Advertisement

Journal of Failure Analysis and Prevention

, Volume 9, Issue 3, pp 262–269 | Cite as

Analysis of Fracture in High-Temperature Vacuum Tube Furnace

  • A. B. Mahmud Hasan
  • S. M. Guo
  • M. A. Wahab
Technical Article---Peer-Reviewed
  • 230 Downloads

Abstract

High-temperature vacuum tube furnace (HTVTF) is widely used for processing materials, developing new materials, and sintering various types of material under vacuum or gaseous conditions. A growing concern in engineering research communities and industries is that fracture occurs in the alumina tube after the furnace has run for few hours and this lead to a drainage of huge amount of money when the buyers replace the tube every time. To improve furnace tube longevity and performance in extreme temperature conditions, it is critical to determine the phenomena that take place inside the furnace and cylindrical alumina tube wall. In the present work, mathematical models are developed to understand the effect of stress concentration arising from thermal stresses in tube wall and heat-affected-zones (HAZ) of a HTVTF using multiphysics finite element software Comsol (Stockholm, Sweden). The combination of thermal stress with temperature difference determines the fracture region. Different air flow rates have been considered to find the critical thermal stress region inside the vacuum tube. Analysis suggests that lowering air flow rate and inserting a small copper pipe inside the first block to blow hot air on the second heat-affected zone (HAZ-2) will reduce thermal stress generation inside the tube and prevent the eventual fracture of the vacuum tube. It is expected that this study can lead to a better understanding of the complex phenomena of fracture alumina tube during operation of HTVTF.

Keywords

High-temperature vacuum tube furnace Thermal stress Mathematical modeling Heat-affected zone 

Notes

Acknowledgment

Funding for this research was provided by NASA/EPSCoR Grant No. 127404191/4199. The authors greatly acknowledge for the financial support of this work.

References

  1. 1.
    Yamaguchi, I., Sohma, M., Tsukada, K., Kondo, W., Kamiya, K., Mizuta, S., Kumagai, T., Manabe, T.: Preparation of high-Jc Y123 films on CeO2-buffered sapphire substrates by MOD using a low-cost vacuum technique. Phys. C: Superconductivity 445–448(1), 603–607 (2006)CrossRefGoogle Scholar
  2. 2.
    Demirbas, A.: Production of sodium carbonate from soda ash via flash calcination in a drop tube furnace. Chem. Eng. Process. 41(3), 215–221 (2002)CrossRefGoogle Scholar
  3. 3.
    Zhang, B., Wang, Y., Wang, X., Chen, X., Feng, J.: Determination of antimony, arsenic, bismuth, selenium, tellurium and tin by low pressure atomic absorption spectrometry with a quartz tube furnace atomizer and hydride generation with air addition. Talanta 42(8), 1095–1098 (1995)PubMedCrossRefGoogle Scholar
  4. 4.
    DeLuca, S.J., Voorhees, K.J.: A comparison of products from an air atmosphere tube furnace with a vacuum Curie-point pyrolyzer: implications for biodetection. J. Anal. Appl. Pyrolysis 24(3), 211–225 (1993)CrossRefGoogle Scholar
  5. 5.
    Strumpf, H.J., Stillwagon, T.L., Kotchick, D.M., Coombs, M.G.: Advanced industrial ceramic heat pipe recuperators. Heat Recov. Syst. CHP 8(3), 235–246 (1988)CrossRefGoogle Scholar
  6. 6.
    David, R., Nettles, O., Liu, R., Hasan, A.B.M., Guo, S.M., Wahab, M.A.: Metal surface cleaning using electro-plasma process. In: Symposium of Fracture Mechanics of Welded Structures and Surface Coatings and Surface Cleaning Mechanics, First American Academy of Mechanics Conference, New Orleans, LA, June 17–20, 2008Google Scholar
  7. 7.
    Lounamaa, N., Aass, J.U., Kühne, J., Persson, T.: The elimination of the getter effect in the determination of gases in metals by the vacuum fusion method. Anal. Chim. Acta 29, 267–271 (1963)CrossRefGoogle Scholar
  8. 8.
    Pissanetzky, S.: Numerical simulation of the transient temperature distribution inside a close-packed array of cylindrical tubes during heating and cooling under high vacuum. Nucl. Eng. Des. 56(2), 359–368 (1980)CrossRefGoogle Scholar
  9. 9.
    MTI Corporation Inc.: User’s Manual. Richmond, CA (2006)Google Scholar
  10. 10.
    Mochida, A., Kudo, K., Mizutani, Y., Hattori, M., Nakamura, Y.: Transient heat transfer analysis in vacuum furnaces heated by radiant tube burners. Energy Conv. Manage. 38(10–13), 1169–1176 (1997)CrossRefGoogle Scholar
  11. 11.
    Segall, A.E.: Manufacturing defects and the evidence of thermomechanical fatigue in a ceramic vacuum furnace tube. Eng. Fail. Anal. 13(7), 1184–1190 (2006)CrossRefGoogle Scholar
  12. 12.
    Guo, S.M., Hasan, A.B.M.: Proton exchange membrane fuel cell high carbon monoxide tolerance operation using pulsed heating and pressure swing. ASME J. Fuel Cell Sci. Technol. 6(1), 011022 (2009)CrossRefGoogle Scholar
  13. 13.
    Pissanetzky, S., Cingolani, H., Volpi, R., Almagro, J.C.: Numerical simulation of the transient temperature distribution within the cladding material during annealing in a high vacuum furnace. Nucl. Eng. Des. 65(1), 141–150 (1981)CrossRefGoogle Scholar
  14. 14.
    Materials properties data from www.matweb.com

Copyright information

© ASM International 2009

Authors and Affiliations

  • A. B. Mahmud Hasan
    • 1
  • S. M. Guo
    • 1
  • M. A. Wahab
    • 1
  1. 1.Department of Mechanical EngineeringLouisiana State UniversityBaton RougeUSA

Personalised recommendations