Skip to main content
SpringerLink
Log in

Forming Features at Screw Rolling of Austenitic Stainless-Steel Billets

  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

Abstract

Two-high and three-high screw rolling of stainless-steel billets was conducted. Experimental rolling was simulated using DEFORM software. Differences in the way hardness, Cockroft–Latham normalized damage criterion, and rigidity coefficient under stress condition change while two-high and three-high screw rolling were established. Changing of these parameters was investigated in the cross section of the billets at the stationary stage of screw rolling. It was unambiguously shown that, in terms of conducted experiments, there is a tendency for axial fracture while two-high screw rolling, and for ring-shaped fracture while three-high screw rolling. Research has allowed for quantitatively estimating the value of the radius of ring-shaped area for which possible fracture may occur while three-high screw rolling.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6

Similar content being viewed by others

References

  1. B.A. Romantsev, A.V. Goncharuk, N.M. Vavilkin, and S.V. Samusev, Tpyбнoe пpoизвoдcтвo (Pipe Manufacture), Izdatelskiy Dom MISiS, 2011 (in Russian)

  2. M.M. Skripalenko, V.E. Bazhenov, B.A. Romantsev, M.N. Skripalenko, T.B. Huy, and Yu.A. Gladkov, Mannesmann Piercing of Ingots by Plugs of Different Shapes, Mater. Sci. Technol., 2016, 32, p 1712–1720

    Article  CAS  Google Scholar 

  3. V.A. Parfenov, A.E. Shelest, YuD Khesuani, V.S. Yusupov, and M.V. Chepurin, Piercing of Continuous-Cast Billet on Two-Roller Screw Mills with Liners, Steel Transl., 2019, 49, p 194–197

    Article  Google Scholar 

  4. Z. Zhang, D. Liu, Y. Yang, J. Wang, Y. Zheng, and F. Zhang, Microstructure Evolution of Nickel-Based Superalloy with Periodic Thermal Parameters During Rotary Tube Piercing Process, Int. J. Adv. Manuf. Technol., 2019, 104, p 3991–4006

    Article  Google Scholar 

  5. Z. Pater and J. Kazanecki, Complex Numerical Analysis of the Tube Forming Process Using Diescher Mill, Arch. Metall. Mater., 2013, 58, p 717–724

    Article  CAS  Google Scholar 

  6. A. Naizabekov, A. Arbuz, S. Lezhnev, and E. Panin, The Development and Testing of a New Method of Qualitative Analysis of the Microstructure Quality, For Example of Steel AISI, 321 Subjected to Radial Shear Rolling, Phys. Scr., 2019, 94, p 1–13

    Article  Google Scholar 

  7. L.S. Derevyagina, A.I. Gordienko, and P.O. Kashiro, The Influence of Regimes of Thermomechanical Treatment on the Structural-Phase State, Mechanical Properties, and Fracture Toughness of Low-Alloy Steel API, 5L Grade X52, Russ. Phys. J.+, 2019, 61, p 1971–1977

    Article  CAS  Google Scholar 

  8. D.A. Negodin, S.P. Galkin, E.A. Kharitonov, B.V. Karpov, D.N. Khar’kovskii, I.A. Dubovitskaya, and P.V. Patrin, Testing of the Technology of Radial-Shear Rolling and Predesigning Selection of Rolling Minimills for the Adaptable Production of Titanium Rods with Small Cross Sections Under the Conditions of the “CHMP” JSC, Metallurgist+, 2019, 62(11–12), p 1133–1143

    Article  CAS  Google Scholar 

  9. N.A. Belov, N.O. Korotkova, T.K. Akopyan, and A.M. Pesin, Phase Composition and Mechanical Properties of Al-1.5%Cu-1.5%Mn-0.35%Zr(Fe,Si) Wire Alloy, J. Alloys Compd., 2019, 782, p 735–746

    Article  CAS  Google Scholar 

  10. X. Ding, Y. Shuang, Q. Liu, and C. Zhao, New Rotary Piercing Process for an AZ31 Magnesium Alloy Seamless Tube, Mater. Sci. Technol., 2017, 34(4), p 408–418

    Article  Google Scholar 

  11. S.P. Galkin, Theory and Technology of Stationary Screw Rolling of Billets and Rods Made of Low-Ductility Steels and Alloys. Dissertation, Moscow Institute of Steel and Alloys, Moscow, 1998 (in Russian)

  12. S. Dobatkin, S. Galkin, Y. Estrin, V. Serebryany, M. Diez, N. Martynenko, E. Lukyanova, and V. Perezhogin, Grain Refinement, Texture, and Mechanical Properties of a Magnesium Alloy After Radial-Shear Rolling, J. Alloys Compd., 2019, 774, p 969–979

    Article  CAS  Google Scholar 

  13. A. Stefanik, P. Szota, S. Mróz, T. Bajor, and H. Dyja, Properties of the AZ31 Magnesium Alloy Round Bars Obtained in Different Rolling, Arch. Metall. Mater., 2015, 60(4), p 3001–3006

    Article  CAS  Google Scholar 

  14. I.V. Ratochka, I.P. Mishin, O.N. Lykova, E.V. Naydenkin, and N.V. Varlamova, Structural Evolution and Mechanical Properties of a VT22 Titanium Alloy Under High-Temperature Deformation, Russ. Phys. J.+, 2016, 59(3), p 397–402

    Article  CAS  Google Scholar 

  15. Z. Pater, J. Bartnicki, and J. Kazanecki, 3D Finite Element Method (FEM) Analysis of Basic Process Parameters in Rotary Piercing Mill, Metalurgija, 2012, 51(4), p 501–504

    Google Scholar 

  16. Z. Pater, Ł. Wójcik, and P. Walczuk, Comparative Analysis of Tube Piercing Processes in the Two-Roll and Three-Roll Mills, Adv. Sci. Technol. Res. J., 2019, 13(1), p 37–45

    Article  Google Scholar 

  17. M.N. Skripalenko, B.A. Romantsev, S.P. Galkin, M.N. Skripalenko, L.M. Kaputkina, and T.B. Huy, Prediction of the Fracture of Metal in the Process of Screw Rolling in a Two-Roll Mill, Metallurgist+, 2018, 61(11–12), p 925–933

    Article  CAS  Google Scholar 

  18. M.M. Skripalenko, S.P. Galkin, H.J. Sung, B.A. Romantsev, T.B. Huy, L.M. Kaputkina, M.N. Skripalenko, and A.A. Sidorow, Prediction of Potential Fracturing During Radial-Shear Rolling of Continuously Cast Copper Billets by Means of Computer Simulation, Metallurgist+, 2019, 62(9–10), p 849–856

    Article  CAS  Google Scholar 

  19. M.M. Skripalenko, B.A. Romantsev, L.M. Kaputkina, S.P. Galkin, M.N. Skripalenko, and V.V. Cheverikin, Study of Transient and Steady-State Stages During Two-High and Three-High Screw Rolling of a 12Kh18N10T Steel Workpiece, Metallurgist+, 2019, 63(3–4), p 366–375

    Article  CAS  Google Scholar 

  20. M.A. Shaposhnikov, Mexaничecкиe иcпытaния мeтaллoв (Mechanical testing of metals), Moscow-Leningrad: Gosudarstvennoe nauchno-tehnicheskoe izdatelstvo mashinostroitelnoy literature, 1951 (in Russian)

  21. D. McLean, Mechanical Properties of Metals, 1st ed., Wiley, Hoboken, 1962

    Google Scholar 

  22. A.N. Nikulin, Bинтoвaя пpoкaткa. Haпpяжeния и дeфopмaции (Screw Rolling. Stresses and Strains), Metallurgizdat, 2015 (in Russian)

  23. S. Fanini, Modelling of the Mannesmann Effect in Tube Piercing. Ph.D. Thesis, University of Padua, 2008

  24. Y. Lou, H. Huh, S. Lim, and K. Pack, New Ductile Fracture Criterion for Prediction of Fracture Forming Limit Diagrams of Sheet Metals, Int. J. Solids Struct., 2012, 49, p 3605–3615

    Article  CAS  Google Scholar 

  25. A.V. Vlasov, S.A. Stebunov, S.A. Evsiukov, N.V. Biba, and A.A. Shitikov, Кoнeчнo-элeмeнтнoe мoдeлиpoвaниe тexнoлoгичecкиx пpoцeccoв кoвки и oбъёмнoй штaмпoвки (Finite Element Method Computer Simulation of Technological Processes of Forging and Die Forging), Izdatelstvo MGTU Imeni N.E. Baumana, 2019 (in Russian)

  26. Y. Bai and T. Wierzbicki, A New Model of Metal Plasticity and Fracture with Pressure and Lode Dependence, Int. J. Plast., 2008, 24, p 1071–1096

    Article  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metal Forming, National University of Science and Technology “MISiS”, Leninskiy pr. 4, Moscow, Russia, 119049

    M. M. Skripalenko, B. A. Romantsev, S. P. Galkin, L. M. Kaputkina, M. N. Skripalenko & A. V. Danilin

  2. Department of Physical Metallurgy and Physics of Strength, National University of Science and Technology “MISiS”, Leninskiy pr. 4, Moscow, Russia, 119049

    S. O. Rogachev

Authors
  1. M. M. Skripalenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. B. A. Romantsev
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. P. Galkin
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. L. M. Kaputkina
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. M. N. Skripalenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. A. V. Danilin
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. S. O. Rogachev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to M. M. Skripalenko.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Skripalenko, M.M., Romantsev, B.A., Galkin, S.P. et al. Forming Features at Screw Rolling of Austenitic Stainless-Steel Billets. J. of Materi Eng and Perform 29, 3889–3894 (2020). https://doi.org/10.1007/s11665-020-04831-9

Download citation

  • Received:

  • Revised:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11665-020-04831-9

Keywords

Search

Navigation