Effect of Heat Treatment on the Properties of CoCrMo Alloy Manufactured by Selective Laser Melting
To obtain medical implants with better mechanical properties, it is necessary to conduct studies on the heat treatment process of the selective laser melting (SLM) manufacturing parts. The differential scanning calorimetry method was used to study the heat treatment process of the phase transition of SLM CoCrMo alloy parts. The tensile properties were tested with a tensile test machine, the quantity of carbide precipitated after heat treatment was measured by energy-dispersive x-ray spectroscopy, and the tensile fracture morphology of the parts was investigated using SEM. The obtained results were: Mechanical properties in terms of elongation and tensile strength of CoCrMo alloy manufactured by SLM that had been heat-treated at 1200 °C for 2 h followed by cooling with water were not only higher than the national standard but also higher than the experimental results of the same batch of castings. The mechanism of fracture of parts manufactured by SLM without heat treatment was brittle fracture, whereas parts which had been heat-treated at 1200 °C for 2 h combined with water cooling and at 1200 °C for 1 h with furnace cooling suffered ductile fracture. This study provides the basis for defining the applications for which CoCrMo alloys manufactured by SLM are suitable within the field of medical implants.
KeywordsCoCrMo alloy fracture mechanism microstructure selective laser melting tensile strength
The study was funded by the Henan Provincial Science and Technology Project (182102310072) and the Start-up Funds for High Level Talents of Zhoukou Normal University (No. ZKNUC72019). Also, this work was supported by Analytical and Testing Center of ZKNUC for carrying out SEM and EDS analysis.
- 1.S.U. Hai-Jun, K.C. Wei, G. Wei et al., New Development of Laser Rapid Forming and Its Application in High Performance Materials Processing, Chin. J. Nonferr. Met., 2013, 23(6), p 1567–1574Google Scholar
- 2.T.T. Sun, Y.Q. Yang, S.U. Xu-Bin et al., Research of Densification of 316L Stainless Steel Powder in Selective Laser Melting Process, Laser Technol., 2010, 34(4), p 443–446Google Scholar
- 4.W. Huang, L. Xiaowei, and X. Lin, Research Progress and Developing Trends on Laser Fabrication of Biomedical Materials, Mater. China, 2011, 30(4), p 1–10Google Scholar
- 5.S.U. Xu-Bin, Y.Q. Yang, Y.U. Peng, and J.F. Sun, Development of Porous Medical Implant Scaffolds Via Laser Additive Manufacturing, Trans. Nonferr. Met. Soc. China, 2012, 22(10), p 181–187Google Scholar
- 6.S. Shi, J. Lin, B. Zhou, and X. Wang, Microstructure and Corrosion Resistance of Medical Cobalt-Based Alloys, Rare Metal Mater. Eng., 2007, 36(1), p 37–41Google Scholar
- 7.Journal Academic Department, Application Status and Development Trend of Medical Metal Materials Related Products, J. Clin. Rehabil. Tissue Eng. Res., 2010, 14(51), p 9621–9624Google Scholar
- 8.J. Liu, Development and Application of Biomedical Metal Materials, Metallic Funct. Mater., 2007, 14(6), p 3–40Google Scholar
- 9.Y.-L. Huang, Effect of Heat Treatment on Properties of Cast CoCrMo Alloy, Shanghai Gangyan, 2003, 4, p 27–31Google Scholar
- 13.S.H. Lee, E. Takahashi, and N. Nomura, Effect of Heat Treatment on Microstructure and Mechanical Properties of Ni and C-Free Co-Cr-Mo Alloys for Medical Applications, J. Jpn. Inst. Met., 2005, 46(8), p 1790–1793Google Scholar