiliations

  1. Mechanical, Industrial and Manufacturing Engineering, University of Toledo, 2801 W Bancroft St, Toledo, OH, 43606, USA

    Rauf Tailony

Authors
  1. Rauf Tailony
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Rauf Tailony.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Tailony, R. A Method for Graphical Representation of Severe Resonance Regions. J Fail. Anal. and Preven. 20, 958–966 (2020). https://doi.org/10.1007/s11668-020-00899-6

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11668-020-00899-6

Keywords

Search

Navigation