Advertisement

Journal of Materials Engineering and Performance

, Volume 27, Issue 4, pp 1936–1944 | Cite as

Investigation of Mild Steel Thin-Wall Tubes in Unfilled and Foam-Filled Triangle, Square, and Hexagonal Cross Sections Under Compression Load

  • Dipen Kumar Rajak
  • L. A. Kumaraswamidhas
  • S. Das
Article
  • 84 Downloads

Abstract

This study has examined proposed structures with mild steel-reinforced LM30 aluminum (Al) alloy having diversely unfilled and 10 wt.% SiCp composite foam-filled tubes for improving axial compression performance. This class of material has novel physical, mechanical, and electrical properties along with low density. In the present experiment, Al alloy foams were prepared by the melt route technique using metal hydride powder as a foaming agent. Crash energy phenomena for diverse unfilled and foam-filled in mild steel thin-wall tubes (triangular, square and hexagonal) were studied as well. Compression deformation investigation was conducted at strain rates of 0.001-0.1/s for evaluating specific energy absorption (SEA) under axial loading conditions. The results were examined to measure plateau stress, maximum densification strain, and deformation mechanism of the materials. Specific energy absorption and total energy absorption capacities of the unfilled and filled sections were determined from the compressive stress–strain curves, which were then compared with each other.

Keywords

compression test diverse structures energy absorption strain rate thin-wall tube 

Notes

Acknowledgments

One of the authors, Dipen Kumar Rajak, gratefully acknowledges the experimental support of LWMM group CSIR-AMPRI, Bhopal. The authors thank Director, CSIR-AMPRI Bhopal and Indian Institute of Technology (Indian School of Mines) Dhanbad for giving permission to publish this research work. The technical support of the CSIR-AMPRI Bhopal during the Ph.D. research program of Dipen Kumar Rajak is highly appreciated.

References

  1. 1.
    J.M. Holdridge, V.N. Shankar, and G.F. Ulfarsson, The Crash Severity Impacts of Fixed Roadside Objects, J. Safety Res., 2005, 36(2), p 139–147CrossRefGoogle Scholar
  2. 2.
    L. Guo and J. Yu, Dynamic Bending Response of Double Cylindrical Tubes Filled with Aluminum Foam, Int. J. Impact Eng, 2011, 238(2), p 85–94CrossRefGoogle Scholar
  3. 3.
    M.M. Abedi, A. Niknejad, G.H. Liaghat, and M.Z. Nejad, Theoretical and Experimental Study on Empty and Foam-Filled Columns with Square and Rectangular Cross Section Under Axial Compression, Int. J. Mech. Sci., 2012, 65(1), p 134–146CrossRefGoogle Scholar
  4. 4.
    A. Darvizeh, M. Darvizeh, R. Ansari, and A. Meshkinzar, Effect of Low Density, Low Strength Polyurethane Foam on The Energy Absorption Characteristics of Circumferentially Grooved Thick-Walled Circular Tubes, Thin Wall. Struct., 2013, 71, p 81–90CrossRefGoogle Scholar
  5. 5.
    A.G. Hanssen, M. Langseth, and O.S. Hopperstad, Optimum Design for Energy Absorption of Square Aluminium Columns with Aluminium Foam Filler, Int. J. Mech. Sci., 2001, 43(1), p 153–176CrossRefGoogle Scholar
  6. 6.
    M. Guden and H. Kavi, Quasi-Static Axial Compression Behaviour of Constraint Hexagonal and Square-Packed Empty and Aluminum Foam-Filled Aluminum Multi-Tubes, Thin Wall. Struct., 2006, 44(7), p 739–750CrossRefGoogle Scholar
  7. 7.
    A.G. Hanssen, M. Langseth, and O.S. Hopperstad, The Static and Dynamic Crushing of Circular Aluminium Extrusions with Aluminium Foam Filler, Int. J. Impact Eng, 2000, 24(5), p 475–507CrossRefGoogle Scholar
  8. 8.
    A.G. Hanssen, M. Langseth, and O.S. Hopperstad, Static and Dynamic Crushing of Square Aluminium Extrusions with Aluminium Foam Filler, Int. J. Impact Eng, 2000, 24(4), p 347–383CrossRefGoogle Scholar
  9. 9.
    J.M. Babbage and P.K. Mallick, Static Axial Crush Performance of Unfilled and Foam-Filled Aluminium–Composite Hybrid Tubes, Compos. Struct., 2005, 70(2), p 177–184CrossRefGoogle Scholar
  10. 10.
    S.R. Guillow, G. Lu, and R.H. Grzebieta, Quasi-Static Axial Compression of Thin-Walled Circular Aluminium Tubes, Int. J. Mech. Sci., 2001, 43, p 2103–2123CrossRefGoogle Scholar
  11. 11.
    T.Y. Reddy and R.J. Wall, Axial Compression of Foam-Filled Thin-Walled Circular Tubes, Int. J. Impact Eng, 1988, 7, p 151–166CrossRefGoogle Scholar
  12. 12.
    A.G. Mamalis, D.E. Manolakos, G.A. Demosthenous, and W. Johnson, Axial Plastic Collapse of Thin Bi-Material Tubes as Energy Dissipating Systems, Int. J. Impact Eng, 1991, 11, p 185–196CrossRefGoogle Scholar
  13. 13.
    D.K. Rajak, L.A. Kumaraswamidhas, and S. Das, Investigation, and Characterization of Aluminium Alloy Foams with TiH2 as Foaming Agent, Mater. Sci. Technol., 2016, 32(13), p 1338–1345CrossRefGoogle Scholar
  14. 14.
    L.A. Kumaraswamidhas, D.K. Rajak, and S. Das, An Investigation on the Axial Deformation Behaviour of Thin-Wall Unfilled and Filled the Tube with Aluminium Alloy (Al–Si7 Mg) Foam-Reinforced with SiC Particles, J. Mater. Eng. Perform., 2016, 25(8), p 3430–3438CrossRefGoogle Scholar
  15. 15.
    D.K. Rajak, L.A. Kumaraswamidhas, and S. Das, An Energy Absorption Behaviour of Foam Filled Structures, Proc. Mater. Sci., 2014, 5, p 164–172CrossRefGoogle Scholar
  16. 16.
    G.J. Davies and S. Zhen, Metallic Foams: Their Production, Properties and Applications, J. Mater. Sci., 1983, 18(7), p 1899–1911CrossRefGoogle Scholar
  17. 17.
    L.J. Gibson, Metal Matrix Composite, Handbook, 3rd edn. Kelly Anthony, Zweben Carl, 2000, p 821Google Scholar
  18. 18.
    J. Banhart, Manufacturing Routes for Metallic Foams, J. Metal., 2000, 12, p 22–27Google Scholar
  19. 19.
    V. Gergely and T.W. Clyne, Drainage in Standing Liquid Metal Foams: Modelling and Experimental Observations, Acta Mater., 2004, 52, p 3047–3058CrossRefGoogle Scholar
  20. 20.
    C. Korner and R.F. Singer, Processing of Metal Foams—Challenges and Opportunities, Adv. Eng. Mater., 2000, 2(4), p 159–165CrossRefGoogle Scholar
  21. 21.
    I. Duarte, J. Mascarenhas, A. Ferreira, and J. Banhart, The Evolution of Morphology and Kinetics During the Foaming Process of Aluminium, Key Eng. Mater., 2002, 2320–232, p 96–101CrossRefGoogle Scholar
  22. 22.
    A.E. Simone and L.J. Gibson, Aluminium Foams Produced by Liquid-State Processes, Acta Mater., 1998, 46(9), p 3109–3123CrossRefGoogle Scholar
  23. 23.
    Y. Miyoshi, M. Itoh, S. Akiyama, and A. Kitahara, ALPORAS Aluminium Foam: Production Process, Properties, and Applications, Adv. Eng. Mater., 2002, 2(4), p 179–183CrossRefGoogle Scholar
  24. 24.
    W. Deqing and S. Ziyuan, Effect of Ceramic Particles on Cell Size and a Wall Thickness of Aluminium Foam, Mater. Sci. Eng., 2003, 361, p 45–49CrossRefGoogle Scholar
  25. 25.
    B. Kritzt, U. Martin, U. Mosler, Handbook of Cellular Metals: Production, Processing, Application, 2002, p 130Google Scholar
  26. 26.
    O. Prakash, H. Sang, and J.D. Embury, Structure and Properties of the Al–SiC Foam, Mater. Sci. Eng., A, 1995, 199, p 195–203CrossRefGoogle Scholar
  27. 27.
    S.W. Ip, Y. Wang, and J.D. Toguri, Aluminium Foam Stabilization by Solid Particles, Can. Matall. Q., 1999, 38(1), p 81–92CrossRefGoogle Scholar
  28. 28.
    A. Haibel, A. Rack, and J. Banhart, Why are Metal Foams Stable, Appl. Phys. Lett., 2006, 89(15), p 154102CrossRefGoogle Scholar
  29. 29.
    D.K. Rajak, L.A. Kumaraswamidhas, S. Das, and S.S. Kumaran, Characterization and Analysis of Compression Load Behaviour of Aluminium Alloy Foam Under the Diverse Strain Rate, J. Alloys Compd., 2016, 656, p 218–225CrossRefGoogle Scholar
  30. 30.
    D.K. Rajak, L.A. Kumaraswamidhas, and S. Das, Energy Absorption Capacity of Empty and Foam Filled Mild Steel Tube Under Low Strain Rate at Room Temperature, Adv. Mater. Lett., 2015, 6(6), p 548–553CrossRefGoogle Scholar

Copyright information

© ASM International 2018

Authors and Affiliations

  • Dipen Kumar Rajak
    • 1
    • 4
  • L. A. Kumaraswamidhas
    • 1
    • 2
  • S. Das
    • 3
  1. 1.Department of Mining Machinery EngineeringIndian Institute of Technology (ISM)DhanbadIndia
  2. 2.Advanced Research LabIndian Institute of Technology (ISM)DhanbadIndia
  3. 3.CSIR-Advanced Materials and Processes Research InstituteBhopalIndia
  4. 4.Department of Mechanical EngineeringSandip Institute of Technology and Research CentreNashikIndia

Personalised recommendations