Skip to main content
SpringerLink
Log in

An Investigation on Microstructure and Mechanical Properties of Nd:YAG Laser Beam Weld of Copper Beryllium Alloy

  • Published:
Metallurgical and Materials Transactions A Aims and scope Submit manuscript

Abstract

Nd:YAG pulsed laser beam welding is conducted on UNS-C17200 copper beryllium sheet. Welding is carried out in the as-annealed and as-aged conditions to investigate the effects of preweld condition on weld microstructure and mechanical properties. Two different heat treatments including direct age treating and solution annealing + subsequent age treating are considered after welding. The mechanical and microstructural characteristics of weld metal regions (WMs) and heat-affected zones (HAZ) of four different samples are considered using tensile tests, hardness measurements, optical microscopy, electron microscopy, and X-ray diffraction (XRD). Results indicate that the microstructural and mechanical properties of the HAZ without postweld treatment are adversely affected by grain boundary liquation observed if welding is carried out in the as-aged condition. Tensile strength and hardness of the WM are improved after a postweld artificial age treatment at 315 °C for 3 hours. However, hardness of the WM is lower than that of the base metal (BM) and HAZ, because the precipitation mechanism in the fusion zone is not as effective as that is in the HAZ and BM. The CuBe secondary phase precipitates during solidification. The precipitates/matrix interface is incoherent, which does not significantly raise the hardness of the weld metal. Incoherent interdendritic precipitates are dissolved in the weld structure after postweld solution annealing. Having performed postweld solution treatment and aging, full strength and hardness throughout the copper beryllium material were observed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11

Similar content being viewed by others

References

  1. J.C. Harkness and A. Guha: Metallography and Microstructures, vol. 9, ASM Handbook, ASM INTERNATIONAL, Metals Park, OH, 2004, pp. 752–61.

  2. R.J. Rioja and D.E. Laughlin: Metall. Mater. Trans. A, 1984, vol. 15A, pp. 939–41.

    ADS  Google Scholar 

  3. W.C. Crone: J. Cryst. Growth, 1999, vol. 218, pp. 381–89.

    Article  ADS  Google Scholar 

  4. H. Era and K. Kishitake: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 2765–71.

    Article  ADS  CAS  Google Scholar 

  5. R. Monzen, C. Watanabe, and D. Mino: Acta Mater., 2004, vol. 53 (4), pp. 1153–61.

    Google Scholar 

  6. S. Zalkind and D. Moreno: J. Mater. Sci. Lett., 1999, vol. 18, pp. 849–52.

    Article  CAS  Google Scholar 

  7. Alloys Phase Diagrams, vol. 3, ASM Handbook, ASM INTERNATIONAL, Metals Park, OH, 2004.

  8. S. Kou: Welding Metallurgy, Wiley, New York, NY, 2003, p. 155.

    Google Scholar 

  9. Z. Zhao, C. Wang, and N. Li: Appl. Surf. Sci., 2006, vol. 252 (11), pp. 4257–63.

    Article  ADS  CAS  Google Scholar 

  10. G.G. Roy, J.W. Elmer, and T. DebRoy: J. Appl. Phys., 2001, vol. 100, pp. 805–903.

    Google Scholar 

  11. B. Chalmers: Principles of Solidification, Wiley, New York, NY, 1964, p. 117.

    Google Scholar 

  12. O. A. Ojo and N.L. Richards: Scripta Mater., 2004, vol. 54, pp. 641–46.

    Google Scholar 

  13. C.M. Cheng and C.P. Chou: Mater. Sci. Technol., 2006, vol. 22, pp. 685–90.

    CAS  Google Scholar 

  14. Y. Rosenthal: J. Mater. Sci., 1992, vol. 27 (8), pp. 2193–98.

    Article  ADS  CAS  Google Scholar 

Download references

Acknowledgment

The authors express their gratitude to the School of Metallurgy and Materials Engineering, University of Tehran, for providing SEM and XRD equipments.

Author information

Authors and Affiliations

  1. School of Metallurgy and Materials Engineering, University College of Engineering, University of Tehran, Tehran, 14395-515, Iran

    S.A.A. Akbari Mousavi (Associate Professor) & S.T. Niknejad (Research Assistant)

Authors
  1. S.A.A. Akbari Mousavi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S.T. Niknejad
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S.A.A. Akbari Mousavi.

Additional information

Manuscript submitted October 18, 2008.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Akbari Mousavi, S., Niknejad, S. An Investigation on Microstructure and Mechanical Properties of Nd:YAG Laser Beam Weld of Copper Beryllium Alloy. Metall Mater Trans A 40, 1469–1478 (2009). https://doi.org/10.1007/s11661-009-9822-4

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11661-009-9822-4

Keywords

Search

Navigation