Skip to main content
Log in

Failure Analysis of Induction Hardened Automotive Axles

  • Technical Article---Peer-Reviewed
  • Published:
Journal of Failure Analysis and Prevention Aims and scope Submit manuscript

Abstract

Rollover accidents in light trucks and cars involving an axle failure frequently raise the question of whether the axle broke causing the rollover or did the axle break as a result of the rollover. Axles in these vehicles are induction hardened medium carbon steel. Bearings ride directly on the axles. This article provides a fractography/fracture mechanic approach to making the determination of when the axle failed. Full scale tests on axle assemblies and suspensions provided data for fracture toughness in the induction hardened outer case on the axle. These tests also demonstrated that roller bearing indentions on the axle journal, cross pin indentation on the end of the axle, and axle bending can be accounted for by spring energy release following axle failure. Pre-existing cracks in the induction hardened axle are small and are often difficult to see without a microscope. The pre-existing crack morphology was intergranular fracture in the axles studied. An estimate of the force required to cause the axle fracture can be made using the measured crack size, fracture toughness determined from these tests, and linear elastic fracture mechanics. The axle can be reliably said to have failed prior to rollover if the estimated force for failure is equal to or less than forces imposed on the axle during events leading to the rollover.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26

Similar content being viewed by others

References

  1. Fett, G.A.: Characterization of Semi Float Axle Shaft Bending Failures. SAE Tech Paper Series 940732, Feb (1994)

  2. Burrier, H., Jr.: ASM Handbook, Properties and Selection, vol. 1, 10th edn., pp. 381–382. ASM, Metals Park, OH (1990)

  3. Moyer, C.A.: ASM Handbook, Friction, Lubrication and Wear Technology, vol. 18, pp. 726. ASM, Metals Park, OH (1992)

  4. International Handbook Committee: ASM Handbook, Fractography, vol. 12, pp. 270–272. ASM, Metals Park, OH (1992)

  5. Meyers, M.A., Chawla, K.K.: Mechanical Metallurgy Principles and Applications, pp. 487–490. Prentice-Hall, Engelwood Cliffs, NJ (1984)

    Google Scholar 

  6. Spitzig, W.A., Pellisier, G.E., Beachem, C.D., Hill, M., Warke, R.R.: A Fractographic Analysis of the Relationships Between Fracture Toughness and Surface Topography in Ultrahigh – Strength Steels. Electron Fractigraphy, pp 13–32. ASTM STP 436, ASTM, Philadelphia (1968)

  7. Clarke, C.K.: A Fractographic Study of a Low Nickel Steel. Dissertation, Lehigh University, Bethlehem, PA (1973)

  8. Murakami, Y.: Stress Intensity Factors Handbook, vol. I, chap. 9.6. Pergamon Press, Oxford, UK (1986)

  9. Roe, G.J., Bramfitt, B.L.: ASM Handbook, Properties and Selections; Irons, Steels, and High Performance Alloys, vol. I, Notch Toughness of Steels. ASM, Metals Park, OH (1990)

  10. Barsom, J.M., Rolfe, S.T.: Fracture and Fatigue Control in Structures, 2nd edn., chap. 4.7. Prentice-Hall, Englewood Cliffs, NJ (1987)

  11. Löhe, D., Vöhringer, O.: Stability of residual stresses. In: Totten, G., Howes, M., Inoune, T. (eds.) Handbook of Residual Stresses and Deformation of Steel, pp. 60–62. ASM, Metals Park, OH (2002)

    Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to C. Kendall Clarke.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Clarke, C.K., Halimunanda, D. Failure Analysis of Induction Hardened Automotive Axles. J Fail. Anal. and Preven. 8, 386–396 (2008). https://doi.org/10.1007/s11668-008-9148-3

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11668-008-9148-3

Keywords

Navigation