Abstract
For MBF-51 filler, the brazed joint consists of interfacial grain boundary borides, coarse Nb6Ni16Si7, and Ni/Cr-rich matrix. In contrast, the VZ-2106 brazed joint is composed of interfacial Nb6Ni16Si7 precipitates as well as grain boundary borides, coarse Nb6Ni16Si7, and Ni/Cr/Fe-rich matrix. The maximum tensile strength of 443 MPa is obtained from the MBF-51 brazed specimen. The tensile strengths of VZ-2106 brazed joints are approximately 300 MPa. Both amorphous filler foils demonstrate potential in brazing IN-625 substrate.
Similar content being viewed by others
References
J.R. Davis: ASM Handbook, Vol. 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International, Materials Park, OH, 1990, pp. 428–45.
W.F. Smith: Structure and Properties of Engineering Alloys, McGraw-Hill Inc., New York, NY, 1993, pp. 494–98.
D. L. Olson: ASM Handbook, Vol. 6: Welding Brazing and Soldering, ASM International, Materials Park, OH, 1990, pp. 911–29.
M. Schwartz: Brazing: For the Engineering Technologist, ASM International, Materials Park, OH, 1995, pp. 141–45.
G. Humpston and D.M. Jacobson: Principles of Soldering and Brazing, ASM International, Materials Park, OH, 1993, pp. 47–50.
C.L. Ou, D.W. Liaw, Y.C. Du and R.K. Shiue: J. Mater. Sci., 2006, vol. 41, pp. 6353–61.
R. K. Shiue, S.K. Wu, and C.M. Hung: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1765–73.
A. Rabinkin, E. Wenski, and A. Ribaudo: Weld. J., 1988, vol. 67, no. 2, pp. 66s–75s.
A. Rabinkin and S. Pounds: Weld. J., 1988, vol. 67, no. 5, pp. 33–45.
A. Rabinkin: Weld. J., 1988, vol. 67, no. 10, pp. 29–30.
A. Rabinkin: Sci. Tech. Weld. J., 2004, vol. 9, no. 3, pp. 181–99.
W.D. Zhuang and T.W. Eagar: Weld. J., 1997, vol. 76 (12), pp. 526s–31s.
E.A. Leone, A. Rabinkin, and B. Sarna: J. Adv. Mater., vol. 38 (2), pp. 28–39.
P. Villars, A. Prince, and H. Okamoto: Handbook of Ternary Alloy Phase Diagrams, ASM International, Materials Park, OH, 1995.
The authors gratefully acknowledge the financial support of this research by National Science Council, Republic of China under NSC Grant 99-2221-E-002-120-MY3.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted November 9, 2011.
Rights and permissions
About this article
Cite this article
Chen, WS., Shiue, RK. Brazing Inconel 625 Using Two Ni/(Fe)-Based Amorphous Filler Foils. Metall Mater Trans A 43, 2177–2182 (2012). https://doi.org/10.1007/s11661-012-1174-9
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-012-1174-9