Abstract
The possibility of increasing the corrosion resistance of automotive sheet steel by electrodepositing with Zn-Co alloy coatings was investigated. Process variables during electrodeposition such as current density, electrolyte flow rate, and pH were varied in order to examine their influence on the electroplating process. Cobalt contents varying from 0.2 to 7 wt% were easily obtained. The influence of these process parameters on the characteristics of the coating could be related to the hydroxide suppression mechanism for anomalous codeposition. The structure and the morphology of the coatings were determined using SEM and XRD analysis. Application properties important for coating systems used in the automotive industry, such as friction behavior, adhesion, and corrosion behavior, were investigated on coatings with varying cobalt content. The corrosion resistance of the Zn-Co alloy layers was found to be better than that of pure zinc coatings.
Similar content being viewed by others
References
J.H. Lindsay, Coated Steel Sheet in the Automotive Industry, The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Galvatech ’95), (Chicago, IL, September 1995, p 579–588
T. Asamura, New Zinc-Coated Steels and Their Processing Technologies in Japan, Proceedings of the Fourth International Conf. on Zinc and Zinc Alloy Coated Steel Sheet (Galvatech ’98), (Tokyo), Sept 1998, p 14–21
D. Crotty and R. Griffin, Performance Characteristics of Zinc Alloys, Plat. Surf. Finish., April 1997, p 57–61
B.C. De Cooman, “Coated Sheet Steel: An Overview of the Current Products and their Performance,” Prof. Dr. Ir. J. Dilewijns: Liber Amicorum, 1997, p 287–310
S.A. Watson, “Zinc-Nickel Alloy Electroplated Steel Coil and Other Precoated Coil for Use by the Automotive Industry: A Review of Literature Published 1983 to 1987,” Nickel Development Institute, European Technical Information Center, Alvechurch, Birmingham, England, March 1988
T.J. Natorski, Zinc and Zinc Alloy Plating in the 90s, Met. Finish., March 1992, p 15–17
J. Giridhar and W.J. Van Ooij, “A New NiZn/ZnCo Coated Steel Wire for Tire Cord Applications,” Wire J. Int., Vol 26 (No. 6), 1993, p 30–37
J. Giridhar, W.J. Van Ooij, and M. Cipparone, “Adhesion Behaviour of a New Corrosion-Resistant Steel Tire Cord Coated with NiZn/ZnCo Alloy Layers,” Rubbercon ’93, International Rubber Conference (New Delhi, India), 1993
J. Giridhar and W.J. Van Ooij, Study of Zn-Ni and Zn-Co Alloy Coatings Electrodeposited on Steel Strips, Part I: Alloy Electrodeposition and Adhesion of Coatings to Natural Rubber Compounds, Surf. Coat. Technol., Vol 52, 1992, p 17–30
A. DeBoeck, L. Vanlerberghe, and M. Vanthournout, Quantitative Analysis of Zinc and Zinc Alloy Coatings on Steel, La Revue de Métallurgie—CIT, Oct 1993, p 1277–1282
A. DeBoeck, M. Vanthournout, and J.M. Van der Hoeven, “The Influence of Texture on the Deformation Behaviour of Electrodeposited Zinc Coatings,” IDDRG Conf. Proc., (Lisbon), May 1994, p 55
Ph. Bérubé and G. L’Espérance, “A Quantitative Method of Determining the Degree of Texture of Zinc Electrodeposits,” J. Electrochem. Soc., 1989, Vol 136, p 2314
C. Ortlieb and A. De Boeck, “SIKEL NV—Product and Application,” 1995
Warnecke and W. Müschenborn, Formability Aspects of Galvannealed Steel Sheet, IDDRG Conf. Proc., (Amsterdam), May 1985
Standard Test Method for Strength Properties of Adhesive in Shear by Tension Loading (Metal to Metal), D 1002-72, ASTM, 1983
K. Meseure, C. Xhoffer, B.C. De Cooman, I. Hertveldt, and J. Dilewijns, The Shear Strength of Galvannealed Coatings on IF Steels, Proc. of Intergalva ’97
T. Akayima, H., Fukushima, K. Higashi, M. Karimkhani, and R. Kammel, Electrodeposition Behavior of Zinc-Iron-Group Metal Binary Alloys from Sulfate Baths, International Conf. on Zinc and Zinc Alloy Coated Sheet Steel (Galvatech ’89) (Tokyo), Sept 1989, p 45–50
H. Fukushima, T. Akiyama, M. Yano, T. Ishikawa, and R. Kammel, Electrodeposition Behaviour of Zn-Iron-Group Metal Alloys from Sulfate and Chloride Baths, ISIJ International, Vol 33 (No. 9), 1993, p 1009–1015
H. Fukushima, T. Akiyama, K. Higashi, R. Kammel, and M. Karimkhani, Electrodeposition Behaviour of Binary Zinc Alloys with Iron-Group Metals from Sulfate Baths, Metall. und Technik, Vol 44 (No. 8), 1990, p 754–759
K. De Wit, “Electroplating and Application Properties of Zn-Fe Coatings on Steel,” Ph. D. dissertation, University of Ghent, 1998, p 208 (in Dutch)
M. Arimura, M. Urai, J. Iwaya, and M. Iwai, “Effects of Press-Forming Factors and Flash Plating on Coating Exfoliation of Galvannealed Steel Sheets,” The Use and Manufacture of Zinc and Zinc Alloy Coated Sheet Steel Products into the 21st Century (Galvatech ’95), (Chicago), Sept 1995, p 733
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Mahieu, J., De Wit, K., De Cooman, B.C. et al. The properties of electrodeposited Zn-Co coatings. J. of Materi Eng and Perform 8, 561–570 (1999). https://doi.org/10.1007/s11665-999-0010-x
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/s11665-999-0010-x