Abstract
The basicity of mold flux has been recognized to have a significant influence on the mold flux crystallization in continuous casting, which would in turn affect the heat-transfer rate between the solidified shell and mold. The research regarding the mold flux crystallization as well as its effect on the heat transfer has been conducted intensively. However, few studies have been developed to specify the effect of basicity introduced mold flux crystallization on the radiative heat transfer and interfacial thermal resistance in continuous casting. By using an infrared radiation emitter, a radiative heat flux was applied to a copper mold covered with a solid mold flux disk to simulate the heat-transfer phenomena in continuous casting. The crystallization behaviors of mold fluxes with different basicities and their impact on the radiative heat transfer were investigated dynamically. The interfacial thermal resistance between the solid mold flux and copper mold was also studied in this article. The results suggested that the basicity tends to enhance the mold flux crystallization, leading to the reduction of radiative heat-transfer rate and enlargement of interfacial thermal resistance.
Similar content being viewed by others
References
K.C. Mills, A.B. Fox, Z. Li, and R.P. Thackray: Ironmaking Steelmaking, 2005, vol. 32, no. 1, pp. 26–34.
Y. Meng and B.G. Thomas: ISIJ Int., 2006, vol. 46, no. 5, pp. 660–69.
W. Wang and A.W. Cramb: ISIJ Int., 2005, vol. 45, no. 12, pp. 1864–70.
J.F. Holzhauser, K.H. Spitzer, and K. Schwerdtfeger: Steel Res., 1999, vol. 70, no. 7, pp. 252–58.
J.F. Holzhauser, K.H. Spitzer, and K. Schwerdtfeger: Steel Res., 1999, vol. 70, no. 10, pp. 430–36.
W. Wang, L.J. Zhou, and K.Z. Gu: Met. Mater. Int., 2010, vol. 16, no. 6, pp. 913–20.
J.W. Cho, T. Emi, H. Shibata, and M. Suzuki: ISIJ Int., 1998, vol. 38, no. 3, pp. 268–75.
K.C. Mills and A.B. Fox: ISIJ Int., 2003, vol. 43, no. 10, pp. 1479–86.
M. Hanao and M. Kawanoto: ISIJ Int., 2008, vol. 48, no. 2, pp. 180–85.
H. Matsuda, K. Saruhashi, J. Abu, H. Takada, H. Yasunaka, and S. Koyama: CAMP-ISIJ, 1992, vol. 5, no. 1, pp. 207–13.
Y. Meng and B.G. Thomas: Metall. Mater. Trans. B, 2003, vol. 34B, pp. 707–13.
J. Sengupta, H. Shin, B.G. Thomas, and S.-H. Kim: Acta Mater., 2006, vol. 54, no. 6, pp. 1165–73.
A.Yamauchi, K. Sorimachi, T. Sakuraya, and T. Fujii: ISIJ Int., 1993, vol. 33, no. 1, pp. 140–47.
M. Susa, A. Kushimoto, H. Toyota, M. Hayashi, R. Endo, and Y. Kobayashi: ISIJ Int., 2009, vol. 49, no. 11, pp. 1722–29.
K. Watanade, M. Suzuki, K. Murakami, H. Kondo, A. Miyamoto, and T. Shiomi: Tetsu-to-Hagané, 1997, vol. 83, no. 2, pp. 115–20.
K. Tsutsumi, T. Nagasaka, and M. Hino: ISIJ Int., 1999, vol. 39, no. 11, pp. 1150–59.
H. Mizuno, H. Esaka, K. Shinozuka, and M. Tamura: ISIJ Int., 2008, vol. 48, no. 3, pp. 277–85.
M. Hanao, M. Kawanoto, M. Hara, T. Murakami, H. Kikuchi, and K. Hanazaki: Tetsu-to-Hagané, 2002, vol. 88, no. 1, pp. 23–28.
H. Nakada, M. Suza, Y. Seko, M. Hayashi, and K. Nagata: ISIJ Int., 2008, vol. 48, no. 4, pp. 446–53.
J.W. Cho, H. Shibata, T. Emi, and M. Suzuki: ISIJ Int., 1998, vol. 38, no. 5, pp. 440–46.
B.G. Thomas, B. Ho, and G. Li: Alex Mclean Symposium Proc., Iron and Steel Society, Warrendale, PA, 1988, pp. 177–93.
Z. Li, R. Thackray, and K.C. Mills: VII Int. Conf. on Molten Slags, Fluxes and Slats, The South African Institute of Mining and Metallurgy, Johannesburg, South Africa, 2004, pp. 813–20.
M. Persson, M. Gornerup, and S. Seetharaman: ISIJ Int., 2007, vol. 47, no. 10, pp. 1533–40.
K.C. Mills: ISIJ Int., 1993, vol. 33, no. 1, pp. 148–55.
K. Prapakorn: Ph.D. Thesis, Carnegie Mellon University, Pittsburgh, PA, 2003.
W. Wang: Ph.D. Thesis, Carnegie Mellon University, Pittsburgh, PA, 2007, pp. 107–20.
L. Zhou, W. Wang, F. Ma, J. Li, J. Wei, H. Matsuura, and F. Tsukihashi: Metall. Mater. Trans. B, 2011, DOI: 10.1007/s11663-011-9591-5, in press.
M. Hayashi, T. Watanabe, H. Nakada, and K. Nagata: ISIJ Int., 2006, vol. 46, no. 12, pp. 1805–09.
T. Watanabe, H. Hashimoto, M. Hayashi, and K. Nagata: ISIJ Int., 2008, vol. 48, no. 7, pp. 925–33.
W. Wang, K. Gu, L. Zhou, F. Ma, I. Sohn, D.J. Min, H. Matsuura, and F. Tsukihashiet: ISIJ Inter., 2011, vol. 51, no. 11, pp. 1838–45.
S. Ozawa, M. Susa, T. Goto, R. Endo, and K.C. Mills: ISIJ Int., 2006, vol. 46, no. 3, pp. 413–19.
Y. Shiraishi: Handbook of Physico-Chemical Properties at High Temperature, ISIJ International, Tokyo, Japan, 1988, ch. 10.
W. Wang and A.W. Cramb: AIST Trans., 2008, vol. 5, pp. 155–60.
K. Tsutumi, T. Nagasaka, and M. Hino: ISIJ Int., 1999, vol. 39, no. 11, pp. 1150–59.
J.W. Cho, T. Emi, H. Shibata, and M. Suzuki: ISIJ Int., 1998, vol. 38, no. 8, pp. 834–42.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted October 25, 2011.
Rights and permissions
About this article
Cite this article
Gu, K., Wang, W., Zhou, L. et al. The Effect of Basicity on the Radiative Heat Transfer and Interfacial Thermal Resistance in Continuous Casting. Metall Mater Trans B 43, 937–945 (2012). https://doi.org/10.1007/s11663-012-9644-4
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11663-012-9644-4